Move the ngene/ddbridge firmware into their drivers.
There are two reasons for that:
1) The firmware used there didn't work for a few devices
I tested here (Terratec H5, H6 and H7);
2) At least Terratec H7 doesn't seem to require a firmware
for it to work.
After this change, if firmware is not specified, the driver will
use a rom-based firmware (this seems to be the case for Terratec
H7, although I need to better check the USB dumps to be sure about
that).
In any case, the firmware seems to be optional, as the DRX-K driver
don't return the firmware load error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mutex is there to protect the I2C gate. However, for some reason,
it is being called twice:
[ 2103.542796] usbcore: registered new interface driver dvb_usb_az6007
[ 2103.772392] az6007: drxk_gate_ctrl: enable
[ 2103.793900] az6007: drxk_gate_ctrl: enable
For now, let's just comment, to allow the driver to run.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mt2063 uses a one-byte transfer. This requires a special handling
inside the i2c code. Fix it to properly accept i2c reads. This
is needed to make the mt2063 to be detected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add some fixes to allow frontend attachment. The patch is not
complete yet, as just the frontend 0 is initialized. So, more
changes will be needed, including some changes at dvb-usb core.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some changes are needed, in order to make az6007 compile with the
upstream tree. Most of the changes are due to the upstream drxk
module.
Even allowing its compilation, the driver is not working yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Import the az6007 driver from Terratec H7 source, as-is.
It won't compile or run, so latter patches are needed in order
to fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable and disable the clocks to the SPI controller using runtime PM. This
serves the dual purpose of reducing power consumption a little and letting
the core know when the device is idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Although the hardware supports interrupts we're not currently using them
at all since for small transfers the overhead is greater than that for
busy waiting and for large transfers we have interrupts from the DMA.
This means that if the hardware reports an error (especially one which
might not stall transfer) we might miss it.
Take a first pass at dealing with such errors by enabling the interrupt
if we can and logging the errors if they happen. Ideally we'd report the
error via the affected transfer but since we're in master mode it's very
difficult to trigger errors at present and this code is much simpler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
With the conversion of atomicio's routines in place (see commits
6f68c91c55 and 700130b41f), atomicio.[ch] can be removed, replacing
the APEI specific pre-mapping capabilities with the more generalized
versions that drivers/acpi/osl.c provides.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds support for RAM to ACPI's mapping capabilities in order
to support APEI error injection (EINJ) actions.
This patch re-factors similar functionality introduced in commit
76da3fb357, bringing it into osl.c in preparation for removing
./drivers/acpi/atomicio.[ch].
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Base ACPI (CA) currently does not support atomic 64-bit reads and writes
(acpi_read() and acpi_write() split 64-bit loads/stores into two
32-bit transfers) yet APEI expects 64-bit transfer capability, even
when running on 32-bit systems.
This patch implements 64-bit read and write routines for APEI usage.
This patch re-factors similar functionality introduced in commit
04c25997c9, bringing it into the ACPI subsystem in preparation for
removing ./drivers/acpi/atomicio.[ch]. In the implementation I have
replicated acpi_os_read_memory() and acpi_os_write_memory(), creating
64-bit versions for APEI to utilize, as opposed to something more
elegant. My thinking is that we should attempt to see if we can get
ACPI's CA/OSL changed so that the existing acpi_read() and acpi_write()
interfaces are natively 64-bit capable and then subsequently remove the
replication.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In the "xchg" implementation, %ebx and %ecx don't need to be copied
into %eax and %edx respectively (this is only necessary when desiring
to only read the stored value).
In the "add_unless" implementation, swapping the use of %ecx and %esi
for passing arguments allows %esi to become an input only (i.e.
permitting the register to be re-used to address the same object
without reload).
In "{add,sub}_return", doing the initial read64 through the passed in
%ecx decreases a register dependency.
In "inc_not_zero", a branch can be eliminated by or-ing together the
two halves of the current (64-bit) value, and code size can be further
reduced by adjusting the arithmetic slightly.
v2: Undo the folding of "xchg" and "set".
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/4F19A2BC020000780006E0DC@nat28.tlf.novell.com
Cc: Luca Barbieri <luca@luca-barbieri.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Eric pointed out overly restrictive constraints in atomic64_set(), but
there are issues throughout the file. In the cited case, %ebx and %ecx
are inputs only (don't get changed by either of the two low level
implementations). This was also the case elsewhere.
Further in many cases early-clobber indicators were missing.
Finally, the previous implementation rolled a custom alternative
instruction macro from scratch, rather than using alternative_call()
(which was introduced with the commit that the description of the
change in question actually refers to). Adjusting has the benefit of
not hiding referenced symbols from the compiler, which however requires
them to be declared not just in the exporting source file (which, as a
desirable side effect, in turn allows that exporting file to become a
real 5-line stub).
This patch does not eliminate the overly restrictive memory clobbers,
however: Doing so would occasionally make the compiler set up a second
register for accessing the memory object (to satisfy the added "m"
constraint), and it's not clear which of the two non-optimal
alternatives is better.
v2: Re-do the declaration and exporting of the internal symbols.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/4F19A2A5020000780006E0D9@nat28.tlf.novell.com
Cc: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Mauro Carvalho Chehab