OVL and BTP IRAM buffers are never used, setup the bits for
for DBK/BIT/IP usage depending on CODA version in one place.
Also, use a simple allocator function and group IRAM addresses
and size in a coda_aux_buf structure.
This is done in preparation for CODA960 support.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media fixes from Mauro Carvalho Chehab:
"A series of driver fixes:
- fix DVB-S tuning with tda1071
- fix tuner probe on af9035 when the device has a bad eeprom
- some fixes for the new si2168/2157 drivers
- one Kconfig build fix (for omap4iss)
- fixes at vpif error path
- don't lock saa7134 ioctl at driver's base core level, as it now
uses V4L2 and VB2 locking schema
- fix audio at hdpvr driver
- fix the aspect ratio at the digital timings table
- one new USB ID (at gspca_pac7302): Genius i-Look 317 webcam"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca_pac7302: Add new usb-id for Genius i-Look 317
[media] tda10071: fix returned symbol rate calculation
[media] tda10071: fix spec inversion reporting
[media] tda10071: add missing DVB-S2/PSK-8 FEC AUTO
[media] tda10071: force modulation to QPSK on DVB-S
[media] hdpvr: fix two audio bugs
[media] davinci: vpif: missing unlocks on error
[media] af9035: override tuner id when bad value set into eeprom
[media] saa7134: use unlocked_ioctl instead of ioctl
[media] media: v4l2-core: v4l2-dv-timings.c: Cleaning up code wrong value used in aspect ratio
[media] si2168: firmware download fix
[media] si2157: add one missing parenthesis
[media] si2168: add one missing parenthesis
[media] staging: tighten omap4iss dependencies
If bitrate is not set, the encoder is running in VBR mode, with the
I- and P-frame quantization parameters configured from userspace.
For the quantization parameters, 0 is a valid value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently the rotator unit is used to copy decoded frames out into buffers
provided by videobuf2. Since the CODA reports the I/P/B frame type of the
last decoded frame, and this frame will be copied out in a later device_run,
depending on display order, we have to store the frame type until such time.
This patch also adds the B-frame type.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
fc906b6d "Remove special clock usage in driver" removed
initialization of MFC special clock, arguing that there's
no need to do it explicitly, since it's one of MFC gate clock's
dependencies and gets enabled along with it. However, there's
no promise of keeping this hierarchy across Exynos SoC
releases, therefore this approach fails to provide a stable,
portable solution.
Out of all MFC versions, only v6 doesn't use special clock at all.
For other versions log a message only in case clk_get fails,
as not all the devices with the same MFC version require
initializing the clock explicitly.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Pull block fixes from Jens Axboe:
"Final block fixes for 3.16
Four small fixes that should go into 3.16, have been queued up for a
bit and delayed due to vacation and other euro duties. But here they
are. The pull request contains:
- Fix for a reported crash with shared tagging on SCSI from Christoph
- A regression fix for drbd. From Lars Ellenberg.
- Hooking up the compat ioctl for BLKZEROOUT, which requires no
translation. From Mikulas.
- A fix for a regression where we woud crash on queue exit if the
root_blkg is gone/not there. From Tejun"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: provide compat ioctl for BLKZEROOUT
blkcg: don't call into policy draining if root_blkg is already gone
drbd: fix regression 'out of mem, failed to invoke fence-peer helper'
block: don't assume last put of shared tags is for the host
Pull libata fixes from Tejun Heo:
"Late libata fixes.
The most important one is from Kevin Hao which makes sure that libata
only allocates tags inside the max tag number the controller supports.
libata always had this problem but the recent tag allocation change
and addition of support for sata_fsl which only supports queue depth
of 16 exposed the issue.
Hans de Goede agreed to become the maintainer of libahci_platform
which is under higher than usual development pressure from all the new
controllers popping up from the ARM world"
* 'for-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
drivers/ata/pata_ep93xx.c: use signed int type for result of platform_get_irq()
libata: EH should handle AMNF error condition as a media error
libata: support the ata host which implements a queue depth less than 32
MAINTAINERS: Add Hans de Goede as ahci-platform maintainer
Pull kvm fixes from Paolo Bonzini:
"These are mostly PPC changes for 3.16-new things. However, there is
an x86 change too and it is a regression from 3.14. As it only
affects nested virtualization and there were other changes in this
area in 3.16, I am not nominating it for 3.15-stable"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Check for nested events if there is an injectable interrupt
KVM: PPC: RTAS: Do byte swaps explicitly
KVM: PPC: Book3S PR: Fix ABIv2 on LE
KVM: PPC: Assembly functions exported to modules need _GLOBAL_TOC()
PPC: Add _GLOBAL_TOC for 32bit
KVM: PPC: BOOK3S: HV: Use base page size when comparing against slb value
KVM: PPC: Book3E: Unlock mmu_lock when setting caching atttribute
Pull s390 fixes from Martin Schwidefsky:
"A couple of last minute bug fixes for 3.16, including a fix for ptrace
to close a hole which allowed a user space program to write to the
kernel address space"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix restore of invalid floating-point-control
s390/zcrypt: improve device probing for zcrypt adapter cards
s390/ptrace: fix PSW mask check
s390/MSI: Use standard mask and unmask funtions
s390/3270: correct size detection with the read-partition command
s390: require mvcos facility, not tod clock steering facility
Firmware could request inspection of some
submitted tx requests. Since the callback wasn't
implemented it was possible to bleed tx msdu_ids
which could translate to tx flushing timeouts.
