This patch adds support for the CycloneV and ArriaV SDRAM controllers.
Correction and reporting of SBEs, Panic on DBEs.
There was a discussion thread on whether this driver should be an mfd driver
or just make use of syscon, which is already a mfd. Ultimately, the
decision to use a simple syscon interface was reached.[1]
[1] https://lkml.org/lkml/2014/7/30/514
[dinguyen] Fixed Kconfig to have EDAC_ALTERA_MC as a tristate to prevent a
build failure for allmodconfig.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Acked-by: Borislav Petkov <bp@suse.de>
[dinguyen] cleaned up commit message
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
There is an ongoing work on cleaning MIPS's nvram support so it could be
re-used on other platforms (bcm53xx to say precisely).
This will require a bit of extra logic in bcma this patch implements.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg <johannes@sipsolutions.net> says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/wil6210/wmi.c
Johannes Berg <johannes@sipsolutions.net> says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
Signed-off-by: John W. Linville <linville@redhat.com>
Device tree is not enabled in some architecture where gpio
driver mcp23s08 is still required.
v2-changes:
- Parse device tree properties into platform data other than
individual variables.
v3-changes:
- Use of_node in gpio_chip device structure, because the
struct device * always has an of_node which is NULL when
OF is not used.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This test currently fails on 32-bit systems since we use u64 type to pass the
flags to fcntl.
This commit changes this to use 'unsigned int' type for flags to fcntl making it
work on 32-bit systems.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Pull hwmon bugfix from Guenter Roeck:
"Fix a bug in the ds1621 driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ds1621) Update zbits after conversion rate change
Pull x86 platform drivers fixes from Darren Hart:
"This is my first pull request since taking on maintenance for the
platform-drivers-x86 tree from Matthew Garrett. These have passed my
build testing and been run through Fengguang's LKP tests. Due to
timing this round, these have not spent any time in linux-next. I
have asked Stephen to include my for-next branch in linux-next going
forward, once he's back from vacation.
Details from tag:
- toshiba_acpi: re-enable hotkeys and cleanups
- ideapad-laptop: revert touchpad disable, and cleanup static/const
usage
- MAINTAINERS: update platform-drivers-x86 maintainer and tree"
* tag 'platform-drivers-x86-v3.17-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
toshiba_acpi: fix and cleanup toshiba_kbd_bl_mode_store()
platform/x86: toshiba: re-enable acpi hotkeys after suspend to disk
ideapad-laptop: Constify DMI table for real!
Revert "ideapad-laptop: Disable touchpad interface on Yoga models"
MAINTAINERS: Update platform-drivers-x86 maintainer and tree
Run these two scripts concurrently:
for ((; ;))
{
mkdir /cgroup/sub
rmdir /cgroup/sub
}
for ((; ;))
{
echo $$ > /cgroup/sub/cgroup.procs
echo $$ > /cgroup/cgroup.procs
}
A kernel bug will be triggered:
BUG: unable to handle kernel NULL pointer dereference at 00000038
IP: [<c10bbd69>] cgroup_put+0x9/0x80
...
Call Trace:
[<c10bbe19>] cgroup_kn_unlock+0x39/0x50
[<c10bbe91>] cgroup_kn_lock_live+0x61/0x70
[<c10be3c1>] __cgroup_procs_write.isra.26+0x51/0x230
[<c10be5b2>] cgroup_tasks_write+0x12/0x20
[<c10bb7b0>] cgroup_file_write+0x40/0x130
[<c11aee71>] kernfs_fop_write+0xd1/0x160
[<c1148e58>] vfs_write+0x98/0x1e0
[<c114934d>] SyS_write+0x4d/0xa0
[<c16f656b>] sysenter_do_call+0x12/0x12
We clear cgrp->kn->priv in the end of cgroup_rmdir(), but another
concurrent thread can access kn->priv after the clearing.
We should move the clearing to css_release_work_fn(). At that time
no one is holding reference to the cgroup and no one can gain a new
reference to access it.
v2:
- move RCU_INIT_POINTER() into the else block. (Tejun)
- remove the cgroup_parent() check. (Tejun)
- update the comment in css_tryget_online_from_dir().
Cc: <stable@vger.kernel.org> # 3.15+
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use of unmask/mask in set_wake was an incorrect implementation. The new
implementation correctly sets wakeup for the gpio chip's IRQ so the gpio chip
will not sleep while wakeup-enabled gpio are in use.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the value used to specify that interrupts from the gpio should
be routed to the application processor is hardcoded for all Qualcomm SoCs.
