release 2489

[Taranis] New alarm when TELEMETRY lost/back

TinyApp/Common_Define.h

@@ -1,206 +0,0 @@
-
-
-/*****************************************************************************/
-#define TWI_CMD_PAGEUPDATE        	0x01	// TWI Command to program a flash page
-#define TWI_CMD_EXECUTEAPP        	0x02	// TWI Command to jump to the application program
-#define TWI_CMD_SETREAD_ADDRESS			0x03	// TWI Command to set address to read from
-#define TWI_CMD_WRITE_DATA         	0x04	// TWI Command send data to the application
-
-#define TWI_CMD_REBOOT							0x55	// TWI Command to restart back in the bootloader
-
-#define TWI_SUBCMD_SETDATETIME     	0x74	// TWI Command to set the date and time
-//#define TWI_CMD_BVERSION          	0x04	// TWI Command to get the bootloader revision identifier
-//#define TWI_CMD_ERASEFLASH        	0x05	// TWI Command to erase the entire application section of flash memory
-//#define TWI_CMD_GETERRCONDN             0x07    // TWI Command to get Error condition
-
-/*****************************************************************************/
-
-
-//#define BOOT_SETTLE_DELAY         	100	// Debounce delay for the boot pin in MCU cycles
-//#define SLAVE_ADDRESS             	0xb0	// The address identifier of this slave device on the TWI (I2C) bus
-#define INTVECT_PAGE_ADDRESS      	0x000	// The location of the start of the interrupt vector table address
-
-
-
-// Select the communcation interfacing type: TWI or USI
-/*#if defined(__ATTINY25__)   | defined(__ATTINY25V__) | \
-    defined(__ATTINY45__)   | defined(__ATTINY45V__) | \
-    defined(__ATTINY85__)   | defined(__ATTINY85V__) | \
-    defined(__ATTINY24__)   | defined(__ATTINY24A__) | \
-    defined(__ATTINY44__)   | defined(__ATTINY44A__) | \
-    defined(__ATTINY84__)   | defined(__ATTINY84A__) | \
-    defined(__ATTINY2313__) | defined(__ATTINY2313A__) | \
-    defined(__ATTINY4313__) | defined(__ATTINY4313A__) | \
-    defined(__ATTINY261__)  | defined(__ATTINY261A__) | \
-    defined(__ATTINY461__)  | defined(__ATTINY461A__) | \
-    defined(__ATTINY861__)  | defined(__ATTINY861A__) | \
-    defined(__ATTINY43U__)  | \
-    defined(__ATTINY87__)   | \
-    defined(__ATTINY167__)
-    #define __USI__  // set the communication type as USI
-#endif */
-
-#define __USI__  // set the communication type as USI
-
-
-/*#if defined(__ATTINY48__) | defined(__ATTINY88__) | \
-    defined(__ATMEGA48A__) | defined(__ATMEGA48PA__) | \
-    defined(__ATMEGA48__)
-    #define __TWI__
-#endif */     
-
-/***************************************************************/
-
-
-// Page size selection for the controller with 2K flash
-/*#if defined(__ATTINY25__)   | defined(__ATTINY25V__) | \
-    defined(__ATTINY24__)   | defined(__ATTINY24A__) | \
-    defined(__ATTINY2313__) | defined(__ATTINY2313A__) | \
-    defined(__ATTINY261__)  | defined(__ATTINY261A__)
-
-    // The flash memory page size for these devices
-    #define PAGE_SIZE 32 
-
-    // Page 32, the start of bootloader section
-    #define BOOT_PAGE_ADDRESS 0X0400  
-
-    // 2KB of flash divided by pages of size 32 bytes
-    #define TOTAL_NO_OF_PAGES  64    
-    
-    // The number of pages being used for bootloader code
-    #define BOOTLOADER_PAGES          	(TOTAL_NO_OF_PAGES - BOOT_PAGE_ADDRESS/PAGE_SIZE)	
- 
-    // For bounds check during page write/erase operation to protect the bootloader code from being corrupted
-    #define LAST_PAGE_NO_TO_BE_ERASED 	(TOTAL_NO_OF_PAGES - BOOTLOADER_PAGES)	
-#endif */
-
-// Page size selection for the controller with 4K flash
-
-/*#if defined(__ATTINY45__)   | defined(__ATTINY45V__) | \
-    defined(__ATTINY44__)   | defined(__ATTINY44A__) | \
-    defined(__ATTINY4313__) | defined(__ATTINY4313A__) | \
-    defined(__ATTINY461__)  | defined(__ATTINY461A__) | \
-    defined(__ATTINY43U__)  | \
-    defined(__ATTINY48__)   | \
-    defined(__ATMEGA48__) | \
-    defined(__ATMEGA48A__) | defined(__ATMEGA48PA__)
-          
-    // The flash memory page size for these devices
-    #define PAGE_SIZE 64      
-    
-    // Page 48, the start of bootloader section
-    #define BOOT_PAGE_ADDRESS 0X0C00   
-    
-    // 4KB of flash divided by pages of size 64 bytes
-    #define TOTAL_NO_OF_PAGES  64    
-
-    // The number of pages being used for bootloader code
-    #define BOOTLOADER_PAGES          	(TOTAL_NO_OF_PAGES - BOOT_PAGE_ADDRESS/PAGE_SIZE)	
-
-  // For bounds check during page write/erase operation to protect the bootloader code from being corrupted
-   #define LAST_PAGE_NO_TO_BE_ERASED 	(TOTAL_NO_OF_PAGES - BOOTLOADER_PAGES)	
-#endif */
-
-
-// Page size selection for the controller with 8K flash
-/*#if defined(__ATTINY85__)   | defined(__ATTINY85V__) | \
-    defined(__ATTINY84__)   | defined(__ATTINY84A__) | \
-    defined(__ATTINY861__)  | defined(__ATTINY861A__) | \
-    defined(__ATTINY87__)   | \
-    defined(__ATTINY88__)
-      
-    // The flash memory page size for these devices
-    #define PAGE_SIZE 64      
-
-    // Page 112, the start of bootloader section
-    #define BOOT_PAGE_ADDRESS 0X1C00   
-  
-    // 8KB of flash divided by pages of size 64 bytes
-    #define TOTAL_NO_OF_PAGES  128    
-    
-    // The number of pages being used for bootloader code
-    #define BOOTLOADER_PAGES          	(TOTAL_NO_OF_PAGES - BOOT_PAGE_ADDRESS/PAGE_SIZE)	
-
-//    // For bounds check during page write/erase operation to protect the bootloader code from being corrupted
-//    #define LAST_PAGE_NO_TO_BE_ERASED 	(TOTAL_NO_OF_PAGES - BOOTLOADER_PAGES)	
-//#endif*/
-
-// Page size selection for the controller with 16K flash   
-//#if defined(__ATTINY167__) 
-
-// The flash memory page size for Atiny167
-#define PAGE_SIZE 128
-
-// Page 120, the start of bootloader section
-#define BOOT_PAGE_ADDRESS 0X3800  
-
-// 16KB of flash divided by pages of size 128 bytes
-#define TOTAL_NO_OF_PAGES  128   
-
-// The number of pages being used for bootloader code
-#define BOOTLOADER_PAGES          	(TOTAL_NO_OF_PAGES - BOOT_PAGE_ADDRESS/PAGE_SIZE)	
-
-// For bounds check during page write/erase operation to protect the bootloader code from being corrupted
-#define LAST_PAGE_NO_TO_BE_ERASED 	(TOTAL_NO_OF_PAGES - BOOTLOADER_PAGES)	
-
-//#endif   
-
-
- /*****************************************************************************/
- /*****************************************************************************/
-// Select the correct Bit name of to SELFPROGRAMming
-/*#if defined(__ATTINY48__) | defined(__ATTINY48A__) | \
-    defined(__ATTINY88__) | defined(__ATTINY88A__) | \
-    defined(__ATMEGA48__) | \
-    defined(__ATMEGA48A__) | defined(__ATMEGA48PA__)
-      
-    #define SELFPROGEN     SELFPRGEN
-
-#endif */
- /*****************************************************************************/
- /*****************************************************************************/
-/*#if defined(__ATTINY25__)   | defined(__ATTINY25V__) | \
-    defined(__ATTINY45__)   | defined(__ATTINY45V__) | \
-    defined(__ATTINY85__)   | defined(__ATTINY85V__) | \
-    defined(__ATTINY87__)   | defined(__ATTINY167__) */
-    
-#define SELFPROGEN SPMEN
-
-//#endif
-
- /*****************************************************************************/
- /*****************************************************************************/
-
-
-#define WDT_TIMEOUT_8s      		( _BV( WDP3 ) | _BV( WDP0 ) )	        // Watchdog timeout for inactivity in the boot section
-#define WDT_TIMEOUT_16ms    		0	// Watchdog timeout for system reset (cleanup) before jump to application
-#define WDT_TIMEOUT_min     		WDT_TIMEOUT_16ms	                // The minimum watchdog reset time interval for jump to application
-
-
-/*****************************************************************************/
-/*****************************************************************************/
-
-#define STATUSMASK_SPMBUSY 			0x01	// The mask bit for SPM busy status code
-#define STATUSMASK_BLSCERR      0x02    // The mask bit for attempt to override bootloader section
-#define STATUSMASK_TWIABORT     0x04    // The mask bit for indicating TWI abort fn called
-#define STATUSMASK_SLTR_BUSY    0x08    // The mask bit for slave transmit
-#define STATUSMASK_SLRBAA_BUSY  0x10    // The mask bit for slave receive and ack
-#define STATUSMASK_SLRBAN_BUSY  0x20    // The mask bit for slave receive and Nack
-#define STATUSMASK_EEPROM_BUSY  0x40    // The mask bit for EEPROM busy
-#define STATUSMASK_BOOTLOADER   0x80    // The mask bit for bootloader operations
-/*****************************************************************************/
-/*****************************************************************************/
-
-#define EEMEM_ADDR_AVERSION 0x05	// The address in EEPROM where application revision identifier will be stored
-#define BVERSION 						0x96	// This bootloader revision identifier
-
-
-//static void UpdatePage (uint16_t);  
-
-#ifndef _BV
-#define _BV( __BIT_POSITION__ ) ( 1 << __BIT_POSITION__ )
-#endif
-
-//#ifdef _BV
-//#warning _BV now stands defined
-//#endif

