SPEAr SOCs have some miscellaneous registers which are used to configure
peripheral.
This patch adds dt node and binding information for this block.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Cc: devicetree@vger.kernel.org
[viresh: fixed logs/cclist]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
SPEAr13xx was using virtual address space 0xFE000000 to map physical address
space 0xB3000000. But pci_remap_io uses 0xFEE00000 as virtual address and so
replace 0xFE000000 with 0xF9000000.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
[viresh: fixed logs/cclist]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
ARM based ST Microelectronics's SPEAr1310/40 platforms uses ST's phy (known as
'miphy') for PCIe and SATA. This patch adds drivers for these miphys.
This also adds proper bindings for miphys.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
[viresh: fixed logs/cclist/checkpatch warnings, broken into smaller patches]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This family of chips was long ago supported by the pre-cfi driver.
CFI code tested on several Zaurus SL-5500 (Collie) 2x16 on 32 bit bus.
Function is_LH28F640BF() mimics is_m29ew() from cmdset_0002.c
Buffer write fixes as seen in 2007 patch c/o
Anti Sullin <anti.sullin <at> artecdesign.ee>
http://comments.gmane.org/gmane.linux.ports.arm.kernel/36733
[Brian: this patch is semi-urgent, because the following patch switches
to using CFI detection for a chip which (until now) is unsupported by
the CFI driver
9218310 ARM: 8084/1: sa1100: collie: revert back to cfi_probe
]
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In commit 67a9ad9b8a ("mtd: nand: Warn the user if the selected ECC
strength is too weak"), a check was added to inform the user when the
ECC used for a NAND device is weaker than the recommended ECC
advertised by the NAND chip. However, the warning uses WARN_ON(),
which has two undesirable side-effects:
- It just prints to the kernel log the fact that there is a warning
in this file, at this line, but it doesn't explain anything about
the warning itself.
- It dumps a stack trace which is very noisy, for something that the
user is most likely not able to fix. If a certain ECC used by the
kernel is weaker than the advertised one, it's most likely to make
sure the kernel uses an ECC that is compatible with the one used by
the bootloader, and changing the bootloader may not necessarily be
easy. Therefore, normal users would not be able to do anything to
fix this very noisy warning, and will have to suffer from it at
every kernel boot. At least every time I see this stack trace in my
kernel boot log, I wonder what new thing is broken, just to realize
that it's once again this NAND ECC warning.
Therefore, this commit turns:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/thomas/projets/linux-2.6/drivers/mtd/nand/nand_base.c:4051 nand_scan_tail+0x538/0x780()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-rc3-dirty #4
[<c000e3dc>] (unwind_backtrace) from [<c000bee4>] (show_stack+0x10/0x14)
[<c000bee4>] (show_stack) from [<c0018180>] (warn_slowpath_common+0x6c/0x8c)
[<c0018180>] (warn_slowpath_common) from [<c001823c>] (warn_slowpath_null+0x1c/0x24)
[<c001823c>] (warn_slowpath_null) from [<c02c50cc>] (nand_scan_tail+0x538/0x780)
[<c02c50cc>] (nand_scan_tail) from [<c0639f78>] (orion_nand_probe+0x224/0x2e4)
[<c0639f78>] (orion_nand_probe) from [<c026da00>] (platform_drv_probe+0x18/0x4c)
[<c026da00>] (platform_drv_probe) from [<c026c1f4>] (really_probe+0x80/0x218)
[<c026c1f4>] (really_probe) from [<c026c47c>] (__driver_attach+0x98/0x9c)
[<c026c47c>] (__driver_attach) from [<c026a8f0>] (bus_for_each_dev+0x64/0x94)
[<c026a8f0>] (bus_for_each_dev) from [<c026bae4>] (bus_add_driver+0x144/0x1ec)
[<c026bae4>] (bus_add_driver) from [<c026cb00>] (driver_register+0x78/0xf8)
[<c026cb00>] (driver_register) from [<c026da5c>] (platform_driver_probe+0x20/0xb8)
[<c026da5c>] (platform_driver_probe) from [<c00088b8>] (do_one_initcall+0x80/0x1d8)
[<c00088b8>] (do_one_initcall) from [<c0620c9c>] (kernel_init_freeable+0xf4/0x1b4)
[<c0620c9c>] (kernel_init_freeable) from [<c049a098>] (kernel_init+0x8/0xec)
[<c049a098>] (kernel_init) from [<c00095f0>] (ret_from_fork+0x14/0x24)
---[ end trace 62f87d875aceccb4 ]---
Into the much shorter, and much more useful:
nand: WARNING: MT29F2G08ABAEAWP: the ECC used on your system is too weak compared to the one required by the NAND chip
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ARM based ST Microelectronics's SPEAr1310 and SPEAr1340 SOCs have onchip
designware PCIe controller. To make that usable, this patch adds a wrapper
driver based on existing designware driver.
Adds bindings for this new driver and update MAINTAINERS as well.
Cc: linux-pci@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
[viresh: fixed logs/cclist/checkpatch warnings, broken into smaller patches]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
fl_owner_t is a cookie that can store all kinds of different pointers,
so don't pretends it points to a file structure.
