This is required to split SoC bus init into two phases. The later one
(which includes scanning) should be called when kalloc is available.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change is important for SoC host. In future we will want to know
chip ID (needed for early MIPS boot) before doing cores scanning.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As checkpatch suggests:
WARNING: Possible unnecessary 'out of memory' message,
remove an error message after failing kmalloc() from the PLL driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It removes the owner field updation of driver structure.
It will be automatically updated by module_platform_driver()
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the date type of error status from u64 to atomic_long_t, and use atomic
operation, then remove the lock which is used to protect the error status.
The operation of atomic maybe faster than spin lock.
Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes an unncessary check in the br_afspec() method of
br_netlink.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
bridge: implement rtnl_link options for getting and setting bridge options
So far, only sysfs is complete interface for getting and setting bridge
options. This patchset follows-up on the similar bonding code and
allows userspace to get/set bridge master/port options using Netlink
IFLA_INFO_DATA/IFLA_INFO_SLAVE_DATA attr.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow rtnetlink users to set bridge master info via IFLA_INFO_DATA attr
This initial part implements forward_delay, hello_time, max_age options.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow rtnetlink users to get bridge master info in IFLA_INFO_DATA attr
This initial part implements forward_delay, hello_time, max_age options.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow rtnetlink users to set port info via IFLA_INFO_SLAVE_DATA attr
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow rtnetlink users to get port info in IFLA_INFO_SLAVE_DATA attr
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The thing is that netdev_master_upper_dev_link calls
call_netdevice_notifiers(NETDEV_CHANGEUPPER, dev). That generates rtnl
link message and during that, rtnl_link_ops->fill_slave_info is called.
But with current ordering, rx_handler and IFF_BRIDGE_PORT are not set
yet so there would have to be check for that in fill_slave_info callback.
Resolve this by reordering to similar what bonding and team does to
avoid the check.
Also add removal of IFF_BRIDGE_PORT flag into error path.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg <johannes@sipsolutions.net> says:
"Two more fixes for mac80211 - one of them addresses a long-standing
issue that we only found when using vendor events more frequently;
the other addresses some bad information being reported in userspace
that people were starting to actually look at."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net.ipv4.ip_nonlocal_bind sysctl was global to all network
namespaces. This patch allows to set a different value for each
network namespace.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull arch/microblaze fixes from Michal Simek:
- Kconfig menu structure fix
- fix number of syscalls
- fix compilation warnings from allmodconfig
* tag 'microblaze-3.17-rc5' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix number of syscalls
microblaze: Rename Advance setup to Kernel features
microblaze: Add mm/Kconfig to advance menu
arch/microblaze/include/asm/uaccess.h: Use pr_devel() instead of pr_debug()
arch/microblaze/include/asm/entry.h: Include "linux/linkage.h" to avoid compiling issue
Alexei Starovoitov says:
====================
load imm64 insn and uapi/linux/bpf.h
V9->V10
- no changes, added Daniel's ack
Note they're on top of Hannes's patch in the same area [1]
V8 thread with 'why' reasoning and end goal [2]
Original set [3] of ~28 patches I'm planning to present in 4 stages:
I. this 2 patches to fork off llvm upstreaming
II. bpf syscall with manpage and map implementation
III. bpf program load/unload with verifier testsuite (1st user of
instruction macros from bpf.h and 1st user of load imm64 insn)
IV. tracing, etc
[1] http://patchwork.ozlabs.org/patch/385266/
[2] https://lkml.org/lkml/2014/8/27/628
[3] https://lkml.org/lkml/2014/8/26/859
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
allow user space to generate eBPF programs
uapi/linux/bpf.h: eBPF instruction set definition
linux/filter.h: the rest
This patch only moves macro definitions, but practically it freezes existing
eBPF instruction set, though new instructions can still be added in the future.
These eBPF definitions cannot go into uapi/linux/filter.h, since the names
may conflict with existing applications.