TinyApp/Makefile

@@ -1,624 +0,0 @@
-# Hey Emacs, this is a -*- makefile -*-
-#----------------------------------------------------------------------------
-# WinAVR Makefile
-#
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device, using avrdude.
-#                Please customize the avrdude settings below first!
-#
-# make debug = Start either simulavr or avarice as specified for debugging,
-#              with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-#                   bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-
-# MCU name
-MCU = attiny167
-
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#     Typical values are:
-#         F_CPU =  1000000
-#         F_CPU =  1843200
-#         F_CPU =  2000000
-#         F_CPU =  3686400
-#         F_CPU =  4000000
-#         F_CPU =  7372800
-#         F_CPU =  8000000
-#         F_CPU = 11059200
-#         F_CPU = 14745600
-#         F_CPU = 16000000
-#         F_CPU = 18432000
-#         F_CPU = 20000000
-F_CPU = 8000000
-
-
-# Output format. (can be srec, ihex, binary)
-FORMAT = ihex
-
-
-# Target file name (without extension).
-TARGET = TinyApp
-
-
-# Object files directory
-#     To put object files in current directory, use a dot (.), do NOT make
-#     this an empty or blank macro!
-OBJDIR = .
-
-
-# List C source files here. (C dependencies are automatically generated.)
-SRC = $(TARGET).c
-
-
-# List C++ source files here. (C dependencies are automatically generated.)
-CPPSRC =
-
-
-# List Assembler source files here.
-#     Make them always end in a capital .S.  Files ending in a lowercase .s
-#     will not be considered source files but generated files (assembler
-#     output from the compiler), and will be deleted upon "make clean"!
-#     Even though the DOS/Win* filesystem matches both .s and .S the same,
-#     it will preserve the spelling of the filenames, and gcc itself does
-#     care about how the name is spelled on its command-line.
-ASRC =
-
-
-# Optimization level, can be [0, 1, 2, 3, s].
-#     0 = turn off optimization. s = optimize for size.
-#     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
-OPT = s
-
-
-# Debugging format.
-#     Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
-#     AVR Studio 4.10 requires dwarf-2.
-#     AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
-#DEBUG = stabs
-DEBUG = dwarf-2
-
-
-# List any extra directories to look for include files here.
-#     Each directory must be seperated by a space.
-#     Use forward slashes for directory separators.
-#     For a directory that has spaces, enclose it in quotes.
-EXTRAINCDIRS = c:\progs\iccv7avr\include
-
-
-# Compiler flag to set the C Standard level.
-#     c89   = "ANSI" C
-#     gnu89 = c89 plus GCC extensions
-#     c99   = ISO C99 standard (not yet fully implemented)
-#     gnu99 = c99 plus GCC extensions
-CSTANDARD = -std=gnu99
-
-
-# Place -D or -U options here for C sources
-CDEFS = -DF_CPU=$(F_CPU)UL
-
-
-# Place -D or -U options here for ASM sources
-ADEFS = -DF_CPU=$(F_CPU)
-
-
-# Place -D or -U options here for C++ sources
-CPPDEFS = -DF_CPU=$(F_CPU)UL
-#CPPDEFS += -D__STDC_LIMIT_MACROS
-#CPPDEFS += -D__STDC_CONSTANT_MACROS
-
-
-
-#---------------- Compiler Options C ----------------
-#  -g*:          generate debugging information
-#  -O*:          optimization level
-#  -f...:        tuning, see GCC manual and avr-libc documentation
-#  -Wall...:     warning level
-#  -Wa,...:      tell GCC to pass this to the assembler.
-#    -adhlns...: create assembler listing
-CFLAGS = -g$(DEBUG)
-CFLAGS += $(CDEFS)
-CFLAGS += -O$(OPT)
-CFLAGS += -funsigned-char
-CFLAGS += -funsigned-bitfields
-CFLAGS += -fpack-struct
-CFLAGS += -fshort-enums
-CFLAGS += -Wall
-CFLAGS += -Wno-main
-CFLAGS += -Wstrict-prototypes
-#CFLAGS += -mshort-calls
-#CFLAGS += -fno-unit-at-a-time
-#CFLAGS += -Wundef
-#CFLAGS += -Wunreachable-code
-#CFLAGS += -Wsign-compare
-CFLAGS += -Wa,-adlns=$(<:%.c=$(OBJDIR)/%.lst)
-CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
-CFLAGS += $(CSTANDARD)
-# Next line dumps rtl file
-#CFLAGS += -dr
-#CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
-
-
-#---------------- Compiler Options C++ ----------------
-#  -g*:          generate debugging information
-#  -O*:          optimization level
-#  -f...:        tuning, see GCC manual and avr-libc documentation
-#  -Wall...:     warning level
-#  -Wa,...:      tell GCC to pass this to the assembler.
-#    -adhlns...: create assembler listing
-CPPFLAGS = -g$(DEBUG)
-CPPFLAGS += $(CPPDEFS)
-CPPFLAGS += -O$(OPT)
-CPPFLAGS += -funsigned-char
-CPPFLAGS += -funsigned-bitfields
-CPPFLAGS += -fpack-struct
-CPPFLAGS += -fshort-enums
-CPPFLAGS += -fno-exceptions
-CPPFLAGS += -Wall
-CFLAGS += -Wundef
-#CPPFLAGS += -mshort-calls
-#CPPFLAGS += -fno-unit-at-a-time
-#CPPFLAGS += -Wstrict-prototypes
-#CPPFLAGS += -Wunreachable-code
-#CPPFLAGS += -Wsign-compare
-CPPFLAGS += -Wa,-adlns=$(<:%.cpp=$(OBJDIR)/%.lst)
-CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
-#CPPFLAGS += $(CSTANDARD)
-#CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
-
-
-#---------------- Assembler Options ----------------
-#  -Wa,...:   tell GCC to pass this to the assembler.
-#  -adhlns:   create listing
-#  -gstabs:   have the assembler create line number information; note that
-#             for use in COFF files, additional information about filenames
-#             and function names needs to be present in the assembler source
-#             files -- see avr-libc docs [FIXME: not yet described there]
-#  -listing-cont-lines: Sets the maximum number of continuation lines of hex
-#       dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
-
-
-#---------------- Library Options ----------------
-# Minimalistic printf version
-PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
-
-# Floating point printf version (requires MATH_LIB = -lm below)
-PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
-
-# If this is left blank, then it will use the Standard printf version.
-PRINTF_LIB =
-#PRINTF_LIB = $(PRINTF_LIB_MIN)
-#PRINTF_LIB = $(PRINTF_LIB_FLOAT)
-
-
-# Minimalistic scanf version
-SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
-
-# Floating point + %[ scanf version (requires MATH_LIB = -lm below)
-SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
-
-# If this is left blank, then it will use the Standard scanf version.
-SCANF_LIB =
-#SCANF_LIB = $(SCANF_LIB_MIN)
-#SCANF_LIB = $(SCANF_LIB_FLOAT)
-
-
-MATH_LIB = -lm
-
-
-# List any extra directories to look for libraries here.
-#     Each directory must be seperated by a space.
-#     Use forward slashes for directory separators.
-#     For a directory that has spaces, enclose it in quotes.
-EXTRALIBDIRS =
-
-
-
-#---------------- External Memory Options ----------------
-
-# 64 KB of external RAM, starting after internal RAM (ATmega128!),
-# used for variables (.data/.bss) and heap (malloc()).
-#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
-
-# 64 KB of external RAM, starting after internal RAM (ATmega128!),
-# only used for heap (malloc()).
-#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
-
-EXTMEMOPTS =
-
-
-
-#---------------- Linker Options ----------------
-#  -Wl,...:     tell GCC to pass this to linker.
-#    -Map:      create map file
-#    --cref:    add cross reference to  map file
-LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
-LDFLAGS += $(EXTMEMOPTS)
-LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
-LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
-LDFLAGS += -Wl,--section-start=.text=0x00D0
-LDFLAGS += -Wl,--section-start=.vectors=0x0080
-LDFLAGS += -T avr3-167.ld
-LDFLAGS += -N
-
-
-
-#---------------- Programming Options (avrdude) ----------------
-
-# Programming hardware: alf avr910 avrisp bascom bsd
-# dt006 pavr picoweb pony-stk200 sp12 stk200 stk500
-#
-# Type: avrdude -c ?
-# to get a full listing.
-#
-AVRDUDE_PROGRAMMER = stk500
-
-# com1 = serial port. Use lpt1 to connect to parallel port.
-AVRDUDE_PORT = com3
-
-AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
-#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
-
-
-# Uncomment the following if you want avrdude's erase cycle counter.
-# Note that this counter needs to be initialized first using -Yn,
-# see avrdude manual.
-#AVRDUDE_ERASE_COUNTER = -y
-
-# Uncomment the following if you do /not/ wish a verification to be
-# performed after programming the device.
-#AVRDUDE_NO_VERIFY = -V
-
-# Increase verbosity level.  Please use this when submitting bug
-# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
-# to submit bug reports.
-#AVRDUDE_VERBOSE = -v -v
-
-AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
-AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
-AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
-AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
-
-
-
-#---------------- Debugging Options ----------------
-
-# For simulavr only - target MCU frequency.
-DEBUG_MFREQ = $(F_CPU)
-
-# Set the DEBUG_UI to either gdb or insight.
-# DEBUG_UI = gdb
-DEBUG_UI = insight
-
-# Set the debugging back-end to either avarice, simulavr.
-DEBUG_BACKEND = avarice
-#DEBUG_BACKEND = simulavr
-
-# GDB Init Filename.
-GDBINIT_FILE = __avr_gdbinit
-
-# When using avarice settings for the JTAG
-JTAG_DEV = /dev/com1
-
-# Debugging port used to communicate between GDB / avarice / simulavr.
-DEBUG_PORT = 4242
-
-# Debugging host used to communicate between GDB / avarice / simulavr, normally
-#     just set to localhost unless doing some sort of crazy debugging when
-#     avarice is running on a different computer.
-DEBUG_HOST = localhost
-
-
-
-#============================================================================
-
-
-# Define programs and commands.
-SHELL = sh
-CC = avr-gcc
-OBJCOPY = avr-objcopy
-OBJDUMP = avr-objdump
-SIZE = avr-size
-AR = avr-ar rcs
-NM = avr-nm
-AVRDUDE = avrdude
-REMOVE = rm -f
-REMOVEDIR = rm -rf
-COPY = cp
-WINSHELL = cmd
-
-
-# Define Messages
-# English
-MSG_ERRORS_NONE = Errors: none
-MSG_BEGIN = -------- begin --------
-MSG_END = --------  end  --------
-MSG_SIZE_BEFORE = Size before:
-MSG_SIZE_AFTER = Size after:
-MSG_COFF = Converting to AVR COFF:
-MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
-MSG_FLASH = Creating load file for Flash:
-MSG_EEPROM = Creating load file for EEPROM:
-MSG_EXTENDED_LISTING = Creating Extended Listing:
-MSG_SYMBOL_TABLE = Creating Symbol Table:
-MSG_LINKING = Linking:
-MSG_COMPILING = Compiling C:
-MSG_COMPILING_CPP = Compiling C++:
-MSG_ASSEMBLING = Assembling:
-MSG_CLEANING = Cleaning project:
-MSG_CREATING_LIBRARY = Creating library:
-
-
-
-
-# Define all object files.
-OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
-
-# Define all listing files.
-LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
-
-
-# Compiler flags to generate dependency files.
-GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
-
-
-# Combine all necessary flags and optional flags.
-# Add target processor to flags.
-ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
-ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
-ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
-
-
-
-
-
-# Default target.
-all: begin gccversion sizebefore build sizeafter end
-
-# Change the build target to build a HEX file or a library.
-build: elf hex eep lss sym bin
-#build: lib
-
-
-elf: $(TARGET).elf
-hex: $(TARGET).hex
-bin: $(TARGET).bin
-eep: $(TARGET).eep
-lss: $(TARGET).lss
-sym: $(TARGET).sym
-LIBNAME=lib$(TARGET).a
-lib: $(LIBNAME)
-
-
-
-# Eye candy.
-# AVR Studio 3.x does not check make's exit code but relies on
-# the following magic strings to be generated by the compile job.
-begin:
-	@echo
-	@echo $(MSG_BEGIN)
-
-end:
-	@echo $(MSG_END)
-	@echo
-
-
-# Display size of file.
-HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
-ELFSIZE = $(SIZE) --mcu=$(MCU) --format=avr $(TARGET).elf
-
-sizebefore:
-	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
-	2>/dev/null; echo; fi
-
-sizeafter:
-	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
-	2>/dev/null; echo; fi
-
-
-
-# Display compiler version information.
-gccversion :
-	@$(CC) --version
-
-
-
-# Program the device.
-program: $(TARGET).hex $(TARGET).eep
-	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
-
-
-# Generate avr-gdb config/init file which does the following:
-#     define the reset signal, load the target file, connect to target, and set
-#     a breakpoint at main().
-gdb-config:
-	@$(REMOVE) $(GDBINIT_FILE)
-	@echo define reset >> $(GDBINIT_FILE)
-	@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
-	@echo end >> $(GDBINIT_FILE)
-	@echo file $(TARGET).elf >> $(GDBINIT_FILE)
-	@echo target remote $(DEBUG_HOST):$(DEBUG_PORT)  >> $(GDBINIT_FILE)
-ifeq ($(DEBUG_BACKEND),simulavr)
-	@echo load  >> $(GDBINIT_FILE)
-endif
-	@echo break main >> $(GDBINIT_FILE)
-
-debug: gdb-config $(TARGET).elf
-ifeq ($(DEBUG_BACKEND), avarice)
-	@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
-	@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
-	$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
-	@$(WINSHELL) /c pause
-
-else
-	@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
-	$(DEBUG_MFREQ) --port $(DEBUG_PORT)
-endif
-	@$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
-
-
-
-
-# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
-COFFCONVERT = $(OBJCOPY) --debugging
-COFFCONVERT += --change-section-address .data-0x800000
-COFFCONVERT += --change-section-address .bss-0x800000
-COFFCONVERT += --change-section-address .noinit-0x800000
-COFFCONVERT += --change-section-address .eeprom-0x810000
-
-
-
-coff: $(TARGET).elf
-	@echo
-	@echo $(MSG_COFF) $(TARGET).cof
-	$(COFFCONVERT) -O coff-avr $< $(TARGET).cof
-
-
-extcoff: $(TARGET).elf
-	@echo
-	@echo $(MSG_EXTENDED_COFF) $(TARGET).cof
-	$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
-
-
-
-# Create final output files (.hex, .eep) from ELF output file.
-%.hex: %.elf
-	@echo
-	@echo $(MSG_FLASH) $@
-	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
-
-%.bin: %.elf
-	$(OBJCOPY) -O binary $< $@
-
-%.eep: %.elf
-	@echo
-	@echo $(MSG_EEPROM) $@
-	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
-	--change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
-
-# Create extended listing file from ELF output file.
-%.lss: %.elf
-	@echo
-	@echo $(MSG_EXTENDED_LISTING) $@
-	$(OBJDUMP) -h -S $< > $@
-
-# Create a symbol table from ELF output file.
-%.sym: %.elf
-	@echo
-	@echo $(MSG_SYMBOL_TABLE) $@
-	$(NM) -n $< > $@
-
-
-
-# Create library from object files.
-.SECONDARY : $(TARGET).a
-.PRECIOUS : $(OBJ)
-%.a: $(OBJ)
-	@echo
-	@echo $(MSG_CREATING_LIBRARY) $@
-	$(AR) $@ $(OBJ)
-
-
-# Link: create ELF output file from object files.
-.SECONDARY : $(TARGET).elf
-.PRECIOUS : $(OBJ)
-%.elf: $(OBJ)
-	@echo
-	@echo $(MSG_LINKING) $@
-	$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
-
-
-# Compile: create object files from C source files.
-$(OBJDIR)/%.o : %.c
-	@echo
-	@echo $(MSG_COMPILING) $<
-	$(CC) -c $(ALL_CFLAGS) $< -o $@
-
-
-# Compile: create object files from C++ source files.
-$(OBJDIR)/%.o : %.cpp
-	@echo
-	@echo $(MSG_COMPILING_CPP) $<
-	$(CC) -c $(ALL_CPPFLAGS) $< -o $@
-
-
-# Compile: create assembler files from C source files.
-%.s : %.c
-	$(CC) -S $(ALL_CFLAGS) $< -o $@
-
-
-# Compile: create assembler files from C++ source files.
-%.s : %.cpp
-	$(CC) -S $(ALL_CPPFLAGS) $< -o $@
-
-
-# Assemble: create object files from assembler source files.
-$(OBJDIR)/%.o : %.S
-	@echo
-	@echo $(MSG_ASSEMBLING) $<
-	$(CC) -c $(ALL_ASFLAGS) $< -o $@
-
-
-# Create preprocessed source for use in sending a bug report.
-%.i : %.c
-	$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
-
-
-# Target: clean project.
-clean: begin clean_list end
-
-clean_list :
-	@echo
-	@echo $(MSG_CLEANING)
-	$(REMOVE) $(TARGET).bin
-	$(REMOVE) $(TARGET).hex
-	$(REMOVE) $(TARGET).eep
-	$(REMOVE) $(TARGET).cof
-	$(REMOVE) $(TARGET).elf
-	$(REMOVE) $(TARGET).map
-	$(REMOVE) $(TARGET).sym
-	$(REMOVE) $(TARGET).lss
-	$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o)
-	$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst)
-	$(REMOVE) $(SRC:.c=.s)
-	$(REMOVE) $(SRC:.c=.d)
-	$(REMOVE) $(SRC:.c=.i)
-	$(REMOVEDIR) .dep
-
-
-# Create object files directory
-$(shell mkdir $(OBJDIR) 2>/dev/null)
-
-
-# Include the dependency files.
--include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
-
-
-# Listing of phony targets.
-.PHONY : all begin finish end sizebefore sizeafter gccversion \
-build elf hex eep lss sym coff extcoff \
-clean clean_list program debug gdb-config
-
-
-
-