There's nothing ath10k can do to help firmware
with tx processing now so just report all tx
frames as already inspected to prevent firmware
from sending up inspection events and force it to
report regular tx completion indications with
discard status.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the s5p_mfc_alloc_firmware() function there are some mistakes
where the code checks whether the DMA memory is properly allocated or
not.
First of all dma_alloc_coherent() returns NULL in case of error.
The code also checked two times fw_virt_addr, ignoring
the bank2_virt pointer.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jonathan writes:
Fifth set of fixes for IIO in the 3.16 cycle.
One nasty one that has been around a long time and a couple of non compliant
ABI fixes.
* The demux code used to split out desired channels for devices that only
support reading sets of channels at one time had a bug where it was
building it's conversion tables against the wrong bitmap resulting in
it never actually demuxing anything. This is an old bug, but will be
effecting an increasing number of drivers as it is often used to avoid
some fiddly code in the individual drivers.
* bma180 and mma8452 weren't obeying the ABI wrt to units for acceleration.
Were in G rather than m/s^2. A little input check was missing from bma180
that might lead to acceptance of incorrect values. This last one is minor
but might lead to incorrect userspace code working and problems in the
future.
Merge "omap soc clean-up for v3.17 merge window" from Tony Lindgren:
SoC specific omap clean-up for v3.17 merge window:
- Changes to PRM and clock related code to help move
things to drivers
- Removal of unused ctrl module defines that no longer
are needed with things moving to .dts files and
drivers
* tag 'omap-for-v3.17/soc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: OMAP2+: clock/interface: remove some headers from clkt_iclk.c file
ARM: OMAP2+: clock/dpll: remove unused header includes from dpll3xxx.c
ARM: OMAP2+: clock/dpll: remove unused header includes from clkt_dpll.c
ARM: OMAP2+: clock/interface: add a clk_features definition for idlest value
ARM: OMAP2+: clock/dpll: add jitter correction behind clk_features
ARM: OMAP2+: clock/dpll: convert bypass check to use clk_features
ARM: OMAP2+: clock/dpll: add private API for checking if DPLL is in bypass
ARM: OMAP2+: clock: add fint values to the ti_clk_features struct
ARM: OMAP2+: clock: introduce ti_clk_features flags
ARM: OMAP4+: dpll44xx: remove cm-regbits-44xx.h and clock44xx.h includes
ARM: OMAP4+: dpll: remove cpu_is_omap44xx checks
ARM: OMAP4+: clock: remove DEFINE_CLK_OMAP_HSDIVIDER macro
ARM: OMAP4: Ctrl module register define diet
ARM: OMAP3: control: isolate control module init to its own function
ARM: OMAP3: PRM: move modem reset and iva2 idle to PRM driver
ARM: OMAP3: control: add API for setting up the modem pads
ARM: OMAP3: PRM: move PRM init code from PM core to the driver
ARM: OMAP24xx: PRM: add API for clearing wakeup status bits
ARM: OMAP3: PRM: add API for saving PRM scratchpad contents
ARM: OMAP3: PRM: add API for checking and clearing cold reset status
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Apparently iomap writes that unmask CE irqs aren't
propagated properly sometimes. Before failing try
to poll for the control response message as it may
have been delivered without an interrupt.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's possible that the controller has an individually switchable power supply.
Therefore add support to control a supplying regulator.
As this is not always the case, the regulator is requested as optional.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Calling radeon_vm_bo_find on the IB BO during CS
is illegal and can lead to an crash.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VM sizes smaller than 1GB doesn't make much sense anyway.
v2: fix typo and grammer
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
nfsd4_probe_callback kicks off some work that will eventually run
nfsd4_process_cb_update and update the session flags. In theory we
could process a following SEQUENCE call before that update happens
resulting in flags that don't accurately represent, for example, the
lack of a backchannel.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
BorisO reports that misc_register() fails often on xen. The current code
unregisters the CPU hotplug notifier in that case. If then a CPU is
offlined and onlined back again, we end up with a second timer running
on that CPU, leading to soft lockups and system hangs.
So let's leave the hotcpu notifier always registered - even if
mce_device_create failed for some cores and never unreg it so that we
can deal with the timer handling accordingly.
Reported-and-Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: http://lkml.kernel.org/r/1403274493-1371-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Borislav Petkov <bp@suse.de>
This is part of an effort to clean-up the MFD subsystem.
WARNING: Missing a blank line after declarations
+ int ret;
+ ret = i2c_add_driver(&max8925_driver);
total: 0 errors, 1 warnings, 275 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is part of an effort to clean-up the MFD subsystem.
