The Broadcom bcm43xx sdio devices are fullmac devices that may be
integrated in ARM platforms. Currently, the brcmfmac driver for
these devices support use of platform data. This patch specifies
the bindings that allow this platform data to be expressed in the
devicetree.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[hdegoede@redhat.com: drop clk / reg_on gpio handling, as there is no consensus
on how to handle this yet]
[hdegoede@redhat.com: move from bindings/staging to bindings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.17 pull request
This is the NFC pull request for 3.17.
This is a rather quiet one, we have:
- A new driver from ST Microelectronics for their NCI ST21NFCB,
including device tree support.
- p2p support for the ST21NFCA driver
- A few fixes an enhancements for the NFC digital layer"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
APM X-Gene SoC AHCI SATA Host controller driver requires
some correction of Phy Control OOB timing for the
COMINIT/COMWAKE parameters to correctly interoperate with
different kinds of disks.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As per SATA IO specification, when Host sends HOLD, the device takes
about 20DW latency to reply to HOLDA. In some case, device doesn't
response to HOLDA over 20DW and causes FIFO goes into over flow
condition. Due to this condition, device enumerations fails with
those devices. This patch adjust the watermark FIFO by increasing
the FIFO depth from 0x16(default) to 0x30 to address this issue.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fix sparse warnings in hid-huion.c by using correct buffer type for
retrieved string descriptor.
The warnings in question were:
drivers/hid/hid-huion.c:144:44: sparse: cast to restricted __le16
drivers/hid/hid-huion.c:145:44: sparse: cast to restricted __le16
drivers/hid/hid-huion.c:146:51: sparse: cast to restricted __le16
drivers/hid/hid-huion.c:147:30: sparse: cast to restricted __le16
Reported-by: fengguang.wu@intel.com
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Arvind Kumar <arvindkumar@vmware.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When a call to request_irq() failed pm8001_setup_msix()
still returns the success. This udate fixes the described
misbehaviour.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There is no need to call pci_disable_msix() in case
the previous call to pci_enable_msix() failed
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Function pci_enable_msix() should not be called in case
it threw a negative errno from a previous call.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: "Suma Ramars (sramars)" <sramars@cisco.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds a mount option, nobarrier, in f2fs.
The assumption in here is that file system keeps the IO ordering, but
doesn't care about cache flushes inside the storages.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
pkcs7_request_asymmetric_key() and x509_request_asymmetric_key() do the same
thing, the latter being a copy of the former created by the IMA folks, so drop
the PKCS#7 version as the X.509 location is more general.
Whilst we're at it, rename the arguments of x509_request_asymmetric_key() to
better reflect what the values being passed in are intended to match on an
X.509 cert.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Current rsnd driver is using regmap and regmap_field.
It used original regmap bus which is
single regmap instance for multi register mapping.
This patch modifies it to use regmap_mmio bus,
and tidyuped probe method
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
According to the spec, the definition of TDM and ONELINE_24 for
CS42XX8_INTF_DAC and CS42XX8_INTF_ADC is wrong. correct them and enable
SND_SOC_DAIFMT_DSP_A support.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
To make the interrupt safe if it happens to be called before the card is
ready, we use regmap read/write in the interrupt handler. Also, we try to
prevent the interrupt happen before the card is ready by enabling codec's
IRQ in the ASoC probe.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
On LPAE, each level 1 (pgd) page table entry maps 1GiB, and the level 2
(pmd) entries map 2MiB.
When the identity mapping is created on LPAE, the pgd pointers are copied
from the swapper_pg_dir. If we find that we need to modify the contents
of a pmd, we allocate a new empty pmd table and insert it into the
appropriate 1GB slot, before then filling it with the identity mapping.
However, if the 1GB slot covers the kernel lowmem mappings, we obliterate
those mappings.
When replacing a PMD, first copy the old PMD contents to the new PMD, so
that we preserve the existing mappings, particularly the mappings of the
kernel itself.
[rewrote commit message and added code comment -- rmk]
Fixes: ae2de10173 ("ARM: LPAE: Add identity mapping support for the 3-level page table format")
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds basic DT bindings for the PL11x CLCD cells
and make their fbdev driver use them.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Merge "omap n900 regression fix for v3.16 rc series" from Tony Lindgren:
Minimal regression fix for n900 display that got broken with
enabling of twl4030 PM features. Turns out more work is needed
before we can enable twl4030 PM on n900.
I did not notice this earlier as I have my n900 in a rack
and the display did not get enabled for device tree based booting
until for v3.16.