But the new APQ8084 SoC uses a different value. To resolve this, we make
this value configurable for each SoC. For all existing SoCs we continue
to use the current value, and only for APQ8084 we use the new value.
Suggested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patchset adds pinctrl support for the Qualcomm APQ8084 platform.
This set of patches adds pinctrl support for the Qualcomm APQ8084 platform.
The first patch adds the pin definitions. The second patch contains the
devicetree binding documentation. The third patch adds the DT node.
The last patch makes the INTR_TARGET_PROC_APPS value configurable and
defines it for each existing SoC.
Tested on IFC6540 board.
Changes since v3:
- Fixed the sdc valid pin values in the binding documentation - sdc2
instead of sdc3. (suggested by Bjorn Andersson)
Changes since v2:
- Fixed some incorrect bits and offsets. (suggested by Bjorn Andersson)
- Updated binding documentation to follow the format of msm8960.
(suggested by Bjorn Andersson)
- Added fourth patch, which removes the hardcoded INTR_TARGET_PROC_APPS
value and makes it configurable. Also we keep the current value for
existing SoCs. (suggested by Bjorn Andersson)
Changes since v1:
- Updated the total number of pins (suggested by Bjorn Andersson)
- Added the missing pin info (provided by Andy Gross)
- Updated groups and functions to be consistent with other pinctrls.
(suggested by Andy Gross)
- Removed unused functions, qdss and test pins. (suggested by Andy Gross)
- Updated the documentation with the possible functions.
Reviewed-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull sound fixes from Takashi Iwai:
"This time it contains a bunch of small ASoC fixes that slipped from in
previous updates, in addition to the usual HD-audio fixes and the
regression fixes for FireWire updates in 3.17.
All commits are reasonably small fixes"
* tag 'sound-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix COEF setups for ALC1150 codec
ASoC: simple-card: Fix bug of wrong decrement DT node's refcount
ALSA: hda - Fix digital mic on Acer Aspire 3830TG
ASoC: omap-twl4030: Fix typo in 2nd dai link's platform_name
ALSA: firewire-lib/dice: add arrangements of PCM pointer and interrupts for Dice quirk
ALSA: dice: fix wrong channel mappping at higher sampling rate
ASoC: cs4265: Fix setting of functional mode and clock divider
ASoC: cs4265: Fix clock rates in clock map table
ASoC: rt5677: correct mismatch widget name
ASoC: rt5640: Do not allow regmap to use bulk read-write operations
ASoC: tegra: Fix typo in include guard
ASoC: da732x: Fix typo in include guard
ASoC: core: fix .info for SND_SOC_BYTES_TLV
ASoC: rcar: Use && instead of & for boolean expressions
ASoC: Use dev_set_name() instead of init_name
ASoC: axi: Fix ADI AXI SPDIF specification
add the following IDs
USB_PID_PCTV_78E (0x025a) for PCTV 78e
USB_PID_PCTV_79E (0x0262) for PCTV 79e
For these it9135 devices.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
IT9135 RF tuner clock is coming from demodulator. We need enable it
early in demod init, before any tuner I/O. Currently it is enabled
by tuner driver itself, but it is too late and performance will be
reduced as some registers are not updated correctly. Clock is
disabled automatically when demod is put onto sleep.
Cc: <stable@vger.kernel.org> # v3.15+
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That register is needed to program very first in order to operate
correctly.
[crope@iki.fi: returned sequence back, removed sleep, moved reg
write earlier to prevent populating tuner ops in case of failure]
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We should not select SPI bus when sub-driver auto-select is
selected. That option is meant for auto-selecting all possible
ancillary drivers used for selected board driver. Ancillary
drivers should define needed dependencies itself.
I2C and I2C_MUX are still selected here for a reason described on
commit 347f7a3763
Reverts commit e4462ffc16
Reported-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add the Altera SDRAM EDAC bindings and device tree changes to the Altera SoC
project.