For now just change the typedef, but as a follow on this will allow
to get rids of lots of casts and eventually the typedef itself.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
When a vSMP Foundation box is detected, the function apic_cluster_num() counts
the number of APIC clusters found. If more than one found, a multi board
configuration is assumed, and TSC marked as unstable. This behavior is
incorrect as vSMP Foundation may use processors from single node only, attached
to memory of other nodes - and such node may have more than one APIC cluster
(typically any recent intel box has more than single APIC_CLUSTERID(x)).
To fix this, we simply remove the code which detects a vSMP Foundation box and
affects apic_is_clusted_box() return value. This can be done because later the
kernel checks by itself if the TSC is stable using the
check_tsc_sync_[source|target]() functions and marks TSC as unstable if needed.
Acked-by: Shai Fultheim <shai@scalemp.com>
Signed-off-by: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1404036068-11674-1-git-send-email-oren@scalemp.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Jonathan writes:
4th set of fixes for IIO in the 3.16 cycle
* Fix incorrect handling of the iio_event_spec mask_shared_by_type
bitmap. The point of this was to allow multiple channels to specify
elements that lead to the same sysfs attribute. A but in the handling
meant that this failed. The handling is modified to be similar to that
used for the main IIO info_mask_shared_by_type which works correclty.
* The acceleration scale factors reported by the mma8452 driver gave
accelerations in g, wherease the IIO ABI is in m/s^2. The fix simply
corrects the reported scale factors.
This resolves a number of merge issues with changes in this tree and
Linus's tree at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds DT support for the LaCie NAS d2 Network v2 (d2net_v2).
Most of the hardware characteristics are shared with the 2Big and 5Big
Network v2 boards.
- CPU: Marvell 88F6281 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- 2 SATA ports: internal and eSATA
- Gigabit ethernet: PHY Marvell 88E1116R
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 power switch
- 1 SATA LED (bi-color, blue and red)
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1404830545-15581-3-git-send-email-simon.guinot@sequanux.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The d2 Network v2 board (d2net_v2) shares a lot of hardware
characteristics with the 2Big and 5Big Network v2 boards. This patch
prepares the kirkwood-netxbig.dtsi file in order to allow to include it
from the d2net_v2 DTS file. The DT nodes only relevant for the 2Big and
5Big Network v2 boards are moved into their respective DTS files.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1404830545-15581-2-git-send-email-simon.guinot@sequanux.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Allows explicity enabling of events
Previously, events were always reported as enabled, but actually only
implicitly enabled when updating the buffer scan mode
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
only report an event as enabled if it actually is enabled
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
rename since function is used by all chips with ALERT pin, not just ad7997/8
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
writing ALERT_EN and BUSY_ALERT to the chip config register clears
pending alerts, BUSY_ALERT is cleared when reading back the register
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
an IRQ is necessary to handle the ALERT condition; without
IRQ, the IIO event interface serves no purpose
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The advantage of kcalloc is, that will prevent integer overflows
which could result from the multiplication of number of elements
and size and it is also a bit nicer to read.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ext4 bugfixes from Ted Ts'o:
"More bug fixes for ext4 -- most importantly, a fix for a bug
introduced in 3.15 that can end up triggering a file system corruption
error after a journal replay.
It shouldn't lead to any actual data corruption, but it is scary and
can force file systems to be remounted read-only, etc"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix potential null pointer dereference in ext4_free_inode
ext4: fix a potential deadlock in __ext4_es_shrink()
ext4: revert commit which was causing fs corruption after journal replays
ext4: disable synchronous transaction batching if max_batch_time==0
ext4: clarify ext4_error message in ext4_mb_generate_buddy_error()
ext4: clarify error count warning messages
ext4: fix unjournalled bg descriptor while initializing inode bitmap
The spinlock protecting the L2CAP ident number can be converted into
a mutex since the whole processing is run in a workqueue. So instead
of using a spinlock, just use a mutex here.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Jonathan writes:
3rd round of IIO new drivers, cleanups and functionality for the 3.17 cycle.
New drivers
* isl29125 digital color light sensor driver
* TAOS/AMS tcs3414 digital color sensor
Staging graduation
* ad7291 ADC driver.
New functionality
* st_sensors - device tree support and bindings
* mma8452 - device tree support
Cleanups
* Drop redundant variables in a number of drivers.
* Reorder a structure definition to ealy wiht a warning about static
not being at the beginning in the hid-sensors driver.
* Switch a few more drivers away from using explicit sampling_frequency
attribute to providing this through the core.
* Make hid_sensor_get_reporting_interval static as only used within a single
file.
* Drop a redundant check for negative values in an unsigned variable from
ad9832
* Drop some duplicate case labels in the event monitor example code.
* Use devm_ioremap_resource to simplify error handling.
* Use devm_kzalloc within the blackfin timer driver to simplify error
handling and removal.
* A number of cleanups of the ad7291 from Hartmut Knaack in response
to a patch moving it out of staging.
* Core support for the period info element about events. It has been
in the abi for a while, but not added until now to the newer handling
of information related to events.
* Add HAS_IOMEM dependency to mxs_lradc to avoid build issues when testing
enabled.