Commit Graph

480699 Commits

Author SHA1 Message Date
Theodore Ts'o 85608f8e16 random: remove unneeded hash of a portion of the entropy pool
We previously extracted a portion of the entropy pool in
mix_pool_bytes() and hashed it in to avoid racing CPU's from returning
duplicate random values.  Now that we are using a spinlock to prevent
this from happening, this is no longer necessary.  So remove it, to
simplify the code a bit.

Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
2014-07-15 04:49:39 -04:00
Theodore Ts'o 91fcb532ef random: always update the entropy pool under the spinlock
Instead of using lockless techniques introduced in commit
902c098a36, use spin_trylock to try to grab entropy pool's lock.  If
we can't get the lock, then just try again on the next interrupt.

Based on discussions with George Spelvin.

Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
2014-07-15 04:49:39 -04:00
Michal Kazior 9936194437 ath10k: sanitize tx ring index access properly
The tx ring index was immediately trimmed with a
bitmask. This discarded the 0xFFFFFFFF error case
(which theoretically can happen when a device is
abruptly disconnected) and led to using an invalid
tx ring index. This could lead to memory
corruption.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-07-15 11:19:45 +03:00
Michal Kazior 2374b18684 ath10k: fix bmi exchange tx/rx race
It was possible for tx completion not to be
processed. In that case an old stack pointer was
left on copy engine tx ring. Next bmi exchange
would immediately pop it and use complete() on the
completion struct there causing corruption.

Make sure to wait for both tx and rx completions
properly.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-07-15 11:18:58 +03:00
Nikita Edward Baruzdin 5b853ec349 can: sja1000: Add support for CAN_CTRLMODE_PRESUME_ACK
SJA1000 has a self test mode (STM) which does not require
acknowledgement for the successful message transmission. In this mode a
node test is possible without any other active node on the bus.

This patch adds a possibility to set STM for SJA1000 controller through
specifying the corresponding CAN_CTRLMODE_PRESUME_ACK netlink flag.

Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-07-15 09:34:27 +02:00
Nikita Edward Baruzdin dcf9e15267 can: sja1000: Add support for CAN_CTRLMODE_LOOPBACK
This adds support for hardware loopback in SJA1000 by utilising its self
reception request (SRR) feature. Upon SRR the message is transmitted and
received simultaneously, meaning you can't have hardware loopback
without actually sending a message to the CAN bus in case of SJA1000.

Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-07-15 09:34:23 +02:00
Nikita Edward Baruzdin 4b9e1bab12 can: netlink: Add CAN_CTRLMODE_PRESUME_ACK flag
Most CAN controllers have a support for ignoring ACK absence. Some of
them refer to this feature as a self test mode (e. g. SJA1000) and some
include it as a part of a loopback mode (e. g. MCP2510).

Setting the introduced flag via netlink should make CAN controller
perform a successful transmission, even if there is no acknowledgement
(dominant ACK bit) received.

Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-07-15 09:34:19 +02:00
Nikita Edward Baruzdin f736d9985e can: netlink: Remove space before tab
Fixes the corresponing checkpatch.pl warning.

Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-07-15 09:33:57 +02:00
Lad, Prabhakar c6bf7e5f4a can: c_can: convert to use devm * api
This patch uses devm_* APIs as they are device managed and make code simpler.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-07-15 09:32:06 +02:00
Tony Lindgren 00e4e5b5b0 Merge remote-tracking branch 'roger/for-v3.17/gpmc-omap' into omap-for-v3.17/fixes-not-urgent 2014-07-15 00:24:39 -07:00
Peter Ujfalusi 3c9464ed75 ARM: DTS: omap5-uevm: Enable basic audio (McPDM <-> twl6040)
The board uses twl6040 codec connected via McPDM link. McBSP1 and McBSP2 can
be used for FM/BT.
At the same time move the pinctrl handling to the correct place - under the
corresponding nodes.
Audio connectors on the board:
Headset in/out
Stereo Line out
Stereo Line in.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-07-15 00:21:25 -07:00
Peter Ujfalusi 4b54a2cb14 ARM: DTS: omap5-uevm: Add node for twl6040 audio codec
The board uses twl6040 as audio codec. Move the corresponding  pinctrl as
well under the node.
twl6040 needs 32k clock from palams.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-07-15 00:21:25 -07:00
Peter Ujfalusi 55be2c5376 ARM: DTS: omap5-uevm: Enable palmas clk32kgaudio clock
clk32kg-audio clock is needed for twl6040 codec.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-07-15 00:21:24 -07:00
Kishon Vijay Abraham I 18dcd79db7 ARM: dts: dra7: Add dt data for PCIe controller
Added dt data for PCIe controller. This node contains dt data for
both the DRA7 part of designware controller and for the designware core.
The documention for this node can be found @ ../bindings/pci/ti-pci.txt.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-07-15 00:16:14 -07:00
Kishon Vijay Abraham I 692df0ef5a ARM: dts: dra7: Add dt data for PCIe PHY
Added dt data for PCIe PHY as a child node of ocp2scp3.
The documention for this node can be found @ ../bindings/phy/ti-phy.txt.
26.3.3 PCIe Shared PHY Subsystem Integration in vE of DRA7xx ES1.0
describes the PCIe PHY subsystem-related components integrated in the device.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-07-15 00:16:14 -07:00
Kishon Vijay Abraham I d1ff66b52d ARM: dts: dra7: Add dt data for PCIe PHY control module
Added dt data for PCIe PHY control module used by PCIe PHY.
The documention for this node can be found @ ../bindings/phy/ti-phy.txt

Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-07-15 00:16:13 -07:00
Kishon Vijay Abraham I 00b0af5b68 ARM: dts: dra7xx-clocks: Add missing clocks for second PCIe PHY instance
Added missing clocks used by second instance of PCIe PHY.
The documention for this nodes can be found @ ../bindings/clock/ti/gate.txt.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-07-15 00:16:12 -07:00
Kishon Vijay Abraham I b700f42c86 ARM: dts: dra7xx-clocks: rename pcie clocks to accommodate second PHY instance
There are two instances of PCIe PHY in DRA7xx. So renamed
optfclk_pciephy_32khz, optfclk_pciephy_clk and optfclk_pciephy_div_clk to
optfclk_pciephy1_32khz, optfclk_pciephy1_clk and optfclk_pciephy1_div_clk
respectively. This is needed for adding the clocks for second PCIe PHY
instance.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-07-15 00:16:11 -07:00
Kishon Vijay Abraham I ba5137b272 ARM: dts: dra7xx-clocks: Add missing 32KHz clocks used for PHY
Added missing 32KHz clock used by PCIe PHY.
Figure 26-19. PCIe PHY Subsystem Integration in vE of DRA7xx ES1.0 TRM shows
32KHz is used by PCIe PHY.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-07-15 00:16:11 -07:00
Keerthy 4310e90847 ARM: dts: dra7xx-clocks: Change the parent of apll_pcie_in_clk_mux to dpll_pcie_ref_m2ldo_ck
Change the parent of apll_pcie_in_clk_mux to dpll_pcie_ref_m2ldo_ck
from dpll_pcie_ref_ck.

Figure 26-22. DPLL_PCIE_REF Functional Block Diagram in vE of DRA7xx ES1.0 TRM
shows the signal name for the output of post divider (M2) is CLKOUTLDO.

Figure 26-21. PCIe PHY Clock Generator Overview shows CLKOUTLDO is used as
input to apll mux.

So the actual output of dpll is dpll_pcie_ref_m2ldo_ck which is also the input
of apll.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-07-15 00:16:10 -07:00
Keerthy 147e541369 ARM: dts: dra7xx-clocks: Add divider table to optfclk_pciephy_div clock
Add divider table to optfclk_pciephy_div clock. The 8th bit of
CM_CLKMODE_APLL_PCIE can be programmed to either 0x0 or 0x1
based on if the divider value is 0x2 or 0x1.

Figure 26-21. PCIe PHY Clock Generator Overview in vE of DRA7xx ES1.0 shows the
block diagram of Clock Generator Subsystem of PCIe PHY module. The divider
value if '1' should be programmed in order to get the correct
PCIE_PHY_DIV_GCLK frequency (2.5GHz).