There was a discussion thread on whether this driver should be an mfd driver
or just make use of syscon, which is already a mfd. Ultimately, the
decision to use a simple syscon interface was reached.[1]
[1] https://lkml.org/lkml/2014/7/30/514
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
[dinguyen] cleaned-up commit header and remove version history.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This patch adds a /memreserve/ section to reserve the first 4K for future
use by the system. One possible use-case is trampoline code used to bring
secondary cores online.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
---
v3: Update commit message based on Mark Rutland's comment
v2: Add a comment in the dts files
Revision D of the SOCFGPA devkit has a GPIO line used for SD/MMC card detect.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
commit [2755e187 dts: socfpga: Add DTS entry for adding the stmmac glue
layer for stmmac.] added an extra ethernet alias in the ArriaV devkit
board file. This patch removes it.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
dw-mmc
dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
drivers/media/pci/tw68/tw68-core.c:72:22: warning: symbol 'tw68_pci_tbl' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Refactor and clean up the tw68 driver. It's now using the proper
V4L2 core frameworks.
Tested with my Techwell tw6805a and tw6816 grabber boards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This tw68 driver has been out-of-tree for many years on gitorious:
https://gitorious.org/tw68/tw68-v2.
This copies that code to the kernel as a record of that original code.
Note that William Brack's email address in these sources is no longer
valid and I have not been able to contact him. However, all the code is
standard GPL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tired of copy/pasting things around.
v2: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Johan writes:
USB-serial fixes for v3.17-rc4
These updates add back some PIDs that were lost in a recent revert and add a
couple of new ones. Included is also an update to how the sierra driver binds
its interfaces in order to avoid binding CDC interfaces.
Signed-off-by: Johan Hovold <johan@kernel.org>
This fixes a boot hang observed when the bootloader already enabled the
PCIe link for its own use. The fundamental problem is that Freescale
forgot to wire up the core reset, so software doesn't have a sane way to
get the core into a defined state.
According to the DW PCIe core reference manual, configuration of the core
may only happen when the LTSSM is disabled, so this is one of the first
things we need to do. Apparently this isn't safe to do when the LTSSM is in
any state other than "detect" as we observe an instant machine hang when
trying to do so while the link is already up.
As a workaround, force LTSSM into detect state right before hitting the
disable switch. There is still a race window because the LTSSM may
transition out of "detect" before we can disable it, but it's the best
we can do for now.
[bhelgaas: mention race window]
Link: http://lkml.kernel.org/r/1406830565-23450-3-git-send-email-l.stach@pengutronix.de
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
The new version of the macro does a few things better:
- protect the arguments,
- only evaluate the arguments once,
- check that the arguments are of the same type,
Change LC_FREQ_2K to be a unsigned 64bit constant and removed the '()'
from the caller as a result.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani wanted some comments to explain why we call certain vdd on/off
functions in certain places.
v2: Make the comments more thorough (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to turn the DP port off after the pipe, otherwise the pipe won't
turn off properly on certain pch platforms at least (happens on my ILK for
example). This also matches the BSpec modeset sequence better. We still
don't match the spec exactly though (eg. audio disable should happen
much earlier), but at last this eliminates the nasty
wait_for_pipe_off() timeouts.
We already did the port disable after the pipe for VLV/CHV and for CPU
eDP.
For g4x leave the port disable where it is since that matches the
modeset sequence in the documentation and I don't have a suitable
machine to test if the other order would work.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec says we should enable the DP port before enabling panel power,
and that the port must be enabled with training pattern 1. Do so.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV the panel power sequencer may need to be "kicked" a bit to
lock onto the new port, and that needs to happen before any aux
transfers are attempted if we want the aux transfers to actaully
succeed. So turn on panel power (part of the "kick") before aux
transfers (DPMS_ON + link training).
This also matches the documented modeset sequence better for pch
platforms. The documentation doesn't explicitly state anything about the
DPMS or link training DPCD writes, but the panel power on step is
always listed before link training is mentioned.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=70117
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to make sure we find the power sequencer that the BIOS used
by first looking for one which has the panel power enabled, then
fall back to one with VDD force bit enabled, and finally look at
just the port select bits. This should make us pick the correct
power sequencer when the BIOS has already enabled the panel.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Shorten the vlv_intial_pps_pipe to make lines fit into 80
chars.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power sequencer loses its state when the disp2d power well is down.
Clear the dev_priv->pps_pipe tracking so that the power sequencer state
gets reinitialized the next time it's needed.
v2: Fix the pps_mutex vs. power_domain mutex deadlock by taking power
domain reference first
v3: Rename from edp_pps_(un)lock() to just pps_(un)lock() for the future,
update due to backlight code changes
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mark Brown