TinyApp/USI_TWI_Slave.h

@@ -1,174 +0,0 @@
-#ifdef __USI__
-
- /****************************************************************************/
-static void USI_TWI_SLAVE_Init( void );
-static void USI_TWI_SLAVE_Abort(void);
-static void USI_TWI_SLAVE_ReadAndProcessPacket(void);
-static void USI_TWI_SLAVE_Process_Start_Condition(void);
-void USI_TWI_SLAVE_Process_Overflow_Condition(void);
- 
-//  void prog_buffer_set_byte(uint8_t );
- 
-//   uint8_t bootloader_exit;
-uint8_t Run_boot ;
-  
- 
-#define TRUE                1
-#define FALSE               0
-
- // TWI write states.
-#define USI_TWI_SLAVE_WRITE_ADDR_HI_BYTE              (0x00)
-#define USI_TWI_SLAVE_WRITE_ADDR_LO_BYTE              (0x01)
-#define USI_TWI_SLAVE_WRITE_DATA_BYTE                 (0x02)
-  
-// TWI overflow states.
-#define USI_TWI_SLAVE_OVERFLOW_STATE_NONE             (0x00)
-#define USI_TWI_SLAVE_OVERFLOW_STATE_ACK_PR_RX        (0x01)
-#define USI_TWI_SLAVE_OVERFLOW_STATE_DATA_RX          (0x02)
-#define USI_TWI_SLAVE_OVERFLOW_STATE_ACK_PR_TX        (0x03)
-#define USI_TWI_SLAVE_OVERFLOW_STATE_PR_ACK_TX        (0x04)
-#define USI_TWI_SLAVE_OVERFLOW_STATE_DATA_TX          (0x05)
-  
-// newly added .. 
-#define USI_TWI_SLAVE_OVERFLOW_STATE_CMD_RX                 (0x06) 
-#define USI_TWI_SLAVE_OVERFLOW_STATE_DATA_TX_AVERSION       (0x07) 
-#define USI_TWI_SLAVE_OVERFLOW_STATE_DATA_TX_BVERSION       (0x08) 
-#define USI_TWI_SLAVE_OVERFLOW_STATE_DATA_TX_GETERRCONDN    (0x09) 
-  
-
-  
-//////////////////////////////////////////////////////////////////////
- //  typedef     unsigned char       uint8_t;
-
-//////////////////////////////////////////////////////////////////
-///////////////// Driver Buffer Definitions //////////////////////
-//////////////////////////////////////////////////////////////////
-// 1,2,4,8,16,32,64,128 or 256 bytes are allowed buffer sizes
-
-#define TWI_RX_BUFFER_SIZE  (16)
-#define TWI_RX_BUFFER_MASK ( TWI_RX_BUFFER_SIZE - 1 )
-
-#if ( TWI_RX_BUFFER_SIZE & TWI_RX_BUFFER_MASK )
-        #error TWI RX buffer size is not a power of 2
-#endif
-
-// 1,2,4,8,16,32,64,128 or 256 bytes are allowed buffer sizes
-
-#define TWI_TX_BUFFER_SIZE  (16)
-#define TWI_TX_BUFFER_MASK ( TWI_TX_BUFFER_SIZE - 1 )
-
-#if ( TWI_TX_BUFFER_SIZE & TWI_TX_BUFFER_MASK )
-        #error TWI TX buffer size is not a power of 2
-#endif
-
-
-
-#define USI_SLAVE_CHECK_ADDRESS                (0x00)
-#define USI_SLAVE_SEND_DATA                    (0x01)
-#define USI_SLAVE_REQUEST_REPLY_FROM_SEND_DATA (0x02)
-#define USI_SLAVE_CHECK_REPLY_FROM_SEND_DATA   (0x03)
-#define USI_SLAVE_REQUEST_DATA                 (0x04)
-#define USI_SLAVE_GET_DATA_AND_SEND_ACK        (0x05)
- 
- 
- //////////////////////////////////////////////////////////////////////////
-
- 
-/*#if defined(__ATTINY2313__) | defined(__ATTINY2313A__) | \
-    defined(__ATTINY4313__) | defined(__ATTINY4313A__) */
-
-//    #define DDR_USI             DDRB
-//    #define PORT_USI            PORTB
-//    #define PIN_USI             PINB
-//    #define PORT_USI_SDA        PORTB5
-//    #define PORT_USI_SCL        PORTB7
-//    #define PIN_USI_SDA         PINB5
-//    #define PIN_USI_SCL         PINB7
-//    #define USI_START_COND_INT  USISIF
-//    #define USI_START_VECTOR    USI_STRT_vect
-//    #define USI_OVERFLOW_VECTOR USI_OVF_vect
-//#endif
- 
-/*#if defined(__ATTINY25__) | defined(__ATTINY25V__) | \
-//    defined(__ATTINY45__) | defined(__ATTINY45V__) | \
-//    defined(__ATTINY85__) | defined(__ATTINY85V__) */
-//    #define DDR_USI             DDRB
-//    #define PORT_USI            PORTB
-//    #define PIN_USI             PINB
-//    #define PORT_USI_SDA        PORTB0
-//    #define PORT_USI_SCL        PORTB2
-//    #define PIN_USI_SDA         PINB0
-//    #define PIN_USI_SCL         PINB2
-//    #define USI_START_COND_INT  USICIF
-//    #define USI_START_VECTOR    USI_START_vect
-//    #define USI_OVERFLOW_VECTOR USI_OVF_vect 
-//#endif
-
-/*#if defined(__ATTINY24__) | defined(__ATTINY24A__) | \
-    defined(__ATTINY44__) | defined(__ATTINY44A__) | \
-    defined(__ATTINY84__) | defined(__ATTINY84V__) */
-
-//    #define DDR_USI             DDRA
-//    #define PORT_USI            PORTA
-//    #define PIN_USI             PINA
-//    #define PORT_USI_SDA        PORTA6
-//    #define PORT_USI_SCL        PORTA4
-//    #define PIN_USI_SDA         PINA6
-//    #define PIN_USI_SCL         PINA4
-//    #define USI_START_COND_INT  USISIF
-//    #define USI_START_VECTOR    USI_START_vect
-//    #define USI_OVERFLOW_VECTOR USI_OVF_vect
-//#endif
- 
-
-/*#if defined(__ATTINY261__) | defined(__ATTINY261A__) | \
-    defined(__ATTINY461__) | defined(__ATTINY461A__) | \
-     defined(__ATTINY861A__) | defined(__ATTINY861A__) */
-
-//     #define DDR_USI             DDRB
-//     #define PORT_USI            PORTB
-//     #define PIN_USI             PINB
-//     #define PORT_USI_SDA        PORTB0
-//     #define PORT_USI_SCL        PORTB2
-//     #define PIN_USI_SDA         PINB0
-//     #define PIN_USI_SCL         PINB2
-//     #define USI_START_COND_INT  USISIF
-//     #define USI_START_VECTOR    USI_START_vect
-//     #define USI_OVERFLOW_VECTOR USI_OVF_vect
-//#endif
-
-
-//#if defined(__ATTINY43U__) 
-//     #define DDR_USI             DDRB
-//     #define PORT_USI            PORTB
-//     #define PIN_USI             PINB
-//     #define PORT_USI_SDA        PORTB4
-//     #define PORT_USI_SCL        PORTB6
-//     #define PIN_USI_SDA         PINB4
-//     #define PIN_USI_SCL         PINB6
-//     #define USI_START_COND_INT  USISIF
-//     #define USI_START_VECTOR    USI_START_vect
-//     #define USI_OVERFLOW_VECTOR USI_OVF_vect
-//#endif
-
-
-//#if defined(__ATTINY87__) | defined(__ATTINY167__) 
-
-    #define DDR_USI             DDRB
-    #define PORT_USI            PORTB
-    #define PIN_USI             PINB
-    #define PORT_USI_SDA        PORTB0
-    #define PORT_USI_SCL        PORTB2
-    #define PIN_USI_SDA         PINB0
-    #define PIN_USI_SCL         PINB2
-    #define USI_START_COND_INT  USISIF
-    #define USI_START_VECTOR    USI_START_vect
-    #define USI_OVERFLOW_VECTOR USI_OVF_vect
-//#endif
-
-
-
-
-
-#endif
- 

TinyApp/avr3-167.ld

@@ -1,231 +0,0 @@
-/* Default linker script, for normal executables */
-OUTPUT_FORMAT("elf32-avr","elf32-avr","elf32-avr")
-OUTPUT_ARCH(avr:3)
-MEMORY
-{
-  text      (rx)   : ORIGIN = 0, LENGTH = 16K
-  data      (rw!x) : ORIGIN = 0x800060, LENGTH = 0xffa0
-  eeprom    (rw!x) : ORIGIN = 0x810000, LENGTH = 64K
-  fuse      (rw!x) : ORIGIN = 0x820000, LENGTH = 1K
-  lock      (rw!x) : ORIGIN = 0x830000, LENGTH = 1K
-  signature (rw!x) : ORIGIN = 0x840000, LENGTH = 1K
-}
-SECTIONS
-{
-  /* Read-only sections, merged into text segment: */
-  .hash          : { *(.hash)		}
-  .dynsym        : { *(.dynsym)		}
-  .dynstr        : { *(.dynstr)		}
-  .gnu.version   : { *(.gnu.version)	}
-  .gnu.version_d   : { *(.gnu.version_d)	}
-  .gnu.version_r   : { *(.gnu.version_r)	}
-  .rel.init      : { *(.rel.init)		}
-  .rela.init     : { *(.rela.init)	}
-  .rel.text      :
-    {
-      *(.rel.text)
-      *(.rel.text.*)
-      *(.rel.gnu.linkonce.t*)
-    }
-  .rela.text     :
-    {
-      *(.rela.text)
-      *(.rela.text.*)
-      *(.rela.gnu.linkonce.t*)
-    }
-  .rel.fini      : { *(.rel.fini)		}
-  .rela.fini     : { *(.rela.fini)	}
-  .rel.rodata    :
-    {
-      *(.rel.rodata)
-      *(.rel.rodata.*)
-      *(.rel.gnu.linkonce.r*)
-    }
-  .rela.rodata   :
-    {
-      *(.rela.rodata)
-      *(.rela.rodata.*)
-      *(.rela.gnu.linkonce.r*)
-    }
-  .rel.data      :
-    {
-      *(.rel.data)
-      *(.rel.data.*)
-      *(.rel.gnu.linkonce.d*)
-    }
-  .rela.data     :
-    {
-      *(.rela.data)
-      *(.rela.data.*)
-      *(.rela.gnu.linkonce.d*)
-    }
-  .rel.ctors     : { *(.rel.ctors)	}
-  .rela.ctors    : { *(.rela.ctors)	}
-  .rel.dtors     : { *(.rel.dtors)	}
-  .rela.dtors    : { *(.rela.dtors)	}
-  .rel.got       : { *(.rel.got)		}
-  .rela.got      : { *(.rela.got)		}
-  .rel.bss       : { *(.rel.bss)		}
-  .rela.bss      : { *(.rela.bss)		}
-  .rel.plt       : { *(.rel.plt)		}
-  .rela.plt      : { *(.rela.plt)		}
-  /* Internal text space or external memory.  */
-  .vectors :
-  {
-    *(.vectors)
-    KEEP(*(.vectors))
-  }
-  .text   :
-  {
-    /* For data that needs to reside in the lower 64k of progmem.  */
-    *(.progmem.gcc*)
-    *(.progmem*)
-    . = ALIGN(2);
-     __trampolines_start = . ;
-    /* The jump trampolines for the 16-bit limited relocs will reside here.  */
-    *(.trampolines)
-    *(.trampolines*)
-     __trampolines_end = . ;
-    /* For future tablejump instruction arrays for 3 byte pc devices.
-       We don't relax jump/call instructions within these sections.  */
-    *(.jumptables)
-    *(.jumptables*)
-    /* For code that needs to reside in the lower 128k progmem.  */
-    *(.lowtext)
-    *(.lowtext*)
-     __ctors_start = . ;
-     *(.ctors)
-     __ctors_end = . ;
-     __dtors_start = . ;
-     *(.dtors)
-     __dtors_end = . ;
-    KEEP(SORT(*)(.ctors))
-    KEEP(SORT(*)(.dtors))
-    /* From this point on, we don't bother about wether the insns are
-       below or above the 16 bits boundary.  */
-    *(.init0)  /* Start here after reset.  */
-    KEEP (*(.init0))
-    *(.init1)
-    KEEP (*(.init1))
-    *(.init2)  /* Clear __zero_reg__, set up stack pointer.  */
-    KEEP (*(.init2))
-    *(.init3)
-    KEEP (*(.init3))
-    *(.init4)  /* Initialize data and BSS.  */
-    KEEP (*(.init4))
-    *(.init5)
-    KEEP (*(.init5))
-    *(.init6)  /* C++ constructors.  */
-    KEEP (*(.init6))
-    *(.init7)
-    KEEP (*(.init7))
-    *(.init8)
-    KEEP (*(.init8))
-    *(.init9)  /* Call main().  */
-    KEEP (*(.init9))
-    *(.text)
-    . = ALIGN(2);
-    *(.text.*)
-    . = ALIGN(2);
-    *(.fini9)  /* _exit() starts here.  */
-    KEEP (*(.fini9))
-    *(.fini8)
-    KEEP (*(.fini8))
-    *(.fini7)
-    KEEP (*(.fini7))
-    *(.fini6)  /* C++ destructors.  */
-    KEEP (*(.fini6))
-    *(.fini5)
-    KEEP (*(.fini5))
-    *(.fini4)
-    KEEP (*(.fini4))
-    *(.fini3)
-    KEEP (*(.fini3))
-    *(.fini2)
-    KEEP (*(.fini2))
-    *(.fini1)
-    KEEP (*(.fini1))
-    *(.fini0)  /* Infinite loop after program termination.  */
-    KEEP (*(.fini0))
-     _etext = . ;
-  }  > text
-  .data	  : AT (ADDR (.text) + SIZEOF (.text))
-  {
-     PROVIDE (__data_start = .) ;
-    *(.data)
-    *(.data*)
-    *(.rodata)  /* We need to include .rodata here if gcc is used */
-    *(.rodata*) /* with -fdata-sections.  */
-    *(.gnu.linkonce.d*)
-    . = ALIGN(2);
-     _edata = . ;
-     PROVIDE (__data_end = .) ;
-  }  > data
-  .bss   : AT (ADDR (.bss))
-  {
-     PROVIDE (__bss_start = .) ;
-    *(.bss)
-    *(.bss*)
-    *(COMMON)
-     PROVIDE (__bss_end = .) ;
-  }  > data
-   __data_load_start = LOADADDR(.data);
-   __data_load_end = __data_load_start + SIZEOF(.data);
-  /* Global data not cleared after reset.  */
-  .noinit  :
-  {
-     PROVIDE (__noinit_start = .) ;
-    *(.noinit*)
-     PROVIDE (__noinit_end = .) ;
-     _end = . ;
-     PROVIDE (__heap_start = .) ;
-  }  > data
-  .eeprom  :
-  {
-    *(.eeprom*)
-     __eeprom_end = . ;
-  }  > eeprom
-  .fuse  :
-  {
-    KEEP(*(.fuse))
-    KEEP(*(.lfuse))
-    KEEP(*(.hfuse))
-    KEEP(*(.efuse))
-  }  > fuse
-  .lock  :
-  {
-    KEEP(*(.lock*))
-  }  > lock
-  .signature  :
-  {
-    KEEP(*(.signature*))
-  }  > signature
-  /* Stabs debugging sections.  */
-  .stab 0 : { *(.stab) }
-  .stabstr 0 : { *(.stabstr) }
-  .stab.excl 0 : { *(.stab.excl) }
-  .stab.exclstr 0 : { *(.stab.exclstr) }
-  .stab.index 0 : { *(.stab.index) }
-  .stab.indexstr 0 : { *(.stab.indexstr) }
-  .comment 0 : { *(.comment) }
-  /* DWARF debug sections.
-     Symbols in the DWARF debugging sections are relative to the beginning
-     of the section so we begin them at 0.  */
-  /* DWARF 1 */
-  .debug          0 : { *(.debug) }
-  .line           0 : { *(.line) }
-  /* GNU DWARF 1 extensions */
-  .debug_srcinfo  0 : { *(.debug_srcinfo) }
-  .debug_sfnames  0 : { *(.debug_sfnames) }
-  /* DWARF 1.1 and DWARF 2 */
-  .debug_aranges  0 : { *(.debug_aranges) }
-  .debug_pubnames 0 : { *(.debug_pubnames) }
-  /* DWARF 2 */
-  .debug_info     0 : { *(.debug_info) *(.gnu.linkonce.wi.*) }
-  .debug_abbrev   0 : { *(.debug_abbrev) }
-  .debug_line     0 : { *(.debug_line) }
-  .debug_frame    0 : { *(.debug_frame) }
-  .debug_str      0 : { *(.debug_str) }
-  .debug_loc      0 : { *(.debug_loc) }
-  .debug_macinfo  0 : { *(.debug_macinfo) }
-}

