The memory are mapped using of_ioremap() which is
an indication this is sbus memory.
Shift all uses of inb/outb to the sbus variants.
The inb/outb methods uses ASI_PHYS_BYPASS_EC_E_L,
whereas sbus_ variants uses ASI_PHYS_BYPASS_EC_E.
The difference is if the reads/writes are done in
native or little endian.
But for byte reads/writes there is no difference
so this does not matter for inb/outb - and this
driver only uses the byte variants.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
/dev/mdesc on Linux does not support reading arbitrary number
of bytes and seeking while /dev/mdesc on Solaris does. This
causes tools that work on Solaris to break on Linux. This patch
adds these two capabilities to /dev/mdesc.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since unaligned_panic() takes a literal string, make sure it can never
accidentally be used as a format string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flipping a bit doesn't need four lines of code; and gcc seems to
actually generate two branches.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. The header file is added to make the devm function explicitly
available.
The following Coccinelle semantic patch was used for making a part of
the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds sparc RAM to /proc/iomem. It also identifies the
code, data and bss regions of the kernel.
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MEDIA_SDR_SUPPORT and I2C_MUX are needed for rtl2832_sdr.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 0ba2aeb6da
(v4l2-ctrls: increase internal min/max/step/def to 64 bit)
changes v4l2 controls to 64-bit. Driver it not working on 32-bit
arch as it uses directly control 'step' which is changed to 64-bit.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/built-in.o: In function `isp_video_open':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1253: undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `omap3isp_video_init':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1344: undefined reference to `vb2_dma_contig_init_ctx'
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1350: undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `omap3isp_video_cleanup':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1381: undefined reference to `vb2_dma_contig_cleanup_ctx'
make: *** [vmlinux] Error 1
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
this patch fixes following sparse warning,
dm365_resizer.c:223:1: warning: symbol 'resizer_calculate_resize_ratios' was not declared. Should it be static?
dm365_resizer.c:313:5: warning: symbol 'resizer_configure_output_win' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch fixes following checkpatch warning,
media/davinci_vpfe/dm365_ipipe.c:1271: WARNING: Missing a blank line after declarations
media/davinci_vpfe/dm365_ipipe.c:1313: WARNING: Missing a blank line after declarations
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This switches all register accesses to use regmap. It allows to
use the regmap cache, tracing, and debug register dump facilities,
and removes the need to open code read-modify-writes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since (min_row_time - crop->width) can be negative, we have to do a signed
comparison here. Otherwise max_t casts the negative value to unsigned int
and sets min_hblank to that invalid value.
Cc: stable@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Regression fix:
V4L2_PIX_FMT_PRIV_MAGIC should only be set for the VIDEO_CAPTURE and
VIDEO_OUTPUT buffer types, and not for any others. In the case of
the win format this overwrote a pointer value that is passed in from
userspace.
Just set it for V4L2_BUF_TYPE_VIDEO_CAPTURE and OUTPUT only. Set
it before the callback is called, just as is done for try/s_fmt, and
again afterwards in case the driver zeroed it. The latter was missing
in try/s_fmt, so add it there as well. Currently it is quite likely
that drivers clear priv (that was needed for a long time), so it makes
sense to set it twice.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
V4L2_CAP_EXT_PIX_FORMAT is set for capabilities, but it needs to be set for
device_caps as well: device_caps should report all caps relevant to the
device node, and this is one of them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
V4L2_CID_BASE_LASTP1 should be V4L2_CID_LASTP1. This has probably been wrong
since the earliest days of this documentation until I did a copy-and-paste
and found out that V4L2_CID_BASE_LASTP1 doesn't actually exist :-)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If you have a maximum that is at the limit of what the type supports,
and the step is > 1, then you can get wrap-around errors since the
code assumes that the maximum that the type supports is
ctrl->maximum + ctrl->step / 2.
In practice this is always fine, but in artificially crafted ranges
you will hit this bug. Since this is core code it should just work.
This bug has always been there but since it doesn't cause problems in
practice it was never noticed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add defines for the start line numbers of each field for both
525 and 625 line formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While working with raw and sliced VBI support in several applications
I noticed that you really need to know the start linenumbers for
each video field in order to correctly convert the start line numbers
reported by v4l2_vbi_format to the line numbers used in v4l2_sliced_vbi_format.
This patch adds four defines that specify the start lines for each
field for both 525 and 625 line standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added a blank line after variable declarations where checkpatch
requested that, and removed the 'write to the FSF' paragraph,
again as requested.
This is in preparation of the move out of staging into drivers/media.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hariprasad Shenai says:
====================
Misc. fix for cxgb4 and iw_cxgb4
This patch series adds support to enchance error reporting, log detailed
warning for negative advice, support query_qp verb and advertise correct
device max attributes for iwarp.
The patches series is created against 'net-next' tree.
And includes patches on cxgb4 and iw_cxgb4 driver.