Full eBPF ISA description is in Documentation/networking/filter.txt
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add BPF_LD_IMM64 instruction to load 64-bit immediate value into a register.
All previous instructions were 8-byte. This is first 16-byte instruction.
Two consecutive 'struct bpf_insn' blocks are interpreted as single instruction:
insn[0].code = BPF_LD | BPF_DW | BPF_IMM
insn[0].dst_reg = destination register
insn[0].imm = lower 32-bit
insn[1].code = 0
insn[1].imm = upper 32-bit
All unused fields must be zero.
Classic BPF has similar instruction: BPF_LD | BPF_W | BPF_IMM
which loads 32-bit immediate value into a register.
x64 JITs it as single 'movabsq %rax, imm64'
arm64 may JIT as sequence of four 'movk x0, #imm16, lsl #shift' insn
Note that old eBPF programs are binary compatible with new interpreter.
It helps eBPF programs load 64-bit constant into a register with one
instruction instead of using two registers and 4 instructions:
BPF_MOV32_IMM(R1, imm32)
BPF_ALU64_IMM(BPF_LSH, R1, 32)
BPF_MOV32_IMM(R2, imm32)
BPF_ALU64_REG(BPF_OR, R1, R2)
User space generated programs will use this instruction to load constants only.
To tell kernel that user space needs a pointer the _pseudo_ variant of
this instruction may be added later, which will use extra bits of encoding
to indicate what type of pointer user space is asking kernel to provide.
For example 'off' or 'src_reg' fields can be used for such purpose.
src_reg = 1 could mean that user space is asking kernel to validate and
load in-kernel map pointer.
src_reg = 2 could mean that user space needs readonly data section pointer
src_reg = 3 could mean that user space needs a pointer to per-cpu local data
All such future pseudo instructions will not be carrying the actual pointer
as part of the instruction, but rather will be treated as a request to kernel
to provide one. The kernel will verify the request_for_a_pointer, then
will drop _pseudo_ marking and will store actual internal pointer inside
the instruction, so the end result is the interpreter and JITs never
see pseudo BPF_LD_IMM64 insns and only operate on generic BPF_LD_IMM64 that
loads 64-bit immediate into a register. User space never operates on direct
pointers and verifier can easily recognize request_for_pointer vs other
instructions.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes kernel panic/interrupt storm/etc issues if bootloader
left s3c-hsotg module in enabled state. Now interrupt handler is enabled
only after proper configuration of hardware registers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Generic PHY Framework a NULL phy is considered to be a valid phy
thus the "if (hsotg->phy)" check does not give us the information whether
the Generic PHY Framework is used.
In addition to the above this patch also removes phy_init from probe and
phy_exit from remove. This is not necessary when init/exit is done in the
s3c_hsotg_phy_enable/disable functions.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver is removed s3c_hsotg_phy_disable is called three times
instead of once. This results in decreasing of the phy reference counter
below zero and thus consecutive inserts of the module fails.
This patch removes calls to s3c_hsotg_phy_disable from s3c_hsotg_remove
and s3c_hsotg_udc_stop.
s3c_hsotg_udc_stop is called from udc-core.c only after
usb_gadget_disconnect, which in turn calls s3c_hsotg_pullup, which
already calls s3c_hsotg_phy_disable.
s3c_hsotg_remove must be called only after udc_stop, so there is no
point in disabling phy once again there.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a queue is registered, the block layer turns off the bypass
setting (because bypass is enabled when the queue is created). This
doesn't work well for queues that are unregistered and then registered
again; we get a WARNING because of the unbalanced calls to
blk_queue_bypass_end().