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-07-15 00:16:09 -07:00
Chen-Yu Tsai df02dd828c ARM: sun8i: Add PRCM clock and reset controller nodes to the DTSI
With sun8i PRCM support available, we can add the PRCM clock and
reset controller nodes to the DTSI. Also update R_UART's clock
phandle and add it's reset control phandle.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-07-15 08:54:16 +02:00
Chen-Yu Tsai 6c1d66f0da clk: sunxi: sun6i-a31-apb0-gates: Add A23 APB0 support
This patch adds "allwinner,sun8i-a23-apb0-gates-clk", a A23 specific
compatible to the sun6i-a31-apb0-gates clock driver, along with the
gate bitmap.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-07-15 08:53:24 +02:00
Chen-Yu Tsai b72efd0f65 clk: sunxi: sun6i-apb0-gates: use bitmaps for valid gate indices
sun6i-apb0-gates uses the "clock-indices" DT property to indicate
valid gate bits or holes in between. However, the rest of sunxi
clock drivers use bitmaps for this purpose.

This patch modifies sun6i-apb0-gates to use bitmaps as well, to be
consistent with the sunxi platform. Also add the missing call to
clk_register_clkdev, so system clock lookups will work.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-07-15 08:52:11 +02:00
Johan Hedberg 3a19b6feb2 Bluetooth: Remove unnecessary params variable from process_adv_report()
The params variable was just used for storing the return value from the
hci_pend_le_action_lookup() function and then checking whether it's NULL
or not. We can simplify the code by checking the return value directly.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-07-15 08:01:19 +02:00
Chin-Ran Lo 5bf8a7481d Bluetooth: btmrvl: avoid sending data to firmware after hs_activated
We should suspend hci device and purge remaining data in tx queue
before enabling host sleep in firmware. If any data is sent to
firmware after host sleep is activated, firmware may end up
sending a TX_DONE interrupt to driver. If this interrupt gets
delivered to host while the SDIO host controller is suspending,
it may crash the system.

Conversely, in resume handler, we should resume hci device after
host sleep is de-activated.

Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-07-15 08:01:19 +02:00
Vince Bridgers 203f0801ad ARM: socfpga: Update socfpga_defconfig
CONFIG_PM=y
CONFIG_SUSPEND=y
CONFIG_MMC_UNSAFE_RESUME=y
CONFIG_DWMAC_SOCFPGA=y
CONFIG_USB=y
CONFIG_USB_DWC2=y
CONFIG_USB_DWC2_HOST=y
CONFIG_USB_DWC2_PLATFORM=y
CONFIG_FHANDLE=y
CONFIG_I2C=y
CONFIG_I2C_DESIGNWARE_CORE=y
CONFIG_I2C_DESIGNWARE_PLATFORM=y
CONFIG_I2C_CHARDEV=y
CONFIG_CAN=y
CONFIG_CAN_RAW=y
CONFIG_CAN_BCM=y
CONFIG_CAN_GW=y
CONFIG_CAN_DEV=y
CONFIG_CAN_CALC_BITTIMING=y
CONFIG_CAN_C_CAN=y
CONFIG_CAN_C_CAN_PLATFORM=y
CONFIG_WATCHDOG=y
CONFIG_DW_WATCHDOG=y
CONFIG_GPIOLIB=y
CONFIG_GPIO_SYSFS=y
CONFIG_GPIO_DWAPB=y
CONFIG_PPS=y
CONFIG_NETWORK_PHY_TIMESTAMPING=y
CONFIG_PTP_1588_CLOCK=y
CONFIG_VLAN_8021Q=y
CONFIG_VLAN_8021Q_GVRP=y
CONFIG_GARP=y
CONFIG_IPV6=y
CONFIG_HOTPLUG=y

Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Alan Tull <atull@altera.com>
Signed-off-by: Thor Thayer <tthayer@altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@altear.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-14 21:40:04 -07:00
Vince Bridgers dc8fbed5d9 ARM: socfpga: Add missing #reset-cells to socfpga device tree
add #reset-cells to socfpga.dtsi. This was missing from the
latest updates and caused the socfpga reset controller to fail
to load like so:

ffd05000.rstmgr: /soc/rstmgr@ffd05000 missing #reset-cells property
probe of ffd05000.rstmgr failed with error -22

Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-14 21:39:54 -07:00
Simon Horman a0f7e7496d ARM: shmobile: sh73a0: add CMT1 clock support for DT
This will be used when initialising CMT1 device using DT
until common clock framework support is added.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2014-07-15 13:34:17 +09:00
Simon Horman 2e11179da7 ARM: shmobile: r8a7740: add CMT1 clock support for DT
This will be used when initialising CMT1 device using DT
until common clock framework support is added.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2014-07-15 13:34:17 +09:00
Simon Horman aad64dc319 ARM: shmobile: r8a73a4: add CMT1 clock support for DT
This will be used when initialising CMT1 device using DT
until common clock framework support is added.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2014-07-15 13:34:17 +09:00
Simon Horman ef9cb75ca7 ARM: shmobile: r8a7740: add TMU clock support for DT
This will be used when initialising TMU devices using DT
until common clock framework support is added.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2014-07-15 13:34:17 +09:00
Simon Horman 0985f38d13 ARM: shmobile: r8a7778: add TMU clock support for DT
This will be used when initialising TMU devices using DT
until common clock framework support is added.

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2014-07-15 13:34:17 +09:00
Dave Airlie 85d9e14cfd Merge branch 'linux-3.16' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
deadlock fix.

* 'linux-3.16' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nouveau/therm: fix a potential deadlock in the therm monitoring code
2014-07-15 13:25:58 +10:00
Martin Peres bb78e7a12a drm/nouveau/therm: fix a potential deadlock in the therm monitoring code
Signed-off-by: Martin Peres <martin.peres@free.fr>
Tested-by: Stefan Ringel <mail@stefanringel.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2014-07-15 12:33:00 +10:00
Olivier Sobrie 8f9818af4e hso: fix deadlock when receiving bursts of data
When the module sends bursts of data, sometimes a deadlock happens in
the hso driver when the tty buffer doesn't get the chance to be flushed
quickly enough.

Remove the endless while loop in function put_rxbuf_data() which is
called by the urb completion handler.
If there isn't enough room in the tty buffer, discards all the data
received in the URB.

Cc: David Miller <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jan Dumon <j.dumon@option.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:27:34 -07:00
Olivier Sobrie 5c763edfe4 hso: remove unused workqueue
The workqueue "retry_unthrottle_workqueue" is not scheduled anywhere
in the code. So, remove it.

Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:27:34 -07:00
David S. Miller 0854a7f132 Merge branch 'amd811e-cleanups'
Varka Bhadram says:

====================
This series cleanup for AMD8111E ethernet driver

v1: fix checkpatch warnings.
v2: added new line in debug messages
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:44 -07:00
Varka Bhadram 46c73ecc61 ethernet: amd: fix 'foo* bar'
This patch fix the 'foo*' bar with 'foo *bar' and (foo*) with (foo *).

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
Varka Bhadram ba69a3d78e ethernet: amd: fix pci device ids
Normally any device ids will be above the corresponding device driver
structure. This patch moves the pci device ids and MODULE_DEVICE_TABLE()
above the pci driver structure.

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
Varka Bhadram 13a4fa43bf ethernet: amd: fix comment styles
This patch fixes the comment style issues

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
Varka Bhadram f7afbaa557 ethernet: amd: dynamic debug fixes
This patch convert printk() to netdev_dbg/info/err or dev_info/err/dbg

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
Varka Bhadram 711fec5d22 ethernet: amd: use devm_ioremap()
This patch replace ioremap() with the devm_ioremap() so that
the resource will be freed automatically with the probe failed.

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
Varka Bhadram 43519e60ef ethernet: amd: move amd111e_remove_one after probe
This patch moves the remove functionalities after the probe
so that we can see the registered and released resources properly.
Every driver follows the same concept.

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
David S. Miller 30c9e022c5 Merge branch 'sfc-next'
Shradha Shah says:

====================
sfc: Add 40G support

This patch series adds support for Solarflare 7000 series
40G Solarflare network adapters starting with the SFN7X42Q.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:11:59 -07:00
Edward Cree ac331e9483 sfc: Add 40G link capability decoding
Needed to select 40G mode on a 10G/40G capable card.