applets/ersky9x/CoProc/Makefile

@@ -1,234 +0,0 @@
-# ----------------------------------------------------------------------------
-#         ATMEL Microcontroller Software Support 
-# ----------------------------------------------------------------------------
-# Copyright (c) 2011, Atmel Corporation
-#
-# All rights reserved.
-#
-# Redistribution and use in source and binary forms, with or without
-# modification, are permitted provided that the following conditions are met:
-#
-# - Redistributions of source code must retain the above copyright notice,
-# this list of conditions and the disclaimer below.
-#
-# Atmel's name may not be used to endorse or promote products derived from
-# this software without specific prior written permission.
-#
-# DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
-# IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
-# MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
-# DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
-# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
-# LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
-# OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-# LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-# NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
-# EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-# ----------------------------------------------------------------------------
-
-#   Makefile for compiling the applet-serial flash project
-
-# Chip & board used for compilation
-# (can be overriden by adding CHIP=chip and BOARD=board to the command-line)
-CHIP  = atsam3s4
-BOARD = atsam3s4_ek
-DYN = OFF
-
-# Makefile for compiling applet-serialflash applet.
-
-ifeq (atsam3s4,$(CHIP))
-BOARD_DIR = at91sam3s4-ek
-endif
-
-ifeq (atsam3s2,$(CHIP))
-BOARD_DIR = at91sam3s2-ek
-endif
-
-ifeq (sam9g15,$(CHIP))
-BOARD =sam9g15_ek
-BOARD_DIR = at91sam9g15-ek
-endif
-
-ifeq (sam9g25,$(CHIP))
-BOARD =sam9g25_ek
-BOARD_DIR = at91sam9g25-ek
-endif
-
-ifeq (sam9g35,$(CHIP))
-BOARD =sam9g35_ek
-BOARD_DIR = at91sam9g35-ek
-endif
-
-ifeq (sam9x25,$(CHIP))
-BOARD =sam9x25_ek
-BOARD_DIR = at91sam9x25-ek
-endif
-
-ifeq (sam9x35,$(CHIP))
-BOARD =sam9x35_ek
-BOARD_DIR = at91sam9x35-ek
-endif
-
-# Defines which are the available memory targets for the AT91SAM3S-EK board.
-MEMORIES = sram
-
-# Trace level used for compilation
-# (can be overriden by adding TRACE_LEVEL=#number to the command-line)
-# TRACE_LEVEL_DEBUG      5
-# TRACE_LEVEL_INFO       4
-# TRACE_LEVEL_WARNING    3
-# TRACE_LEVEL_ERROR      2
-# TRACE_LEVEL_FATAL      1
-# TRACE_LEVEL_NO_TRACE   0
-
-# Info traces allowed by default
-TR_LEV = 0
-
-# Optimization level, put in comment for debugging
-OPTIMIZATION = -Os
-
-# Output file basename
-OUTPUT = applet-coprocessor-$(CHIP)
-
-# Output directories
-BIN = bin
-OBJ = obj
-
-#-------------------------------------------------------------------------------
-#		Tools
-#-------------------------------------------------------------------------------
-
-# Tool suffix when cross-compiling
-CROSS_COMPILE = arm-none-eabi-
-
-# Libraries
-LIBRARIES = ../../libraries
-# Chip library directory
-CHIP_LIB = $(LIBRARIES)/libchip_atsam3s
-# Board library directory
-BOARD_LIB = $(LIBRARIES)/libboard_atsam3s-ek
-# Spiflash library directory
-#SPIFLASH_LIB = $(LIBRARIES)/libspiflash
-
-# ISP directory
-ISP = ..
-# tcl_lib directory
-
-#INSTALLDIR = "../../../../tcl_lib/$(BOARD_DIR)/"
-
-LIBS = -Wl,--start-group -lgcc -lc -Wl,--end-group
-
-#-lchip_$(CHIP)_gcc_rel -lboard_$(BOARD)_gcc_rel -lspiflash_gcc_rel -Wl,--end-group
-
-LIB_PATH = -L$(CHIP_LIB)/lib
-LIB_PATH += -L$(BOARD_LIB)/lib
-#LIB_PATH += -L$(SPIFLASH_LIB)/lib
-#LIB_PATH+=-L=/lib
-#LIB_PATH+=-L=/../lib/gcc/arm-none-eabi/4.4.1
-
-# Compilation tools
-AR = $(CROSS_COMPILE)ar
-CC = $(CROSS_COMPILE)gcc
-LD = $(CROSS_COMPILE)ld
-SIZE = $(CROSS_COMPILE)size
-STRIP = $(CROSS_COMPILE)strip
-OBJCOPY = $(CROSS_COMPILE)objcopy
-GDB = $(CROSS_COMPILE)gdb
-NM = $(CROSS_COMPILE)nm
-CLSS = $(CROSS_COMPILE)objdump
-
-# Flags
-INCLUDES  = -I$(CHIP_LIB)
-INCLUDES += -I$(BOARD_LIB)
-INCLUDES += -I$(SPIFLASH_LIB)
-INCLUDES += -I$(LIBRARIES)
-
-CFLAGS += -Wall -Wchar-subscripts -Wcomment -Wformat=2 -Wimplicit-int
-CFLAGS += -Werror-implicit-function-declaration -Wmain -Wparentheses
-CFLAGS += -Wsequence-point -Wreturn-type -Wswitch -Wtrigraphs -Wunused
-CFLAGS += -Wuninitialized -Wunknown-pragmas -Wfloat-equal -Wundef
-CFLAGS += -Wshadow -Wpointer-arith -Wbad-function-cast -Wwrite-strings
-CFLAGS += -Wsign-compare -Waggregate-return -Wstrict-prototypes
-CFLAGS += -Wmissing-prototypes -Wmissing-declarations
-CFLAGS += -Wformat -Wmissing-format-attribute -Wno-deprecated-declarations
-CFLAGS += -Wpacked -Wredundant-decls -Wnested-externs -Winline -Wlong-long
-CFLAGS += -Wunreachable-code
-CFLAGS += -Wcast-align
-#CFLAGS += -Wmissing-noreturn
-#CFLAGS += -Wconversion
-
-# To reduce application size use only integer printf function.
-CFLAGS += -Dprintf=iprintf
-TRACE_LEVEL = 4
-#CFLAGS += -DTRACE_LEVEL=$(TR_LEV)
- #-DDYN_TRACES
-# -mlong-calls  -Wall
-CFLAGS += -ffunction-sections  -D$(MEMORIES)
-#CFLAGS += -DNDEBUG
-CFLAGS += -mthumb -g -gdwarf-2 $(OPTIMIZATION) $(INCLUDES) -D$(CHIP) -DTRACE_LEVEL=$(TRACE_LEVEL) -DDYN_TRACES
-ASFLAGS = -Wall -g $(OPTIMIZATION) $(INCLUDES) -D$(CHIP) -D__ASSEMBLY__
-LDFLAGS= -nostartfiles -Wl,--cref -Wl,--check-sections -Wl,--gc-sections -Wl,--entry=entry -Wl,--unresolved-symbols=report-all -Wl,--warn-common -Wl,--warn-section-align -Wl,--warn-unresolved-symbols
-LD_OPTIONAL=-Wl,--print-gc-sections -Wl,--stats
-
-#-------------------------------------------------------------------------------
-#		Files
-#-------------------------------------------------------------------------------
-
-# Directories where source files can be found
-
-VPATH += ../..
-VPATH += $(ISP)/common
-
-
-# Objects built from Asm source files
-//ASM_OBJECTS = applet_cstartup.o
-
-# Objects built from C source files
-C_OBJECTS += main.o
-C_OBJECTS += applet_cstartup.o
-
-# Append OBJ and BIN directories to output filename
-OUTPUT := $(BIN)/$(OUTPUT)
-
-#-------------------------------------------------------------------------------
-#		Rules
-#-------------------------------------------------------------------------------
-
-all: $(BIN) $(OBJ) $(MEMORIES)
-
-$(BIN) $(OBJ):
-	mkdir $@
-
-define RULES
-C_OBJECTS_$(1) = $(addprefix $(OBJ)/$(1)_, $(C_OBJECTS))
-ASM_OBJECTS_$(1) = $(addprefix $(OBJ)/$(1)_, $(ASM_OBJECTS))
-
-$(1): $$(ASM_OBJECTS_$(1)) $$(C_OBJECTS_$(1))
-	$(CC) $(LIB_PATH) $(LDFLAGS) $(LD_OPTIONAL) -T"$(BOARD_LIB)/resources/gcc/$(CHIP)/$$@_samba.lds" -Wl,-Map,$(OUTPUT).map -o $(OUTPUT).elf $$^ $(LIBS) 
-	$(NM) $(OUTPUT).elf >$(OUTPUT).elf.txt 
-	$(OBJCOPY) -O binary $(OUTPUT).elf $(OUTPUT).bin 
-	$(SIZE) $$^ $(OUTPUT).elf 
-	$(CLSS) -h -S $(OUTPUT).elf >$(OUTPUT).lss
-#	@[ -e $(INSTALLDIR) ] || mkdir $(INSTALLDIR)
-#	@cp -f $(OUTPUT).bin $(INSTALLDIR)
-	
-$$(C_OBJECTS_$(1)): $(OBJ)/$(1)_%.o: %.c Makefile $(OBJ) $(BIN)
-	$(CC) $(CFLAGS) -D$(1) -c -o $$@ $$<
-
-$$(ASM_OBJECTS_$(1)): $(OBJ)/$(1)_%.o: %.S Makefile $(OBJ) $(BIN)
-	$(CC) $(ASFLAGS) -D$(1) -c -o $$@ $$<
-
-debug_$(1): $(1)
-	$(GDB) -x "$(BOARD_LIB)/resources/gcc/$(BOARD)_$(1).gdb" -ex "reset" -readnow -se $(OUTPUT)-$(1).elf
-endef
-
-$(foreach MEMORY, $(MEMORIES), $(eval $(call RULES,$(MEMORY))))
-
-clean:
-	-del $(OBJ)\*.o $(BIN)\*.bin $(BIN)\*.elf $(BIN)\*.map
-
-# Create extended listing file from ELF output file.
-%.lss: %.elf
-	@echo
-	@echo $(MSG_EXTENDED_LISTING) $@
-	$(OBJDUMP) -h -S $< > $@

applets/ersky9x/common/applet.h

@@ -1,101 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2008, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-#ifndef APPLET_H
-#define APPLET_H
-
-/*----------------------------------------------------------------------------
- *        Global definitions
- *----------------------------------------------------------------------------*/
-
-/** Refers to the Version of SAM-BA */
-#define SAM_BA_APPLETS_VERSION  "2.11"
-
-/** Applet initialization command code.*/
-#define APPLET_CMD_INIT              0x00
-/** Applet full erase command code.*/
-#define APPLET_CMD_FULL_ERASE        0x01
-/** Applet write command code.*/
-#define APPLET_CMD_WRITE             0x02
-/** Applet read command code.*/
-#define APPLET_CMD_READ              0x03
-/** Applet read command code.*/
-#define APPLET_CMD_LOCK              0x04
-/** Applet read command code.*/
-#define APPLET_CMD_UNLOCK            0x05
-/** Applet set/clear GPNVM command code.*/
-#define APPLET_CMD_GPNVM             0x06
-/** Applet set security bit command code.*/
-#define APPLET_CMD_SECURITY          0x07
-/** Applet buffer erase command code.*/
-#define APPLET_CMD_BUFFER_ERASE      0x08
-/** Applet binary page command code for Dataflash.*/
-#define APPLET_CMD_BINARY_PAGE       0x09
-/** List Bad Blocks of a Nandflash*/
-#define APPLET_CMD_LIST_BAD_BLOCKS   0x10
-/** Tag a Nandflash Block*/
-#define APPLET_CMD_TAG_BLOCK         0x11
-/** Read the Unique ID bits (on SAM3)*/
-#define APPLET_CMD_READ_UNIQUE_ID    0x12
-/** Applet blocks erase command code. */
-#define APPLET_CMD_ERASE_BLOCKS      0x13
-/** Applet batch full erase command code. */
-#define APPLET_CMD_BATCH_ERASE       0x14
-
-/** Operation was successful.*/
-#define APPLET_SUCCESS          0x00
-/** Device unknown.*/
-#define APPLET_DEV_UNKNOWN      0x01
-/** Write operation failed.*/
-#define APPLET_WRITE_FAIL       0x02
-/** Read operation failed.*/
-#define APPLET_READ_FAIL        0x03
-/** Protect operation failed.*/
-#define APPLET_PROTECT_FAIL     0x04
-/** Unprotect operation failed.*/
-#define APPLET_UNPROTECT_FAIL   0x05
-/** Erase operation failed.*/
-#define APPLET_ERASE_FAIL       0x06
-/** No device defined in board.h*/
-#define APPLET_NO_DEV           0x07
-/** Read / write address is not aligned*/
-#define APPLET_ALIGN_ERROR      0x08
-/** Read / write found bad block*/
-#define APPLET_BAD_BLOCK        0x09
-/** Applet failure.*/
-#define APPLET_FAIL             0x0f
-
-
-/** Communication link identification*/
-#define USB_COM_TYPE            0x00
-#define DBGU_COM_TYPE           0x01
-#define JTAG_COM_TYPE           0x02
-
-#endif //#ifndef APPLET_H
-

applets/ersky9x/common/applet_cstartup.c

@@ -1,128 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2011, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-
-/*----------------------------------------------------------------------------
- *        Headers
- *----------------------------------------------------------------------------*/
-#include "board.h"
-#include "board_lowlevel.h"
-typedef void( *IntFunc )( void );
-/*----------------------------------------------------------------------------
- *        Prototypes
- *----------------------------------------------------------------------------*/
-/** Stack top */
-extern unsigned long _sstack;
-
-/** Initialize segments*/
-extern unsigned int _sidata;
-extern unsigned int _sdata, _edata;
-extern unsigned int _szero, _ezero;
-
-/** Default link entry */
-extern int main(int argc, char **argv);
-
-/** Reset entry */
-void ResetException(void) ;//__attribute__((__interrupt__));
-
-/** Exception Table */
-__attribute__((section(".isr_vector")))
-//IntFunc exception_table[] = {
-//__attribute__ ((section(".vectors"), used))
-void (* const gVectors[])(void) =
-{ 
-     /* Configure Initial Stack Pointer, using linker-generated symbols */
-    (void (*)(void))((unsigned long)&_sstack),
-//    /*(IntFunc)&*/_sstack,
-    ResetException,  /* Initial PC, set to entry point  */
-    (unsigned int) 0 /*NMIException*/,
-    (unsigned int) 0 /*HardFaultException*/,
-    (unsigned int) 0 /*MemManageException*/,
-    (unsigned int) 0 /*BusFaultException*/,
-    (unsigned int) 0 /*UsageFaultException*/,
-    0, 0, 0, 0,             /* Reserved */
-    (unsigned int) 0 /*SVCHandler*/,
-    (unsigned int) 0 /*DebugMonitor*/,
-    0,                      /* Reserved */
-    (unsigned int) 0 /*PendSVC*/,
-    (unsigned int) 0 /*SysTickHandler*/,
-    /*
-    :
-    */
-};
-
-/** Applet Mailbox and initialization flag */
-#define MAILBOX_SIZE 32
-__attribute__((section(".mailbox")))
-unsigned int mailbox[MAILBOX_SIZE];
-volatile unsigned int isInitialized = 0;
-
-/*----------------------------------------------------------------------------
- *         Reset Handler
- *----------------------------------------------------------------------------*/
-
-/**
- * \brief  This is the code that gets called on processor reset. To initialize the
- * device. And call the main() routine.
- *
- */
-__attribute__ ((section(".text"), used))
-void ResetException(void)
-{
-    unsigned int *pSrc, *pDest;
-//    { asm volatile ("cpsid i"); }
-
-	// Initialize data
-    // Zero fill bss
-    if (isInitialized == 0) {
-        pSrc = &_sidata;
-        for(pDest = &_sdata; pDest < &_edata;) {
-
-            *(pDest ++) = *(pSrc ++);
-        }
-
-        for (pDest = &_szero; pDest < &_ezero;) {
-
-            *(pDest ++) = 0;
-        }
-        isInitialized = 1;
-    }
-
-    /* LowLevelInit(); */
-
-    /* Save original SP. */
-    __asm("mov r4, sp");
-    /* Change SP to current stack point. */
-    __asm("ldr r5, =_sstack");
-    __asm(" mov sp, r5");
-    main(1, (char**)mailbox);
-    /* Restore previous SP point. */
-    __asm("mov sp, r4");
-}
-