This patch fixes the problem by making blk_register_queue() call
blk_queue_bypass_end() only the first time the queue is registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tejun Heo <tj@kernel.org>
CC: James Bottomley <James.Bottomley@HansenPartnership.com>
CC: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
On systems with special thermal configurations make sure we make
note of the thermal setup. This is required for proper firmware
configuration on these systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Pull "SOCFPGA driver update for v3.18" from Dinh Nguyen:
This is the EDAC driver for EDAC. Boris had given me permission to
take this patch together with it's DTS component. The DTS portion was in the
previous pull request.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'socfpga_driver_for_v3.18' of git://git.rocketboards.org/linux-socfpga-next:
edac: altera: Add Altera SDRAM EDAC support
The bootloader on the Netgear ReadyNAS RN2120 uses Hardware BCH
ECC (strength = 4), while the pxa3xx NAND driver by default uses
Hamming ECC (strength = 1).
This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.
The issue was initially reported and fixed by Ben Pedell for
RN102. The RN2120 shares the same Hynix H27U1G8F2BTR NAND
flash and setup. This patch is based on Ben's fix for RN102.
Fixes: ad51eddd95 ("ARM: mvebu: Enable NAND controller in ReadyNAS 2120 .dts file")
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/61f6a1b7ad0adc57a0e201b9680bc2e5f214a317.1410035142.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The bootloader on the Netgear ReadyNAS RN104 uses Hardware BCH
ECC (strength = 4), while the pxa3xx NAND driver by default uses
Hamming ECC (strength = 1).
This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.
The issue was initially reported and fixed by Ben Pedell for
RN102. The RN104 shares the same Hynix H27U1G8F2BTR NAND
flash and setup. This patch is based on Ben's fix for RN102.
Fixes: 0373a558bd ("ARM: mvebu: Enable NAND controller in ReadyNAS 104 .dts file")
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/920c7e7169dc6aaaa3eb4bced2336d38e77b8864.1410035142.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the SSCG (Spread Spectrum Clock Generator) is enabled, it shifts
the frequency of the clock. The percentage is no more than 1% but when
the clock is used for a timer it leads to a clock drift.
This patch allows to correct the affected clock when the SSCG is
enabled. The check is done in an new optional function related to each
SoC: is_sscg_enabled(). The fix is done with the other new optional
function related to each SoC: fix_sscg_deviation. If one these
functions are not present then no correction is done on the clock
frequency.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Link: https://lkml.kernel.org/r/1409645719-20003-2-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull "Third Round of Renesas ARM Based SoC Soc Updates for v3.18" from Simon Horman:
* Initial r8a7794 SoC support
* Support Cortex-A7 in shmobile_init_delay()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'renesas-soc3-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Initial r8a7794 SoC support
ARM: shmobile: support Cortex-A7 in shmobile_init_delay()
Pull "Renesas ARM Based SoC r8a7740 Multiplatform Updates for v3.18" from Simon Horman:
* Enable multiplatform support for r8a7740 SoC and remove
its DT-reference C board DTS files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'renesas-r8a7740-multiplatform-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: armadillo800eva reference: Remove DTS
ARM: shmobile: armadillo800eva reference: Remove C board code
ARM: shmobile: r8a7740: Add restart callback
ARM: shmobile: armadillo800eva: Build DTS for multiplatform
ARM: shmobile: armadillo800eva: Sync DTS
ARM: shmobile: r8a7740: Multiplatform support
This patch introduces ioctl named FUNCTIONFS_ENDPOINT_DESC, which
returns endpoint descriptor to userspace. It works only if function
is active.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull "Second batch of AT91 cleanup for 3.18" from Nicolas Ferre:
- Timer Counter (TC) fixup and cleanup:
- fix segmentation fault when kexec-ing a kernel by masking
TC interrupts at shutdown and probe time
- use modern driver model: devm_*, probe function, sanitize IRQ request
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'at91-cleanup2' of git://github.com/at91linux/linux-at91:
clocksource: tcb_clksrc: sanitize IRQ request
ARM: at91/tclib: mask interruptions at shutdown and probe
ARM: at91/tclib: move initialization from alloc to probe
ARM: at91/tclib: prefer using of devm_* functions
Add reset API at usb_gadget_driver, it calls disconnect handler currently,
but may do different things in future.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add reset API at usb_gadget_driver, it calls disconnect handler currently,
but may do different things in future.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Larry Finger