+WARNING: line over 80 characters
+ &max77686_rtc_regmap_config);
total: 0 errors, 1 warnings, 299 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no need to print out-of-memory errors since this is already
done by the memory management subsystem which even calls dump_stack().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Error checking across the driver is mostly consistent besides
a few exceptions, so change these exceptions for consistency.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When platform data is not found an -EIO (I/O error) code is returned.
This doesn't seem to be the correct error so better return -EINVAL
(Invalid argument) which is what most drivers do in this case.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The function max77802_i2c_parse_dt_pdata() should only be called
if there isn't already platform data for the device.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When the CONFIG_OF option was not enabled, a dummy function
max77686_i2c_parse_dt_pdata() was defined since this is called
unconditionally on probe(). Just always define the real function
and conditionally call it if CONFIG_OF is enabled instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver doesn't have PM operations defined so add a suspend
and resume function handlers to allow the PMIC IRQ to wakeup
the system when it is put into a sleep state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Allwinner A23 SoC has a PRCM unit like the previous A31 SoC.
The differences are the AR100 clock can no longer be modified,
the APB0 clock has different divisors, and some clock gates are
gone.
This patch adds a compatible with a modified subdevice list for
the A23.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some drivers may be performing most of Tx/Rx
aggregation on their own (e.g. in firmware)
including AddBa/DelBa negotiations but may
otherwise require Rx reordering assistance.
The patch exports 2 new functions for establishing
Rx aggregation sessions in assumption device
driver has taken care of the necessary
negotiations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[fix endian bug]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Haswell and newer Intel CPUs have support for RTM, and in that case DR6.RTM is
not fixed to 1 and DR7.RTM is not fixed to zero. That is not the case in the
current KVM implementation. This bug is apparent only if the MOV-DR instruction
is emulated or the host also debugs the guest.
This patch is a partial fix which enables DR6.RTM and DR7.RTM to be cleared and
set respectively. It also sets DR6.RTM upon every debug exception. Obviously,
it is not a complete fix, as debugging of RTM is still unsupported.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some drivers (e.g. ath10k) report A-MSDU subframes
individually with identical seqno. The A-MPDU Rx
reorder code did not account for that which made
it practically unusable with drivers using
RX_FLAG_AMSDU_MORE because it would end up
dropping a lot of frames resulting in confusion in
upper network transport layers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sdata can't be NULL, and key being NULL is really not possible
unless the code is modified.
The sdata check made a static analyze (klocwork) unhappy because
we would get pointer to local (sdata->local) and only then check
if sdata is non-NULL.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove !key check as well]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "uptime" trace clock added in:
commit 8aacf017b0
tracing: Add "uptime" trace clock that uses jiffies
has wraparound problems when the system has been up more
than 1 hour 11 minutes and 34 seconds. It converts jiffies
to nanoseconds using:
(u64)jiffies_to_usecs(jiffy) * 1000ULL
but since jiffies_to_usecs() only returns a 32-bit value, it
truncates at 2^32 microseconds. An additional problem on 32-bit
systems is that the argument is "unsigned long", so fixing the
return value only helps until 2^32 jiffies (49.7 days on a HZ=1000
system).
Avoid these problems by using jiffies_64 as our basis, and
not converting to nanoseconds (we do convert to clock_t because
user facing API must not be dependent on internal kernel
HZ values).
Link: http://lkml.kernel.org/p/99d63c5bfe9b320a3b428d773825a37095bf6a51.1405708254.git.tony.luck@intel.com
Cc: stable@vger.kernel.org # 3.10+
Fixes: 8aacf017b0 "tracing: Add "uptime" trace clock that uses jiffies"
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
free_nested needs the loaded_vmcs to be valid if it is a vmcs02, in
order to detach it from the shadow vmcs. However, this is not
available anymore after commit 26a865f4aa (KVM: VMX: fix use after
free of vmx->loaded_vmcs, 2014-01-03).
Revert that patch, and fix its problem by forcing a vmcs01 as the
active VMCS before freeing all the nested VMX state.
Reported-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Tested-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the pm suspend/resume it is better
to disable the GPIO after the regmap_cache
setting calls so that if the call is interrupted
the new reg values will be cached and set on resume.
Also add pm_runtime_put in the remove call.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The use of _PDC is deprecated in ACPI 3.0 in favor of _OSC,
as ARM platform is supported only in ACPI 5.0 or higher version,
_PDC will not be used in ARM platform, so make Make _PDC only for
platforms with Intel CPUs.
Introduce ARCH_MIGHT_HAVE_ACPI_PDC and move _PDC related code in
ACPI processor driver into a single file processor_pdc.c, make x86
and ia64 select it when ACPI is enabled.
This patch also use pr_* to replace printk to fix the checkpatch
warning and factor acpi_processor_alloc_pdc() a little bit to
avoid duplicate pr_err() code.
Suggested-by: Robert Richter <rric@kernel.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>