applets/ersky9x/common/board_lowlevel.h

@@ -1,46 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2009, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-/**
- * \file
- *
- * Interface for the low-level initialization function.
- *
- */
-
-#ifndef BOARD_LOWLEVEL_H
-#define BOARD_LOWLEVEL_H
-
-/*----------------------------------------------------------------------------
- *        Exported functions
- *----------------------------------------------------------------------------*/
-extern void LowLevelInit( void ) ;
-
-#endif /* BOARD_LOWLEVEL_H */
-

applets/ersky9x/serialFlash/Makefile

@@ -1,235 +0,0 @@
-# ----------------------------------------------------------------------------
-#         ATMEL Microcontroller Software Support 
-# ----------------------------------------------------------------------------
-# Copyright (c) 2011, Atmel Corporation
-#
-# All rights reserved.
-#
-# Redistribution and use in source and binary forms, with or without
-# modification, are permitted provided that the following conditions are met:
-#
-# - Redistributions of source code must retain the above copyright notice,
-# this list of conditions and the disclaimer below.
-#
-# Atmel's name may not be used to endorse or promote products derived from
-# this software without specific prior written permission.
-#
-# DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
-# IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
-# MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
-# DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
-# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
-# LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
-# OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-# LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-# NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
-# EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-# ----------------------------------------------------------------------------
-
-#   Makefile for compiling the applet-serial flash project
-
-# Chip & board used for compilation
-# (can be overriden by adding CHIP=chip and BOARD=board to the command-line)
-CHIP  = atsam3s4
-BOARD = atsam3s4_ek
-DYN = OFF
-
-# Makefile for compiling applet-serialflash applet.
-
-ifeq (atsam3s4,$(CHIP))
-BOARD_DIR = at91sam3s4-ek
-endif
-
-ifeq (atsam3s2,$(CHIP))
-BOARD_DIR = at91sam3s2-ek
-endif
-
-ifeq (sam9g15,$(CHIP))
-BOARD =sam9g15_ek
-BOARD_DIR = at91sam9g15-ek
-endif
-
-ifeq (sam9g25,$(CHIP))
-BOARD =sam9g25_ek
-BOARD_DIR = at91sam9g25-ek
-endif
-
-ifeq (sam9g35,$(CHIP))
-BOARD =sam9g35_ek
-BOARD_DIR = at91sam9g35-ek
-endif
-
-ifeq (sam9x25,$(CHIP))
-BOARD =sam9x25_ek
-BOARD_DIR = at91sam9x25-ek
-endif
-
-ifeq (sam9x35,$(CHIP))
-BOARD =sam9x35_ek
-BOARD_DIR = at91sam9x35-ek
-endif
-
-# Defines which are the available memory targets for the AT91SAM3S-EK board.
-MEMORIES = sram
-
-# Trace level used for compilation
-# (can be overriden by adding TRACE_LEVEL=#number to the command-line)
-# TRACE_LEVEL_DEBUG      5
-# TRACE_LEVEL_INFO       4
-# TRACE_LEVEL_WARNING    3
-# TRACE_LEVEL_ERROR      2
-# TRACE_LEVEL_FATAL      1
-# TRACE_LEVEL_NO_TRACE   0
-
-# Info traces allowed by default
-TR_LEV = 0
-
-# Optimization level, put in comment for debugging
-OPTIMIZATION = -Os
-
-# Output file basename
-OUTPUT = applet-serialflash-$(CHIP)
-
-# Output directories
-BIN = bin
-OBJ = obj
-
-#-------------------------------------------------------------------------------
-#		Tools
-#-------------------------------------------------------------------------------
-
-# Tool suffix when cross-compiling
-CROSS_COMPILE = arm-none-eabi-
-
-# Libraries
-LIBRARIES = ../../libraries
-# Chip library directory
-CHIP_LIB = $(LIBRARIES)/libchip_atsam3s
-# Board library directory
-BOARD_LIB = $(LIBRARIES)/libboard_atsam3s-ek
-# Spiflash library directory
-#SPIFLASH_LIB = $(LIBRARIES)/libspiflash
-
-# ISP directory
-ISP = ..
-# tcl_lib directory
-
-#INSTALLDIR = "../../../../tcl_lib/$(BOARD_DIR)/"
-
-LIBS = -Wl,--start-group -lgcc -lc -Wl,--end-group
-
-#-lchip_$(CHIP)_gcc_rel -lboard_$(BOARD)_gcc_rel -lspiflash_gcc_rel -Wl,--end-group
-
-LIB_PATH = -L$(CHIP_LIB)/lib
-LIB_PATH += -L$(BOARD_LIB)/lib
-#LIB_PATH += -L$(SPIFLASH_LIB)/lib
-#LIB_PATH+=-L=/lib
-#LIB_PATH+=-L=/../lib/gcc/arm-none-eabi/4.4.1
-
-# Compilation tools
-AR = $(CROSS_COMPILE)ar
-CC = $(CROSS_COMPILE)gcc
-LD = $(CROSS_COMPILE)ld
-SIZE = $(CROSS_COMPILE)size
-STRIP = $(CROSS_COMPILE)strip
-OBJCOPY = $(CROSS_COMPILE)objcopy
-GDB = $(CROSS_COMPILE)gdb
-NM = $(CROSS_COMPILE)nm
-CLSS = $(CROSS_COMPILE)objdump
-
-# Flags
-INCLUDES  = -I$(CHIP_LIB)
-INCLUDES += -I$(BOARD_LIB)
-INCLUDES += -I$(SPIFLASH_LIB)
-INCLUDES += -I$(LIBRARIES)
-
-CFLAGS += -Wall -Wchar-subscripts -Wcomment -Wformat=2 -Wimplicit-int
-CFLAGS += -Werror-implicit-function-declaration -Wmain -Wparentheses
-CFLAGS += -Wsequence-point -Wreturn-type -Wswitch -Wtrigraphs -Wunused
-CFLAGS += -Wuninitialized -Wunknown-pragmas -Wfloat-equal -Wundef
-CFLAGS += -Wshadow -Wpointer-arith -Wbad-function-cast -Wwrite-strings
-CFLAGS += -Wsign-compare -Waggregate-return -Wstrict-prototypes
-CFLAGS += -Wmissing-prototypes -Wmissing-declarations
-CFLAGS += -Wformat -Wmissing-format-attribute -Wno-deprecated-declarations
-CFLAGS += -Wpacked -Wredundant-decls -Wnested-externs -Winline -Wlong-long
-CFLAGS += -Wunreachable-code
-CFLAGS += -Wcast-align
-#CFLAGS += -Wmissing-noreturn
-#CFLAGS += -Wconversion
-
-# To reduce application size use only integer printf function.
-CFLAGS += -Dprintf=iprintf
-TRACE_LEVEL = 4
-#CFLAGS += -DTRACE_LEVEL=$(TR_LEV)
- #-DDYN_TRACES
-# -mlong-calls  -Wall
-CFLAGS += -ffunction-sections  -D$(MEMORIES)
-#CFLAGS += -DNDEBUG
-CFLAGS += -mthumb -g -gdwarf-2 $(OPTIMIZATION) $(INCLUDES) -D$(CHIP) -DTRACE_LEVEL=$(TRACE_LEVEL) -DDYN_TRACES
-ASFLAGS = -Wall -g $(OPTIMIZATION) $(INCLUDES) -D$(CHIP) -D__ASSEMBLY__
-LDFLAGS= -nostartfiles -Wl,--cref -Wl,--check-sections -Wl,--gc-sections -Wl,--entry=entry -Wl,--unresolved-symbols=report-all -Wl,--warn-common -Wl,--warn-section-align -Wl,--warn-unresolved-symbols
-LD_OPTIONAL=-Wl,--print-gc-sections -Wl,--stats
-
-#-------------------------------------------------------------------------------
-#		Files
-#-------------------------------------------------------------------------------
-
-# Directories where source files can be found
-
-VPATH += ../..
-VPATH += $(ISP)/common
-
-
-# Objects built from Asm source files
-//ASM_OBJECTS = applet_cstartup.o
-
-# Objects built from C source files
-C_OBJECTS += main.o
-C_OBJECTS += applet_cstartup.o
-
-# Append OBJ and BIN directories to output filename
-OUTPUT := $(BIN)/$(OUTPUT)
-
-#-------------------------------------------------------------------------------
-#		Rules
-#-------------------------------------------------------------------------------
-
-all: $(BIN) $(OBJ) $(MEMORIES)
-
-$(BIN) $(OBJ):
-	mkdir $@
-
-define RULES
-C_OBJECTS_$(1) = $(addprefix $(OBJ)/$(1)_, $(C_OBJECTS))
-ASM_OBJECTS_$(1) = $(addprefix $(OBJ)/$(1)_, $(ASM_OBJECTS))
-
-$(1): $$(ASM_OBJECTS_$(1)) $$(C_OBJECTS_$(1))
-	$(CC) $(LIB_PATH) $(LDFLAGS) $(LD_OPTIONAL) -T"$(BOARD_LIB)/resources/gcc/$(CHIP)/$$@_samba.lds" -Wl,-Map,$(OUTPUT).map -o $(OUTPUT).elf $$^ $(LIBS) 
-	$(NM) $(OUTPUT).elf >$(OUTPUT).elf.txt 
-	$(OBJCOPY) -O binary $(OUTPUT).elf $(OUTPUT).bin 
-	$(SIZE) $$^ $(OUTPUT).elf 
-	$(CLSS) -h -S $(OUTPUT).elf >$(OUTPUT).lss
-#	@[ -e $(INSTALLDIR) ] || mkdir $(INSTALLDIR)
-#	@cp -f $(OUTPUT).bin $(INSTALLDIR)
-	
-$$(C_OBJECTS_$(1)): $(OBJ)/$(1)_%.o: %.c Makefile $(OBJ) $(BIN)
-	$(CC) $(CFLAGS) -D$(1) -c -o $$@ $$<
-
-$$(ASM_OBJECTS_$(1)): $(OBJ)/$(1)_%.o: %.S Makefile $(OBJ) $(BIN)
-	$(CC) $(ASFLAGS) -D$(1) -c -o $$@ $$<
-
-debug_$(1): $(1)
-	$(GDB) -x "$(BOARD_LIB)/resources/gcc/$(BOARD)_$(1).gdb" -ex "reset" -readnow -se $(OUTPUT)-$(1).elf
-endef
-
-$(foreach MEMORY, $(MEMORIES), $(eval $(call RULES,$(MEMORY))))
-
-clean:
-	-del $(OBJ)\*.o $(BIN)\*.bin $(BIN)\*.elf $(BIN)\*.map
-
-# Create extended listing file from ELF output file.
-%.lss: %.elf
-	@echo
-	@echo $(MSG_EXTENDED_LISTING) $@
-	$(OBJDUMP) -h -S $< > $@
-