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:11:48 -07:00
Mateusz Wrzesinski 3b06a00e65 sfc: Adding PCI ID for Solarflare 7000 series 40G network adapter.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:11:48 -07:00
grmoore@altera.com d68a5c3d2d mtd: denali: use 8 bytes for READID command
The Denali NAND driver reads only 5 bytes of ID, but some Hynix and Samsung
have size parameters in the 6th byte.  As a result, the page and oob size
for a Hynix H27UAG8T2B were calculated incorrectly and the driver failed to
load.

The solution is to read 8 bytes of ID, as expected by the NAND framework.

Signed-off-by: Graham Moore <grmoore@altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-07-14 18:41:40 -07:00
Kevin Hao a152056c91 mtd/ftl: fix the double free of the buffers allocated in build_maps()
I got the following panic on my fsl p5020ds board.

  Unable to handle kernel paging request for data at address 0x7375627379737465
  Faulting instruction address: 0xc000000000100778
  Oops: Kernel access of bad area, sig: 11 [#1]
  SMP NR_CPUS=24 CoreNet Generic
  Modules linked in:
  CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-next-20140613 #145
  task: c0000000fe080000 ti: c0000000fe088000 task.ti: c0000000fe088000
  NIP: c000000000100778 LR: c00000000010073c CTR: 0000000000000000
  REGS: c0000000fe08aa00 TRAP: 0300   Not tainted  (3.15.0-next-20140613)
  MSR: 0000000080029000 <CE,EE,ME>  CR: 24ad2e24  XER: 00000000
  DEAR: 7375627379737465 ESR: 0000000000000000 SOFTE: 1
  GPR00: c0000000000c99b0 c0000000fe08ac80 c0000000009598e0 c0000000fe001d80
  GPR04: 00000000000000d0 0000000000000913 c000000007902b20 0000000000000000
  GPR08: c0000000feaae888 0000000000000000 0000000007091000 0000000000200200
  GPR12: 0000000028ad2e28 c00000000fff4000 c0000000007abe08 0000000000000000
  GPR16: c0000000007ab160 c0000000007aaf98 c00000000060ba68 c0000000007abda8
  GPR20: c0000000007abde8 c0000000feaea6f8 c0000000feaea708 c0000000007abd10
  GPR24: c000000000989370 c0000000008c6228 00000000000041ed c0000000fe00a400
  GPR28: c00000000017c1cc 00000000000000d0 7375627379737465 c0000000fe001d80
  NIP [c000000000100778] .__kmalloc_track_caller+0x70/0x168
  LR [c00000000010073c] .__kmalloc_track_caller+0x34/0x168
  Call Trace:
  [c0000000fe08ac80] [c00000000087e6b8] uevent_sock_list+0x0/0x10 (unreliable)
  [c0000000fe08ad20] [c0000000000c99b0] .kstrdup+0x44/0x90
  [c0000000fe08adc0] [c00000000017c1cc] .__kernfs_new_node+0x4c/0x130
  [c0000000fe08ae70] [c00000000017d7e4] .kernfs_new_node+0x2c/0x64
  [c0000000fe08aef0] [c00000000017db00] .kernfs_create_dir_ns+0x34/0xc8
  [c0000000fe08af80] [c00000000018067c] .sysfs_create_dir_ns+0x58/0xcc
  [c0000000fe08b010] [c0000000002c711c] .kobject_add_internal+0xc8/0x384
  [c0000000fe08b0b0] [c0000000002c7644] .kobject_add+0x64/0xc8
  [c0000000fe08b140] [c000000000355ebc] .device_add+0x11c/0x654
  [c0000000fe08b200] [c0000000002b5988] .add_disk+0x20c/0x4b4
  [c0000000fe08b2c0] [c0000000003a21d4] .add_mtd_blktrans_dev+0x340/0x514
  [c0000000fe08b350] [c0000000003a3410] .mtdblock_add_mtd+0x74/0xb4
  [c0000000fe08b3e0] [c0000000003a32cc] .blktrans_notify_add+0x64/0x94
  [c0000000fe08b470] [c00000000039b5b4] .add_mtd_device+0x1d4/0x368
  [c0000000fe08b520] [c00000000039b830] .mtd_device_parse_register+0xe8/0x104
  [c0000000fe08b5c0] [c0000000003b8408] .of_flash_probe+0x72c/0x734
  [c0000000fe08b750] [c00000000035ba40] .platform_drv_probe+0x38/0x84
  [c0000000fe08b7d0] [c0000000003599a4] .really_probe+0xa4/0x29c
  [c0000000fe08b870] [c000000000359d3c] .__driver_attach+0x100/0x104
  [c0000000fe08b900] [c00000000035746c] .bus_for_each_dev+0x84/0xe4
  [c0000000fe08b9a0] [c0000000003593c0] .driver_attach+0x24/0x38
  [c0000000fe08ba10] [c000000000358f24] .bus_add_driver+0x1c8/0x2ac
  [c0000000fe08bab0] [c00000000035a3a4] .driver_register+0x8c/0x158
  [c0000000fe08bb30] [c00000000035b9f4] .__platform_driver_register+0x6c/0x80
  [c0000000fe08bba0] [c00000000084e080] .of_flash_driver_init+0x1c/0x30
  [c0000000fe08bc10] [c000000000001864] .do_one_initcall+0xbc/0x238
  [c0000000fe08bd00] [c00000000082cdc0] .kernel_init_freeable+0x188/0x268
  [c0000000fe08bdb0] [c0000000000020a0] .kernel_init+0x1c/0xf7c
  [c0000000fe08be30] [c000000000000884] .ret_from_kernel_thread+0x58/0xd4
  Instruction dump:
  41bd0010 480000c8 4bf04eb5 60000000 e94d0028 e93f0000 7cc95214 e8a60008
  7fc9502a 2fbe0000 419e00c8 e93f0022 <7f7e482a> 39200000 88ed06b2 992d06b2
  ---[ end trace b4c9a94804a42d40 ]---