Since this patch-series contains changes which are dependent on commit id
4c2c5763 ("cxgb4/iw_cxgb4: use firmware ord/ird resource limits") of net-next
tree we would like to request this patch series to get merged via David Miller's
'net-next' tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise the actual max limits for things like qp depths, number of
qps, cqs, etc.
Clean up the queue allocation for qps and cqs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Govindarajulu Varadarajan says:
====================
enic: Display classifier filters using ethtool
This series adds ethtool support to show classifier filters added by driver.
v2:
The patch 1/2 removes the $ifdef's around the filter structure. Making it
available always. So that .get_rxnfc() can be implimented without any #ifdefs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch impliments ethtool_ops->get_rxnfc() to display the classifier
filter added by the driver.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the #ifdef CONFIG_RFS_ACCEL around the classifier filter
structures. This makes the filter structures available when CONFIG_RFS_ACCEL = n.
Introduce enic_rfs_timer_start() & enic_rfs_timer_stop() to start/stop the
timer. These two functions are nop when CONFIG_RFS_ACCEL = n.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An af_iucv stress test showed -EPIPE results for sendmsg()
calls. They are caused by quiescing a path even though it has
been already severed by peer. For IUCV transport shutdown()
consists of 2 steps:
(1) sending the shutdown message to peer
(2) quiescing the iucv path
If the iucv path between these 2 steps is severed due to peer
closing the path, the quiesce step is no longer needed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Reported-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to display the adjacent switch port's forwarding
attributes. Currently supports info on forwarding modes '802.1'
and 'rr' (reflective relay).
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antonio Quartulli says:
====================
pull request [net]: batman-adv 20140721
here you have two fixes that we have been testing for quite some time
(this is why they arrived a bit late in the rc cycle).
Patch 1) ensures that BLA packets get dropped and not forwarded to the
mesh even if they reach batman-adv within QinQ frames. Forwarding them
into the mesh means messing up with the TT database of other nodes which
can generate all kind of unexpected behaviours during route computation.
Patch 2) avoids a couple of race conditions triggered upon fast VLAN
deletion-addition. Such race conditions are pretty dangerous because
they not only create inconsistencies in the TT database of the nodes
in the network, but such scenario is also unrecoverable (unless
nodes are rebooted).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The fact that the pixelformat is using a packed RGB format has nothing
to do with the colorspace that is being used. Those are very different
things. The colorspace decides what color a triplet of RGB numbers
actually map to. E.g. a red color with values (255, 0, 0) is a different
type of red depending on the colorspace. If the original pixelformat was
e.g. YUV in colorspace REC709, then after the conversion to RGB the
colorspace is still REC709. Unless the hardware actually converted the
colorspace as well from REC709 to sRGB, but that rarely if ever happens.
Remove this incorrect comment.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the following error, which sometimes happens during the NFC data
transfer:
atmel_nand 80000000.nand: Time out to wait for interrupt: 0x00010000
atmel_nand 80000000.nand: something wrong, No XFR_DONE interrupt comes.
The root cause is that in the interrupt handler, we read the ISR but
only handle one interrupt. If more than one interrupt arrive at the same
time, then the second one will be lost.
During the NFC data transfer. Two NFC interrupts (NFC_CMD_DONE and
NFC_XFR_DONE) may come at the same time.
NFC_CMD_DONE means NFC command is sent, and NFC_XFR_DONE means NFC data
is transferred.
This patch can handle multiple NFC interrupts at the same time. During
the NFC data transfer, we need to wait for two NFC interrupts:
NFC_CMD_DONE and NFC_XFR_DONE.
Also we separate the completion initialization code to a
nfc_prepare_interrupt(), which is paired with nfc_wait_interrupt().
We call nfc_prepare_interrupt() before sending out nfc commands, to make
sure no interrupt lost.
Reported-by: Matthieu CRAPET <Matthieu.CRAPET@ingenico.com>
Tested-by: Matthieu Crapet <Matthieu.Crapet@ingenico.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The original report from Nikhil was that if data_offset > 0 and bytesused == 0,
then the check in __verify_length() would fail, even though the spec says that
if bytes_used == 0, then it will be replaced by the actual length of the
buffer.
After digging into it a bit more I realized that there were several other
things wrong:
- in __verify_length() it would use the application-provided length value
for USERPTR and the vb2 core length for other memory models, but it
should have used the application-provided length as well for DMABUF.
- in __fill_vb2_buffer() on the other hand it would replace bytesused == 0
by the application-provided length, even for MMAP buffers where the
length is determined by the vb2 core.
- in __fill_vb2_buffer() it tries to figure out if all the planes have
bytesused == 0 before it will decide to replace bytesused by length.
However, the spec makes no such provision, and it makes for convoluted
code. So just replace any bytesused == 0 by the proper length.
The idea behind this was that you could use bytesused to signal empty
planes, something that is currently not supported. But that is better
done in the future by using one of the reserved fields in strucy v4l2_plane.
This patch fixes all these issues.
Regards,
Hans
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Cc: Nikhil Devshatwar <nikhil.nd@ti.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>