applets/ersky9x/serialFlash/main.c

@@ -1,971 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2011, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-
-/*----------------------------------------------------------------------------
- *        Headers
- *----------------------------------------------------------------------------*/
- 
-#include "../common/applet.h"
-#include <board.h>
-//#include "libspiflash.h"
-#include <string.h>
-
-#undef DYN_TRACES
-#define DYN_TRACES 0
-
-
-
-/*----------------------------------------------------------------------------
- *        Internal definitions
- *----------------------------------------------------------------------------*/
-
-/** SPI clock frequency in Hz. */
-#define SPCK    8000000
-
-
-/** Stack size in SRAM */
-#define STACK_SIZE 0x100
-
-/** Last erased sector id, this will avoid to erase if the block is already erased. */
-//static unsigned short lastErasedBlock = 0xFFFF;
-
-/** Indicate the farthest memory offset ever erase, if current write address is less
- than the address, the related block should be erase again before write. */
-//static uint32_t writtenAddress = 0;
-
-
-/** Max size of data we can tranfsert in one shot */
-#define MAX_COUNT 0x6000
-
-/** Chip select value used to select the AT25 chip. */
-#define SPI_CS          0
-/** SPI peripheral pins to configure to access the serial flash. */
-#define SPI_PINS        PINS_SPI0, PIN_SPI0_NPCS0
-
-/*----------------------------------------------------------------------------
- *        Types
- *----------------------------------------------------------------------------*/
-/** Structure for storing parameters for each command that can be performed by
-the applet. */
-struct _Mailbox {
-
-    /** Command send to the monitor to be executed. */
-    uint32_t command;
-    /** Returned status, updated at the end of the monitor execution.*/
-    uint32_t status;
-
-    /** Input Arguments in the argument area*/
-    union {
-
-        /** Input arguments for the Init command.*/
-        struct {
-
-            /** Communication link used.*/
-            uint32_t comType;
-            /**Trace level.*/
-            uint32_t traceLevel;
-            /** Serial flash index.*/
-            uint32_t at25Idx;
-
-        } inputInit;
-
-        /** Output arguments for the Init command.*/
-        struct {
-
-            /** Memory size.*/
-            uint32_t memorySize;
-            /** Buffer address.*/
-            uint32_t bufferAddress;
-            /** Buffer size.*/
-            uint32_t bufferSize;
-
-        } outputInit;
-
-        /** Input arguments for the Write command.*/
-        struct {
-
-            /** Buffer address.*/
-            uint32_t bufferAddr;
-            /** Buffer size.*/
-            uint32_t bufferSize;
-            /** Memory offset.*/
-            uint32_t memoryOffset;
-
-        } inputWrite;
-
-        /** Output arguments for the Write command.*/
-        struct {
-
-            /** Bytes written.*/
-            uint32_t bytesWritten;
-
-            uint32_t bufferSize;		// temp
-            /** Memory offset.*/
-            uint32_t memoryOffset;	// temp
-						uint32_t debug1 ;
-						uint32_t debug2 ;
-
-        } outputWrite;
-
-        /** Input arguments for the Read command.*/
-        struct {
-
-            /** Buffer address. */
-            uint32_t bufferAddr;
-            /** Buffer size.*/
-            uint32_t bufferSize;
-            /** Memory offset.*/
-            uint32_t memoryOffset;
-
-        } inputRead;
-
-        /** Output arguments for the Read command.*/
-        struct {
-
-            /** Bytes read.*/
-            uint32_t bytesRead;
-
-        } outputRead;
-
-        /** Input arguments for the Full Erase command.*/
-        // NONE
-
-        /** Output arguments for the Full Erase command.*/
-        // NONE
-        /** Input arguments for the Buffer Erase command.*/
-        struct {
-
-            /** Memory offset to be erase.*/
-            uint32_t memoryOffset;
-
-        } inputBufferErase;
-
-        /** Output arguments for the Buffer Erase command.*/
-        struct {
-
-            /** Memory offset to be erase.*/
-            uint32_t bytesErased;
-
-        } outputBufferErase;
-    } argument;
-};
-
-/*----------------------------------------------------------------------------
- *        Global variables
- *----------------------------------------------------------------------------*/
-
-/** End of program space (code + data). */
-extern int end;
-extern int _sstack;
-/*----------------------------------------------------------------------------
- *        Local variables
- *----------------------------------------------------------------------------*/
-/** Global DMA driver instance for all DMA transfers in application. */
-//static sDmad dmad;
-
-/** SPI driver instance. */
-//static Spid spid;
-
-/** Serial flash driver instance. */
-//static At25 at25;
-
-/** Pins to configure for the application. */
-//static Pin pins[] = {SPI_PINS};
-
-/** Size of one page in the serial flash, in bytes.  */
-static uint32_t pageSize;
-
-/** Size of one block in the serial flash, in bytes.  */
-static uint32_t blockSize;
-
-/**Size of the buffer used for read/write operations in bytes. */
-static uint32_t bufferSize;
-
-/** Depending on DYN_TRACES, dwTraceLevel is a modifable runtime variable or a define */
-uint32_t dwTraceLevel;
-
-uint32_t Spi_init_done = 0 ;
-struct _Mailbox *Pmailbox = 0 ;
-
-uint8_t Spi_tx_buf[24] ;
-uint8_t Spi_rx_buf[24] ;
-
-uint8_t Block_buffer[4096] ;
-
-/*----------------------------------------------------------------------------
- *         Global functions
- *----------------------------------------------------------------------------*/
-
-
-uint32_t  eeprom_write_one( uint8_t byte, uint8_t count ) ;
-uint32_t eeprom_read_status( void ) ;
-void eeprom_write_enable( void ) ;
-void eeprom_wait_busy( void ) ;
-uint32_t spi_operation( register uint8_t *tx, register uint8_t *rx, register uint32_t count ) ;
-void init_spi( void ) ;
-uint32_t unprotect_eeprom( void ) ;
-uint32_t spi_PDC_action( register uint8_t *command, register uint8_t *tx, register uint8_t *rx, register uint32_t comlen, register uint32_t count ) ;
-uint32_t eeprom_block_erased( register uint8_t *p) ;
-uint32_t eeprom_page_erased( register uint8_t *p) ;
-void AT25D_Read( uint8_t *BufferAddr, uint32_t size, uint32_t memoryOffset) ;
-void AT25D_Write( uint8_t *BufferAddr, uint32_t size, uint32_t memoryOffset ) ;
-uint32_t AT25D_EraseBlock( uint32_t memoryOffset ) ;
-//uint32_t min( uint32_t a, uint32_t b ) ;
-
-
-uint32_t eeprom_write_one( uint8_t byte, uint8_t count )
-{
-	register Spi *spiptr ;
-	register uint32_t result ;
-	
-	spiptr = SPI ;
-	spiptr->SPI_CR = 1 ;								// Enable
-	(void) spiptr->SPI_RDR ;		// Dump any rx data
-	
-	spiptr->SPI_TDR = byte ;
-
-	result = 0 ; 
-	while( ( spiptr->SPI_SR & SPI_SR_RDRF ) == 0 )
-	{
-		// wait for received
-		if ( ++result > 10000 )
-		{
-			break ;				
-		}
-	}
-	if ( count == 0 )
-	{
-		spiptr->SPI_CR = 2 ;								// Disable
-		return spiptr->SPI_RDR ;
-	}
-	(void) spiptr->SPI_RDR ;		// Dump the rx data
-	spiptr->SPI_TDR = 0 ;
-	result = 0 ; 
-	while( ( spiptr->SPI_SR & SPI_SR_RDRF ) == 0 )
-	{
-		// wait for received
-		if ( ++result > 10000 )
-		{
-			break ;				
-		}
-	}
-	spiptr->SPI_CR = 2 ;								// Disable
-	return spiptr->SPI_RDR ;
-}
-
-
-uint32_t eeprom_read_status()
-{
-	return eeprom_write_one( 5, 1 ) ;
-}
-
-
-void eeprom_write_enable()
-{
-	eeprom_write_one( 6, 0 ) ;
-}
-
-void eeprom_wait_busy()
-{
-	register uint32_t x ;
-	register uint32_t y ;
-	
-	y = 0 ;
-	do
-	{
-		y += 1 ;
-		if ( y > 1000000 )
-		{
-			break ;			
-		}
-		x = eeprom_read_status() ;
-	} while ( x & 1 ) ;
-  
-	Pmailbox->argument.outputWrite.debug2 = y ;
-}
-
-uint32_t spi_operation( register uint8_t *tx, register uint8_t *rx, register uint32_t count )
-{
-	register Spi *spiptr ;
-	register uint32_t result ;
-
-//  PMC->PMC_PCER0 |= 0x00200000L ;		// Enable peripheral clock to SPI
-
-	result = 0 ; 
-	spiptr = SPI ;
-	spiptr->SPI_CR = 1 ;								// Enable
-	(void) spiptr->SPI_RDR ;		// Dump any rx data
-	while( count )
-	{
-		result = 0 ;
-		while( ( spiptr->SPI_SR & SPI_SR_TXEMPTY ) == 0 )
-		{
-			// wait
-			if ( ++result > 10000 )
-			{
-				result = 0xFFFF ;
-				break ;				
-			}
-		}
-		if ( result > 10000 )
-		{
-			break ;
-		}
-//		if ( count == 1 )
-//		{
-//			spiptr->SPI_CR = SPI_CR_LASTXFER ;		// LastXfer bit
-//		}
-		spiptr->SPI_TDR = *tx++ ;
-		result = 0 ;
-		while( ( spiptr->SPI_SR & SPI_SR_RDRF ) == 0 )
-		{
-			// wait for received
-			if ( ++result > 10000 )
-			{
-				result = 0x2FFFF ;
-				break ;				
-			}
-		}
-		if ( result > 10000 )
-		{
-			break ;
-		}
-		*rx++ = spiptr->SPI_RDR ;
-		count -= 1 ;
-	}
-	if ( result <= 10000 )
-	{
-		result = 0 ;
-	}
-	spiptr->SPI_CR = 2 ;								// Disable
-
-// Power save
-//  PMC->PMC_PCER0 &= ~0x00200000L ;		// Disable peripheral clock to SPI
-
-	return result ;
-}
-
-uint32_t spi_PDC_action( register uint8_t *command, register uint8_t *tx, register uint8_t *rx, register uint32_t comlen, register uint32_t count )
-{
-	register Spi *spiptr ;
-//	register uint32_t result ;
-	register uint32_t condition ;
-	static uint8_t discard_rx_command[4] ;
-
-//  PMC->PMC_PCER0 |= 0x00200000L ;		// Enable peripheral clock to SPI
-
-//	Spi_complete = 0 ;
-	if ( comlen > 4 )
-	{
-//		Spi_complete = 1 ;
-		return 0x4FFFF ;		
-	}
-	condition = SPI_SR_TXEMPTY ;
-	spiptr = SPI ;
-	spiptr->SPI_CR = 1 ;				// Enable
-	(void) spiptr->SPI_RDR ;		// Dump any rx data
-	(void) spiptr->SPI_SR ;			// Clear error flags
-	spiptr->SPI_RPR = (uint32_t)discard_rx_command ;
-	spiptr->SPI_RCR = comlen ;
-	if ( rx )
-	{
-		spiptr->SPI_RNPR = (uint32_t)rx ;
-		spiptr->SPI_RNCR = count ;
-		condition = SPI_SR_RXBUFF ;
-	}
-	spiptr->SPI_TPR = (uint32_t)command ;
-	spiptr->SPI_TCR = comlen ;
-	if ( tx )
-	{
-		spiptr->SPI_TNPR = (uint32_t)tx ;
-	}
-	else
-	{
-		spiptr->SPI_TNPR = (uint32_t)rx ;
-	}
-	spiptr->SPI_TNCR = count ;
-
-	spiptr->SPI_PTCR = SPI_PTCR_RXTEN | SPI_PTCR_TXTEN ;	// Start transfers
-
-	// Wait for things to get started, avoids early interrupt
-	for ( count = 0 ; count < 1000 ; count += 1 )
-	{
-		if ( ( spiptr->SPI_SR & SPI_SR_TXEMPTY ) == 0 )
-		{
-			break ;			
-		}
-	}
-	
-	count = 0 ;
-	while( ( spiptr->SPI_SR & condition ) == 0 )
-	{
-		if ( ++count > 1000000 )
-		{
-			break ;			
-		}
-	}
-	
-	spiptr->SPI_CR = 2 ;				// Disable
-	(void) spiptr->SPI_RDR ;		// Dump any rx data
-	(void) spiptr->SPI_SR ;			// Clear error flags
-	spiptr->SPI_PTCR = SPI_PTCR_RXTDIS | SPI_PTCR_TXTDIS ;	// Stop tramsfers
-
-	if ( count > 1000000 )
-	{
-		return 1 ;
-	}
-	return 0 ;
-}
-
-
-uint32_t unprotect_eeprom()
-{
- 	register uint8_t *p ;
-
-	eeprom_write_enable() ;
-		
-	p = Spi_tx_buf ;
-	*p = 0x39 ;		// Unprotect sector command
-	*(p+1) = 0 ;
-	*(p+2) = 0 ;
-	*(p+3) = 0 ;		// 3 bytes address
-
-	return spi_operation( p, Spi_rx_buf, 4 ) ;
-}
-
-
-
-
-
-
-void init_spi()
-{
-	register Pio *pioptr ;
-	register Spi *spiptr ;
-	register uint32_t timer ;
-	register uint8_t *p ;
-	uint8_t spi_buf[4] ;
-
-	if ( !Spi_init_done)
-	{
-  	PMC->PMC_PCER0 |= 0x00200000L ;		// Enable peripheral clock to SPI
-  	/* Configure PIO */
-		pioptr = PIOA ;
-  	pioptr->PIO_ABCDSR[0] &= ~0x00007800 ;	// Peripheral A bits 14,13,12,11
-  	pioptr->PIO_ABCDSR[1] &= ~0x00007800 ;	// Peripheral A
-  	pioptr->PIO_PDR = 0x00007800 ;					// Assign to peripheral
-	
-		spiptr = SPI ;
-		timer = ( 64000000 / 3000000 ) << 8 ;
-		spiptr->SPI_MR = 0x14000011 ;				// 0001 0100 0000 0000 0000 0000 0001 0001 Master
-		spiptr->SPI_CSR[0] = 0x01180009 | timer ;		// 0000 0001 0001 1000 xxxx xxxx 0000 1001
-	//	NVIC_EnableIRQ(SPI_IRQn) ;
-
-		p = spi_buf ;
-		
-	//	*p = 0x39 ;		// Unprotect sector command
-	//	*(p+1) = 0 ;
-	//	*(p+2) = 0 ;
-	//	*(p+3) = 0 ;		// 3 bytes address
-
-	//	spi_operation( p, spi_buf, 4 ) ;
-	
-		eeprom_write_enable() ;
-
-		*p = 1 ;		// Write status register command
-		*(p+1) = 0 ;
-		spi_operation( p, spi_buf, 2 ) ;
-		Spi_init_done = 1 ;
-	}
-
-}
-
-uint32_t eeprom_block_erased( register uint8_t *p)
-{
-	register uint32_t x ;
-	register uint32_t result ;
-
-	result = 1 ;
-
-	for ( x = 0 ; x < 4096 ; x += 1 )
-	{
-		if ( *p++ != 0xFF )
-		{
-			result = 0 ;			
-			break ;
-		}		
-	}
-	return result ;
-}
-
-uint32_t eeprom_page_erased( register uint8_t *p)
-{
-	register uint32_t x ;
-	register uint32_t result ;
-
-	result = 1 ;
-
-	for ( x = 0 ; x < 256 ; x += 1 )
-	{
-		if ( *p++ != 0xFF )
-		{
-			result = 0 ;			
-			break ;
-		}		
-	}
-	return result ;
-}
-
-
-void AT25D_Read( uint8_t *BufferAddr, uint32_t size, uint32_t memoryOffset)
-{
-	register uint8_t *p ;
-	
-	p = Spi_tx_buf ;
-	*p = 3 ;		// Read command
-	*(p+1) = memoryOffset >> 16 ;
-	*(p+2) = memoryOffset >> 8 ;
-	*(p+3) = memoryOffset ;		// 3 bytes address
-	
-	spi_PDC_action( p, 0, BufferAddr, 4, size ) ;
-}
-
-void AT25D_Write( uint8_t *BufferAddr, uint32_t size, uint32_t memoryOffset )
-{
-	register uint8_t *p ;
-	
-	eeprom_write_enable() ;
-	
-	p = Spi_tx_buf ;
-	*p = 2 ;		// Write command
-	*(p+1) = memoryOffset >> 16 ;
-	*(p+2) = memoryOffset >> 8 ;
-	*(p+3) = memoryOffset ;		// 3 bytes address
-		 
-	spi_PDC_action( p, BufferAddr, 0, 4, size ) ;
-
-	eeprom_wait_busy() ;
-
-}
-
-uint32_t AT25D_EraseBlock( uint32_t memoryOffset )
-{
-	register uint8_t *p ;
-	register uint32_t x ;
-	
-	eeprom_write_enable() ;
-	p = Spi_tx_buf ;
-	*p = 0x20 ;		// Block Erase command
-	*(p+1) = memoryOffset >> 16 ;
-	*(p+2) = memoryOffset >> 8 ;
-	*(p+3) = memoryOffset ;		// 3 bytes address
-	x = spi_operation( p, Spi_rx_buf, 4 ) ;
-