It seems that the corrupted partition header on my mtd device triggers
a bug in the ftl. In function build_maps() it will allocate the buffers
needed by the mtd partition, but if something goes wrong such as kmalloc
failure, mtd read error or invalid partition header parameter, it will
free all allocated buffers and then return non-zero. In my case, it
seems that partition header parameter 'NumTransferUnits' is invalid.

And the ftl_freepart() is a function which free all the partition
buffers allocated by build_maps(). Given the build_maps() is a self
cleaning function, so there is no need to invoke this function even
if build_maps() return with error. Otherwise it will causes the
buffers to be freed twice and then weird things would happen.

Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-07-14 18:41:20 -07:00
Chen Gang d0f17b64ec drivers: staging: lustre: Use 'force_die' instead of 'die' to avoid compiling issue
Some of architectures have already defined 'die' as macro, so can not
use it as declaration or definition in other modules, or it will cause
compiling issue.

So use more precise name 'force_die' (like 'wrap_bulk') instead of. And
the related error (with allmodconfig under score):

    CC [M]  drivers/staging/lustre/lustre/ptlrpc/sec.o
  drivers/staging/lustre/lustre/ptlrpc/sec.c: In function 'sptlrpc_cli_ctx_expire':
  drivers/staging/lustre/lustre/ptlrpc/sec.c:309:13: error: 'struct ptlrpc_ctx_ops' has no member named '__die'
    ctx->cc_ops->die(ctx, 0);
               ^
  drivers/staging/lustre/lustre/ptlrpc/sec.c: In function 'ctx_refresh_timeout':
  drivers/staging/lustre/lustre/ptlrpc/sec.c:594:26: error: 'struct ptlrpc_ctx_ops' has no member named '__die'
     req->rq_cli_ctx->cc_ops->die(req->rq_cli_ctx, 0);
                            ^
  make[5]: *** [drivers/staging/lustre/lustre/ptlrpc/sec.o] Error 1
  make[4]: *** [drivers/staging/lustre/lustre/ptlrpc] Error 2
  make[3]: *** [drivers/staging/lustre/lustre] Error 2
  make[2]: *** [drivers/staging/lustre] Error 2
  make[1]: *** [drivers/staging] Error 2
  make: *** [drivers] Error 2

Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-14 18:40:12 -07:00