* tag 'omap-for-v3.16/n900-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert enabling of twl configuration for n900
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Modify OMAP PLL rate rounding function to round to the exact rate requested
or the next one below it. This is intended to resolve some DSS problems.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/clock-b-v3.17/20140725061121/
If init_mm.brk is not section aligned, the LPAE fixup code will miss
updating the final PMD. Fix this by aligning map_end.
Fixes: a77e0c7b27 ("ARM: mm: Recreate kernel mappings in early_paging_init()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The OMAP3 ISP driver was the only user of the OMAP IOVMM API. Now that
is has been ported to the DMA API, remove the unused virtual memory
manager.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Ignore Jabra GN9350E HID interface. USB audio is working nicely, but
registering as HID blocks USB mouse buttons. Since special userspace programs
are needed we will avoid attaching usbhid drivers in general.
Signed-off-by: Patrick Plattes <patrick@erdbeere.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Print sequence number, AMSDU_MORE flag and AC when additional
debug enabled in RX path. This is usefull for debugging purpose.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A-MSDU 4addr frames weren't reconstructed properly
and in some cases this resulted in a warning:
br0: received packet on wlan0.sta1 with own address as source address
Since this was only related to A-MSDU it would
trigger when more intense traffic was generated.
Reported-by: Vu Hai NGUYEN <vh.nguyen@actiasodielec.fr>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cp2112 supports single I2C read/write transactions. It can't combine I2C
transactions.
Add master_xfer, using similar code flow as for smbus_xfer.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On composite HID devices there may be multiple HID devices on separate interfaces, but hid-rmi
should only bind to the mouse interface. One example is the Dell Venue 11 Pro's keyboard dock
which contains a composite USB device with a HID touchpad and HID keyboard on separate intefaces.
Since the USB Vendor ID is Synaptic's, hid-core is currently trying to bind hid-rmi to all\of
the HID devices. This patch ensures that hid-rmi only binds to the mouse interface.
related bug:
https://bugzilla.kernel.org/show_bug.cgi?id=80091
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is possible that the hid-rmi driver could get loaded onto a device which does not have the
expected report ids. This should not happen because it would indicate that the hid-rmi driver is
not compatible with that device. However, if it does happen it should return an error from probe
instead of dereferencing a null pointer.
related bug:
https://bugzilla.kernel.org/show_bug.cgi?id=80091
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for both ThinkPad Compact Bluetooth Keyboard with
TrackPoint and ThinkPad Compact USB Keyboard with TrackPoint.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Ensure all tpkbd specifics are within a postfixed function, the
main functions for the driver should just switch to the appropriate
function depending on product ID. Given this, we can add extra devices
by including extra postfixed functions.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rename module and all functions within so we can add support for other
keyboards in the same file. Rename the _tp postfix to _tpkbd, to
signify functions relevant to the TP USB keyboard.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add handling of Huion tablets with UC-Logic vendor ID, but the same
product ID to hid-huion driver. A Huion H580 was seen using it.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Switch to generating tablet pen report descriptor from a template and
parameters retrieved from string descriptor 0x64.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't ignore non pen-reporting interfaces as they may be used by some
models reusing the same product ID.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use word "tablet" in identifiers and comments instead of referring to specific
Huion tablet model name, as the product ID is used by at least several tablet
models.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I am using a USB keyborad that give me "usb_submit_urb(ctrl) failed: -1" error
when I plugin it. and I need to wait for 10s for this device to be ready.
By adding this quirks, the usb keyborad is usable right after plugin
Signed-off-by: Wangzhao Cai <microcaicai@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, the i2c-hid driver does not call the suspend, resume, and
reset_resume callbacks in the hid_driver struct when those events occur.
This means that HID drivers for i2c-hid devices will not be able to execute
commands which may be needed during suspend or resume. One example is when a
touchpad using the hid-multitouch driver gets reset by i2c-hid coming out of
resume. Since the reset_resume callback never gets called the device is never
put back into the correct input mode. This patch calls the suspend and resume
callbacks and tries to duplicate the functionality of the usb-hid driver.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Vincent Huang <vincent.huang@tw.synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Userspace tools may use hidraw to perform operations on the device from userspace while
hid-rmi is bound to the device. This can cause hid-rmi to print error messages when its
->raw_event() callback gets called as the reports pass through the HID stack. In this case
receiving responses which were not initiated by hid-rmi is not actually an error so the resulting
error messages are incorrect and misleading. This patch changes the log messages to debug so
that the messages can be turned on in the event that there is a problem and there is not
a userspace tool running.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are additional queries which are optional and may not be present
depending on the configuration of the firmware. Knowing which queries are
present is needed to properly compute the address of Query 12 and all
subsequent queries. Additional bits in Query 1 are used to indicate the
presence of these optional queries.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>