-	eeprom_wait_busy() ;
-	return x ;
-}
-
-//uint32_t min( uint32_t a, uint32_t b )
-//{
-//	if ( a < b )
-//	{
-//		return a ;
-//	}
-//	return b ;
-//}
-
-/**
- * \brief Applet main entry. This function decodes received command and executes it.
- * \param argc  always 1
- * \param argv  Address of the argument area.
-*/
-
-int main(int argc, char **argv)
-{
-    struct _Mailbox *pMailbox = (struct _Mailbox *) argv;
-    Pmailbox = pMailbox ;
-    /* Communication type with SAM-BA GUI. */
-//    uint8_t comType;
-
-//    uint32_t jedecId;
-    uint32_t bytesToWrite, bytesToRead, bufferAddr, startMemoryOffset, memoryOffset, packetSize;
-    /* index on read/write buffer */
-    uint8_t *pBuffer;
-    /* Temporary buffer used for non block aligned read/write */
-//    uint32_t tempBufferAddr;
-    /* Offset in destination buffer during buffer copy */
-//    uint32_t bufferOffset;
-    
-    uint32_t block_address ;
-    uint32_t x ;
-    /* INIT */  
-    /* Save communication link type */
-//    comType = pMailbox->argument.inputInit.comType;
-		
-    init_spi() ;
-
-    if (pMailbox->command == APPLET_CMD_INIT)
-    {
-#if (DYN_TRACES == 1)
-        dwTraceLevel = pMailbox->argument.inputInit.traceLevel;
-#endif
-
-//        TRACE_INFO("-- SerialFlash AT25/AT26 applet %s --\n\r", SAM_BA_APPLETS_VERSION);
-//        TRACE_INFO("-- %s\n\r", BOARD_NAME);
-//        TRACE_INFO("-- Compiled: %s %s --\n\r", __DATE__, __TIME__);
-        /* Configure pins */
-//        PIO_Configure(pins, PIO_LISTSIZE(pins));
-        /* Initialize DMA driver instance with polling mode */
-//        DMAD_Initialize( &dmad, 1 );
-        
-        /* Initialize the SPI and serial flash */
-				init_spi() ;
-
-
-
-//        SPID_Configure(&spid, SPI0, ID_SPI0, &dmad);
-//        AT25_Configure(&at25, &spid, SPI_CS, 1);
-//        TRACE_INFO("SPI and AT25/AT25 drivers initialized\n\r");
-        pMailbox->argument.outputInit.bufferAddress = (uint32_t) &end ;
-        /* Read the JEDEC ID of the device to identify it */
-//        jedecId = AT25D_ReadJedecId(&at25);
-//        if (AT25_FindDevice(&at25, jedecId) == 0) {
-//            pMailbox->status = APPLET_DEV_UNKNOWN;
-//            pMailbox->argument.outputInit.bufferSize = 0;
-//            pMailbox->argument.outputInit.memorySize = 0;
-//            TRACE_INFO("Device Unknown\n\r");
-//            goto exit;
-//        }
-//        else {
-            /* Get device parameters */
-            pMailbox->status = APPLET_SUCCESS;
-            pageSize = 256 ;
-//            pageSize = AT25_PageSize(&at25);
-            blockSize = 4096 ;
-//            blockSize = AT25_BlockSize(&at25);
-
-            /* Program page */
-//            if (AT25_ManId(&at25) == SST_SPI_FLASH) {
-                /* SST Flash write is slower, we reduce buffer size to avoid USB timeout */
-//                bufferSize = 10 * pageSize;
-//            }
-//            else {
-                bufferSize = 2 * blockSize;
-//            }
-            /* integer number of pages can be contained in each buffer */
-            bufferSize -= bufferSize % pageSize; 
-            if ( bufferSize < pageSize) {
-  //              TRACE_INFO("No enought memory to load buffer.\n\r");
-                goto exit;
-            } 
-            pMailbox->argument.outputInit.bufferSize = bufferSize;
-            pMailbox->argument.outputInit.memorySize = 128*4096;
-//            TRACE_INFO("%s blockSize : 0x%lx bufferAddr : 0x%lx\n\r",
-//                   "sky9x", blockSize, pMailbox->argument.outputInit.bufferAddress);
-//        }
-    }
-
-    // ----------------------------------------------------------
-    // WRITE:
-    // ----------------------------------------------------------
-    else if (pMailbox->command == APPLET_CMD_WRITE)
-		{
-        startMemoryOffset = pMailbox->argument.inputWrite.memoryOffset;
-        memoryOffset      = startMemoryOffset;
-        bufferAddr        = pMailbox->argument.inputWrite.bufferAddr;
-//        tempBufferAddr    = bufferAddr + bufferSize;
-        bytesToWrite      = pMailbox->argument.inputWrite.bufferSize;
-//        TRACE_INFO("WRITE at offset: 0x%lx buffer at : 0x%lx of: 0x%lx Bytes\n\r",
-//               memoryOffset, bufferAddr, bytesToWrite);
-        /* Check word alignment */
-        if (memoryOffset % 4) {
-
-            pMailbox->status = APPLET_ALIGN_ERROR;
-            goto exit;
-        }
-
-				unprotect_eeprom() ;
-//        if (AT25D_Unprotect(&at25)) {
-
-//            TRACE_INFO("Can not unprotect the flash\n\r");
-//            pMailbox->status = APPLET_UNPROTECT_FAIL;
-//            goto exit;
-//        }
-
-        pBuffer = (uint8_t *) bufferAddr;
-
-				block_address = memoryOffset &0xFFFFF000 ;		// 4k boundary
-        AT25D_Read( Block_buffer, 4096, block_address ) ;	// read block to write to
-				// Check to see if it is blank
-				x = eeprom_block_erased( Block_buffer ) ;
-				if ( x == 0 )
-				{
-					AT25D_EraseBlock( block_address ) ;
-				}
-
-				if (bytesToWrite)
-				{
-					uint32_t bytes_to_copy ;
-					uint32_t i ;
-					uint32_t j ;
-					uint8_t *s ;
-					uint8_t *dest ;
-
-					dest = Block_buffer + (memoryOffset & 0x0FFF ) ;
-					s = pBuffer ;
-					bytes_to_copy = 4096 - ( memoryOffset - block_address ) ;
-					if ( bytes_to_copy > bytesToWrite )
-					{
-						bytes_to_copy = bytesToWrite ;
-					}
-					for ( i = 0 ; i < bytes_to_copy ; i += 1 )
-					{
-						*dest++ = *s++ ;						
-					}
-					memoryOffset += bytes_to_copy ;
-					bytesToWrite -= bytes_to_copy ;
-					s = Block_buffer ;
-					j = 0 ;
-					for ( i = 0 ; i < 16 ; i += 1 )		// pages in block
-					{
-						j <<= 1 ;
-						x = eeprom_page_erased( s ) ;
-						if ( x == 0 )				// Not blank
-						{
-            	AT25D_Write( s, 256, block_address ) ;
-							j |= 1 ;
-						}						
-						s += 256 ;
-						block_address += 256 ;
-					}
-		  pMailbox->argument.outputWrite.debug1 = j ;
-				}
-
-
-//        if ((memoryOffset % pageSize) != 0) {
-
-//            /*  We are not page aligned, retrieve first page content to update it*/
-//            if (memoryOffset < writtenAddress) {
-//                lastErasedBlock = 0xFFFF;
-//            }
-//            /*  Flush temp buffer */
-//            memset((uint32_t *)tempBufferAddr, 0xFF, pageSize);
-
-//            bufferOffset = (memoryOffset % pageSize);
-//            packetSize = pageSize - bufferOffset;
-//            memoryOffset -= bufferOffset;
-//            /*  Read page to be updated*/
-//            AT25D_Read( (uint8_t *) tempBufferAddr, pageSize, memoryOffset);
-//            /* Fill retrieved page with data to be programmed */
-//            memcpy((uint8_t *)(tempBufferAddr + bufferOffset), pBuffer, packetSize);
-
-//             if (((memoryOffset / blockSize) > lastErasedBlock) || (lastErasedBlock == 0xFFFF)) {
-//                /* Erase the block to be updated */
-////                AT25D_EraseBlock( memoryOffset);
-//                lastErasedBlock = (memoryOffset / blockSize);
-//            }
-
-//            /*  Write the page contents */
-////            AT25D_Write( (uint8_t *) tempBufferAddr, pageSize, memoryOffset);
-//            bytesToWrite = (bytesToWrite > packetSize) ? (bytesToWrite - packetSize) : 0;
-//            pBuffer += packetSize;
-//            memoryOffset += pageSize;
-//            writtenAddress = memoryOffset;
-//        }
-
-//        /*  If it remains more than one page to write */
-//        while (bytesToWrite >= pageSize)
-//				{
-//            if (memoryOffset < writtenAddress)
-//						{
-//                lastErasedBlock = 0xFFFF;
-//            }
-//             if (((memoryOffset / blockSize) > lastErasedBlock) || (lastErasedBlock == 0xFFFF)) {
-//                 /* Erase the block to be updated */
-////                AT25D_EraseBlock( memoryOffset);
-//                 lastErasedBlock = (memoryOffset / blockSize);
-//            }
-//            /*  Write the page contents */
-//            AT25D_Write( (uint8_t *) pBuffer, pageSize, memoryOffset);
-//            pBuffer += pageSize;
-//            memoryOffset += pageSize;
-//            bytesToWrite -= pageSize;
-//            writtenAddress = memoryOffset;
-//        }
-
-//        /*  Write remaining data */
-//        if (bytesToWrite > 0) {
-
-//            /*  Read previous content of page */
-//            AT25D_Read( (uint8_t *) tempBufferAddr, pageSize, memoryOffset);
-//            /*  Fill retrieved block with data to be programmed */
-//            memcpy((uint8_t *)tempBufferAddr, pBuffer, bytesToWrite);
-//            if (((memoryOffset / blockSize) > lastErasedBlock) || (lastErasedBlock == 0xFFFF)) {
-//                 /*  Erase the block to be updated */
-////                AT25D_EraseBlock( memoryOffset);
-//                 lastErasedBlock = (memoryOffset / blockSize);
-//            }
-//            /*  Write the page contents */;
-////            AT25D_Write( (uint8_t *) tempBufferAddr, pageSize, memoryOffset);
-//            writtenAddress = memoryOffset + bytesToWrite;
-//            /*  No more bytes to write */
-//            bytesToWrite = 0;
-//        }
-
-////        TRACE_INFO("WRITE return byte written : 0x%lx Bytes\n\r",
-////               pMailbox->argument.inputWrite.bufferSize - bytesToWrite);
-
-        pMailbox->argument.outputWrite.bytesWritten = pMailbox->argument.inputWrite.bufferSize - bytesToWrite;
-//        pMailbox->argument.outputWrite.bytesWritten = bytesToWrite;
-        pMailbox->status = APPLET_SUCCESS;
-    }
-
-//    // ----------------------------------------------------------
-//    // READ:
-//    // ----------------------------------------------------------
-    else if (pMailbox->command == APPLET_CMD_READ)
-		{
-        memoryOffset = pMailbox->argument.inputRead.memoryOffset;
-        bufferAddr   = pMailbox->argument.inputRead.bufferAddr;
-        bytesToRead  = pMailbox->argument.inputRead.bufferSize;
-
-//        TRACE_INFO("READ at offset: 0x%lx buffer at : 0x%lx of: 0x%lx Bytes\n\r",
-//               memoryOffset, bufferAddr, bytesToRead);
-        /*  Check word alignment */
-        if (memoryOffset % 4) {
-
-            pMailbox->status = APPLET_ALIGN_ERROR;
-            goto exit;
-        }
-        pBuffer = (uint8_t *) bufferAddr;
-
-        /* Read packet after packets */
-        while (((uint32_t)pBuffer < (bufferAddr + bufferSize)) && (bytesToRead > 0))
-				{
-				    packetSize = bytesToRead ;
-						if ( packetSize > MAX_COUNT )
-						{
-							packetSize = MAX_COUNT ;					
-						}
-            AT25D_Read( pBuffer, packetSize, memoryOffset);
-            pBuffer += packetSize;
-            bytesToRead -= packetSize;
-            memoryOffset += packetSize;
-        }
-
-//        TRACE_INFO("READ return byte read : 0x%lx Bytes\n\r",
-//               pMailbox->argument.inputRead.bufferSize - bytesToRead);
-
-        pMailbox->argument.outputRead.bytesRead = pMailbox->argument.inputRead.bufferSize - bytesToRead;
-        pMailbox->status = APPLET_SUCCESS;
-    }
-
-//    // ----------------------------------------------------------
-//    // FULL ERASE:
-//    // ----------------------------------------------------------
-    else if (pMailbox->command == APPLET_CMD_FULL_ERASE)
-		{
-            pMailbox->status = APPLET_ERASE_FAIL;
-//        TRACE_INFO("FULL ERASE\n\r");
-
-//				unprotect_eeprom() ;
-
-//        /* Unprotected the flash */
-////        if (AT25D_Unprotect(&at25)) {
-
-////            TRACE_INFO("Can not unprotect the flash\n\r");
-////            pMailbox->status = APPLET_UNPROTECT_FAIL;
-////            goto exit;
-////        }
-
-//        TRACE_INFO("Flash unprotected\n\r");
-
-//        /* Erase the chip */
-//        TRACE_INFO("Chip is being erased...\n\r");
-
-////        if (AT25D_EraseChip()) {
-
-//				// NOT IMPLEMENTED (YET?)
-
-//            TRACE_INFO("Erasing error\n\r");
-//            pMailbox->status = APPLET_ERASE_FAIL;
-//            goto exit;
-////        }
-
-//        TRACE_INFO("Full Erase achieved\n\r");
-//        pMailbox->status = APPLET_SUCCESS;
-    }
-//    // ----------------------------------------------------------
-//    // BUFFER ERASE:
-//    // ----------------------------------------------------------
-    else if (pMailbox->command == APPLET_CMD_BUFFER_ERASE)
-		{
-
-//        TRACE_INFO("BUFFER ERASE \n\r");
-         /*  Unprotected the flash */
-				unprotect_eeprom() ;
-        
-//				if (AT25D_Unprotect(&at25)) {
-
-//            TRACE_INFO("Can not unprotect the flash\n\r");
-//            pMailbox->status = APPLET_UNPROTECT_FAIL;
-//            goto exit;
-//        }
-
-         memoryOffset = pMailbox->argument.inputBufferErase.memoryOffset;
-
-       if (AT25D_EraseBlock( memoryOffset))
-			 {
-            pMailbox->status = APPLET_ERASE_FAIL;
-//            TRACE_INFO("Block erasing error\n\r");
-            goto exit;
-       }
-        pMailbox->argument.outputBufferErase.bytesErased = 4096;
-
-//        TRACE_INFO("Buffer Erase achieved\n\r");
-        pMailbox->status = APPLET_SUCCESS;
-    }
-exit:
-    /* Acknowledge the end of command */
-//    TRACE_INFO("\tEnd of applet (command : %lx --- status : %lx)\n\r", pMailbox->command, pMailbox->status);
-
-    /*  Notify the host application of the end of the command processing */
-    pMailbox->command = ~(pMailbox->command);
-    /* Send ACK character */
-//    if (comType == DBGU_COM_TYPE)
-//		{
-         /* Wait for the transmitter to be ready */
-//        while ( (DBGU->DBGU_SR & DBGU_SR_TXEMPTY) == 0 ) ;
-        /* Send character */
-//         DBGU->DBGU_THR= 0x06 ;
-//    }
-    return 0;
-}
-

applets/libraries/libboard_atsam3s-ek/board.h

@@ -1,734 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2011, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-/**
- * \page sam3s_ek_board_desc SAM3S-EK - Board Description
- *
- * \section Purpose
- *
- * A file is dedicated to descibe the AT91SAM3S-EK board.
- *
- * \section Contents
- *
- *  - For AT91SAM3S-EK information, see \subpage sam3s_ek_board_info.
- *  - For operating frequency information, see \subpage sam3s_ek_opfreq.
- *  - For using portable PIO definitions, see \subpage sam3s_ek_piodef.
- *  - For on-board memories, see \subpage sam3s_ek_mem.
- *  - Several USB definitions are included here, see \subpage sam3s_ek_usb.
- *  - For External components, see \subpage sam3s_ek_extcomp.
- *  - For Individual chip definition, see \subpage sam3s_ek_chipdef.
- *
- * To get more software details and the full list of parameters related to the
- * SAM3S-EK board configuration, please have a look at the source file:
- * \ref board.h\n
- *
- * \section Usage
- *
- *  - The code for booting the board is provided by board_cstartup_xxx.c and
- *    board_lowlevel.c.
- *  - For using board PIOs, board characteristics (clock, etc.) and external
- *    components, see board.h.
- *  - For manipulating memories, see board_memories.h.
- *
- * This file can be used as a template and modified to fit a custom board, with
- * specific PIOs usage or memory connections.
- */
-
-/**
- *  \file board.h
- *
- *  Definition of AT91SAM3S-EK characteristics, AT91SAM3S-dependant PIOs and
- *  external components interfacing.
- */
-
-#ifndef _BOARD_
-#define _BOARD_
-
-/*----------------------------------------------------------------------------
- *        Headers
- *----------------------------------------------------------------------------*/
-
-#include <chip.h>
-
-
-//#include <include/at45d.h>
-//#include <include/at45_spi.h>
-#include <include/board_lowlevel.h>
-//#include <include/board_memories.h>
-//#include <include/hamming.h>
-//#include <include/math.h>
-//#include <include/uart_console.h>
-
-/*----------------------------------------------------------------------------
- *        Definitions
- *----------------------------------------------------------------------------*/
-
-/*----------------------------------------------------------------------------*/
-/**
- * \page sam3s_ek_board_info "SAM3S-EK - Board informations"
- * This page lists several definition related to the board description.
- *
- * \section Definitions
- * - \ref BOARD_NAME
- */
-
-/** Name of the board */
-#define BOARD_NAME "ATSAM3S-EK"
-/** Board definition */
-#define atsam3sek
-/** Family definition (already defined) */
-#define atsam3s
-/** Core definition */
-#define cortexm3
-
-/*
-#define BOARD_REV_A
-*/
-#define BOARD_REV_B
-
-/*----------------------------------------------------------------------------*/
-/**
- *  \page sam3s_ek_opfreq "SAM3S-EK - Operating frequencies"
- *  This page lists several definition related to the board operating frequency
- *  (when using the initialization done by board_lowlevel.c).
- *
- *  \section Definitions
- *  - \ref BOARD_MAINOSC
- *  - \ref BOARD_MCK
- */
-
-/** Frequency of the board main oscillator */
-#define BOARD_MAINOSC           12000000
-
-/** Master clock frequency (when using board_lowlevel.c) */
-// #define BOARD_MCK               64000000
-
-/*----------------------------------------------------------------------------*/
-/**
- * \page sam3s_ek_piodef "SAM3S-EK - PIO definitions"
- * This pages lists all the pio definitions contained in board.h. The constants
- * are named using the following convention: PIN_* for a constant which defines
- * a single Pin instance (but may include several PIOs sharing the same
- * controller), and PINS_* for a list of Pin instances.
- *
- * ADC
- * - \ref PIN_ADC0_AD0
- * - \ref PIN_ADC0_AD1
- * - \ref PIN_ADC0_AD2
- * - \ref PIN_ADC0_AD3
- * - \ref PIN_ADC0_AD4
- * - \ref PIN_ADC0_AD5
- * - \ref PIN_ADC0_AD6
- * - \ref PIN_ADC0_AD7
- * - \ref PINS_ADC
- *
- * UART
- * - \ref PINS_UART
- *
- * EBI
- * - \ref PIN_EBI_DATA_BUS
- * - \ref PIN_EBI_NRD
- * - \ref PIN_EBI_NWE
- * - \ref PIN_EBI_NCS0
- * - \ref PIN_EBI_PSRAM_ADDR_BUS
- * - \ref PIN_EBI_PSRAM_NBS
- * - \ref PIN_EBI_A1
- * - \ref PIN_EBI_NCS1
- * - \ref PIN_EBI_LCD_RS
- *
- * LEDs
- * - \ref PIN_LED_0
- * - \ref PIN_LED_1
- * - \ref PIN_LED_2
- * - \ref PINS_LEDS
- *
- * MCI
- * - \ref PINS_MCI
- *
- * Push buttons
- * - \ref PIN_PUSHBUTTON_1
- * - \ref PIN_PUSHBUTTON_2
- * - \ref PINS_PUSHBUTTONS
- * - \ref PUSHBUTTON_BP1
- * - \ref PUSHBUTTON_BP2
- *
- * PWMC
- * - \ref PIN_PWMC_PWMH0
- * - \ref PIN_PWMC_PWML0
- * - \ref PIN_PWMC_PWMH1
- * - \ref PIN_PWMC_PWML1
- * - \ref PIN_PWMC_PWMH2
- * - \ref PIN_PWMC_PWML2
- * - \ref PIN_PWMC_PWMH3
- * - \ref PIN_PWMC_PWML3
- * - \ref PIN_PWM_LED0
- * - \ref PIN_PWM_LED1
- * - \ref PIN_PWM_LED2
- * - \ref CHANNEL_PWM_LED0
- * - \ref CHANNEL_PWM_LED1
- * - \ref CHANNEL_PWM_LED2
- *
- * SPI
- * - \ref PIN_SPI_MISO
- * - \ref PIN_SPI_MOSI
- * - \ref PIN_SPI_SPCK
- * - \ref PINS_SPI
- * - \ref PIN_SPI_NPCS0_PA11
- *
- * SSC
- * - \ref PIN_SSC_TD
- * - \ref PIN_SSC_TK
- * - \ref PIN_SSC_TF
- * - \ref PINS_SSC_CODEC
- *
- * PCK0
- * - \ref PIN_PCK0
- *
- * PIO PARALLEL CAPTURE
- * - \ref PIN_PIODCEN1
- * - \ref PIN_PIODCEN2
- *
- * TWI
- * - \ref TWI_V3XX
- * - \ref PIN_TWI_TWD0
- * - \ref PIN_TWI_TWCK0
- * - \ref PINS_TWI0
- * - \ref PIN_TWI_TWD1
- * - \ref PIN_TWI_TWCK1
- * - \ref PINS_TWI1
- *
- * USART0
- * - \ref PIN_USART0_RXD
- * - \ref PIN_USART0_TXD
- * - \ref PIN_USART0_CTS
- * - \ref PIN_USART0_RTS
- * - \ref PIN_USART0_SCK
- *
- * USB
- * - \ref PIN_USB_VBUS
- *
- * NandFlash
- * - \ref PIN_EBI_NANDOE
- * - \ref PIN_EBI_NANDWE
- * - \ref PIN_EBI_NANDCLE
- * - \ref PIN_EBI_NANDALE
- * - \ref PIN_EBI_NANDIO
- * - \ref BOARD_NF_CE_PIN
- * - \ref BOARD_NF_RB_PIN
- * - \ref PINS_NANDFLASH
- *
- * QTouch
- * PIO definitions for Slider
- * \ref SLIDER_IOMASK_SNS
- * \ref SLIDER_IOMASK_SNSK
- * \ref PINS_SLIDER_SNS
- * \ref PINS_SLIDER_SNSK
- *
- * PIO definitions for keys
- * \ref KEY_IOMASK_SNS
- * \ref KEY_IOMASK_SNSK
- * \ref PINS_KEY_SNS
- * \ref PINS_KEY_SNSK
- *
- * PIOS for QTouch
- * \ref PINS_QTOUCH
- */
-
-/** ADC_AD0 pin definition. */
-#define PIN_ADC0_AD0 {1 << 21, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
-/** ADC_AD1 pin definition. */
-#define PIN_ADC0_AD1 {1 << 30, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
-/** ADC_AD2 pin definition. */
-#define PIN_ADC0_AD2 {1 << 3, PIOB, ID_PIOB, PIO_INPUT, PIO_DEFAULT}
-/** ADC_AD3 pin definition. */
-#define PIN_ADC0_AD3 {1 << 4, PIOB, ID_PIOB, PIO_INPUT, PIO_DEFAULT}
-/** ADC_AD4 pin definition. */
-#define PIN_ADC0_AD4 {1 << 15, PIOC, ID_PIOC, PIO_INPUT, PIO_DEFAULT}
-/** ADC_AD5 pin definition. */
-#define PIN_ADC0_AD5 {1 << 16, PIOC, ID_PIOC, PIO_INPUT, PIO_DEFAULT}
-/** ADC_AD6 pin definition. */
-#define PIN_ADC0_AD6 {1 << 17, PIOC, ID_PIOC, PIO_INPUT, PIO_DEFAULT}
-/** ADC_AD7 pin definition. */
-#define PIN_ADC0_AD7 {1 << 18, PIOC, ID_PIOC, PIO_INPUT, PIO_DEFAULT}
-
-/** Pins ADC */
-#define PINS_ADC PIN_ADC0_AD0, PIN_ADC0_AD1, PIN_ADC0_AD2, PIN_ADC0_AD3, PIN_ADC0_AD4, PIN_ADC0_AD5, PIN_ADC0_AD6, PIN_ADC0_AD7
-
-/** Startup time max, return from Idle mode (in µs) */
-#define ADC_STARTUP_TIME_MAX       15
-/** Track and hold Acquisition Time min (in ns) */
-#define ADC_TRACK_HOLD_TIME_MIN  1200
-/** ADC clock frequence */
-#define BOARD_ADC_FREQ     (6000000)
-
-/** UART pins (UTXD0 and URXD0) definitions, PA9,10. */
-#define PINS_UART  {0x00000600, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-
-/** EBI Data Bus pins */
-#define PIN_EBI_DATA_BUS            {0xFF,    PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
-/** EBI NRD pin */
-#define PIN_EBI_NRD                 {1 << 11, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
-/** EBI NWE pin */
-#define PIN_EBI_NWE                 {1 << 8,  PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
-/** EBI NCS0 pin */
-#define PIN_EBI_NCS0                {1 << 20, PIOB, ID_PIOB, PIO_PERIPH_A, PIO_PULLUP}
-/** EBI pins for PSRAM address bus */
-#define PIN_EBI_PSRAM_ADDR_BUS      {0x3f00fff, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
-/** EBI pins for PSRAM NBS pins */
-#define PIN_EBI_PSRAM_NBS           {1 << 7, PIOB, ID_PIOB, PIO_PERIPH_B, PIO_PULLUP}, \
-                                    {1 << 15, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
-/** EBI A1 pin */
-#define PIN_EBI_A1                  {1 << 19, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
-/** EBI NCS1 pin */
-#define PIN_EBI_NCS1                {1 << 15, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP} /* LCD CS pin */
-/** EBI pin for LCD RS */
-#define PIN_EBI_LCD_RS              {1 << 19, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP} /* LCD RS pin */
-
-#define LED_BLUE      0
-#define LED_GREEN     1
-#define LED_RED       2
-
-#ifdef BOARD_REV_A
-/** LED #0 pin definition (BLUE). */
-#define PIN_LED_0   {PIO_PC20, PIOC, ID_PIOC, PIO_OUTPUT_1, PIO_DEFAULT}
-/** LED #1 pin definition (GREEN). */
-#define PIN_LED_1   {PIO_PC21, PIOC, ID_PIOC, PIO_OUTPUT_1, PIO_DEFAULT}
-/** LED #2 pin definition (RED). */
-#define PIN_LED_2   {PIO_PC22, PIOC, ID_PIOC, PIO_OUTPUT_1, PIO_DEFAULT}
-#endif
-
-#ifdef BOARD_REV_B
-/** LED #0 pin definition (BLUE). */
-#define PIN_LED_0   {PIO_PA19, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
-/** LED #1 pin definition (GREEN). */
-#define PIN_LED_1   {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
-/** LED #2 pin definition (RED). */
-#define PIN_LED_2   {PIO_PC20, PIOC, ID_PIOC, PIO_OUTPUT_1, PIO_DEFAULT}
-
-#endif
-
-/** List of all LEDs definitions. */
-#define PINS_LEDS   PIN_LED_0, PIN_LED_1, PIN_LED_2
-
-/** MCI pins definition. */
-#define PINS_MCI   {0x3fUL << 26, PIOA, ID_PIOA, PIO_PERIPH_C, PIO_PULLUP}
-/** MCI pin Card Detect. */
-#ifdef BOARD_REV_A
-#define PIN_MCI_CD {PIO_PA15, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP}
-#endif
-
-#ifdef BOARD_REV_B
-#define PIN_MCI_CD {PIO_PA6, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP}
-#endif
-
-/** Push button #0 definition. Attributes = pull-up + debounce + interrupt on rising edge. */
-#define PIN_PUSHBUTTON_1    {PIO_PB3, PIOB, ID_PIOB, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_IT_RISE_EDGE}
-/** Push button #1 definition. Attributes = pull-up + debounce + interrupt on falling edge. */
-#define PIN_PUSHBUTTON_2    {PIO_PC12, PIOC, ID_PIOC, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_IT_FALL_EDGE}
-/** List of all push button definitions. */
-#define PINS_PUSHBUTTONS    PIN_PUSHBUTTON_1, PIN_PUSHBUTTON_2
-
-/** Push button #1 index. */
-#define PUSHBUTTON_BP1   0
-/** Push button #2 index. */
-#define PUSHBUTTON_BP2   1
-
-/** Simulated joystick LEFT index. */
-#define JOYSTICK_LEFT       0
-/** Simulated joystick RIGHT index. */
-#define JOYSTICK_RIGHT      1
-
-/** PWMC PWM0 pin definition: Output High. */
-#define PIN_PWMC_PWMH0  {PIO_PC18B_PWMH0, PIOC, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT}
-/** PWMC PWM0 pin definition: Output Low. */
-#define PIN_PWMC_PWML0  {PIO_PA19B_PWML0, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
-/** PWMC PWM1 pin definition: Output High. */
-#define PIN_PWMC_PWMH1  {PIO_PC19B_PWMH1, PIOC, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT}
-/** PWMC PWM1 pin definition: Output Low. */
-#define PIN_PWMC_PWML1  {PIO_PA20B_PWML1, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
-/** PWMC PWM2 pin definition: Output High. */
-#define PIN_PWMC_PWMH2  {PIO_PC20B_PWMH2, PIOC, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT}
-/** PWMC PWM2 pin definition: Output Low. */
-#define PIN_PWMC_PWML2  {PIO_PA16C_PWML2, PIOA, ID_PIOA, PIO_PERIPH_C, PIO_DEFAULT}
-/** PWMC PWM3 pin definition: Output High. */
-#define PIN_PWMC_PWMH3  {PIO_PC21B_PWMH3, PIOC, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT}
-/** PWMC PWM3 pin definition: Output Low. */
-#define PIN_PWMC_PWML3  {PIO_PA15C_PWML3, PIOA, ID_PIOA, PIO_PERIPH_C, PIO_DEFAULT}
-/** PWM pins definition for LED0 */
-#define PIN_PWM_LED0 PIN_PWMC_PWMH0, PIN_PWMC_PWML0
-/** PWM pins definition for LED1 */
-#define PIN_PWM_LED1 PIN_PWMC_PWMH1, PIN_PWMC_PWML1
-/** PWM pins definition for LED2 */
-#define PIN_PWM_LED2 PIN_PWMC_PWMH2, PIN_PWMC_PWML2
-/** PWM channel for LED0 */
-#define CHANNEL_PWM_LED0 0
-/** PWM channel for LED1 */
-#define CHANNEL_PWM_LED1 1
-/** PWM channel for LED2 */
-#define CHANNEL_PWM_LED2 2
-
-/** SPI MISO pin definition. */
-#define PIN_SPI_MISO    {PIO_PA12A_MISO, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** SPI MOSI pin definition. */
-#define PIN_SPI_MOSI    {PIO_PA13A_MOSI, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** SPI SPCK pin definition. */
-#define PIN_SPI_SPCK    {PIO_PA14A_SPCK, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** SPI chip select pin definition. */
-#define PIN_SPI_NPCS0_PA11  {PIO_PA11A_NPCS0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** List of SPI pin definitions (MISO, MOSI & SPCK). */
-#define PINS_SPI        PIN_SPI_MISO, PIN_SPI_MOSI, PIN_SPI_SPCK
-
-/** SSC pin Transmitter Data (TD) */
-#define PIN_SSC_TD      {PIO_PA17A_TD, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** SSC pin Transmitter Clock (TK) */
-#define PIN_SSC_TK      {PIO_PA16A_TK, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** SSC pin Transmitter FrameSync (TF) */
-#define PIN_SSC_TF      {PIO_PA15A_TF, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** SSC pins definition for codec. */
-#define PINS_SSC_CODEC  PIN_SSC_TD, PIN_SSC_TK, PIN_SSC_TF
-
-/** PCK0 */
-#define PIN_PCK0        {PIO_PA6B_PCK0, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
-#define PIN_PCK1        {PIO_PA17B_PCK1,PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
-
-/** PIO PARALLEL CAPTURE */
-/** Parallel Capture Mode Data Enable1 */
-#define PIN_PIODCEN1    PIO_PA15
-/** Parallel Capture Mode Data Enable2 */
-#define PIN_PIODCEN2    PIO_PA16
-
-/** TWI ver 3.xx */
-#define TWI_V3XX
-/** TWI0 data pin */
-#define PIN_TWI_TWD0   {PIO_PA3A_TWD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** TWI0 clock pin */
-#define PIN_TWI_TWCK0  {PIO_PA4A_TWCK0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** TWI0 pins */
-#define PINS_TWI0      PIN_TWI_TWD0, PIN_TWI_TWCK0
-/** TWI1 data pin */
-#define PIN_TWI_TWD1   {PIO_PB4A_TWD1, PIOB, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT}
-/** TWI1 clock pin */
-#define PIN_TWI_TWCK1  {PIO_PB5A_TWCK1, PIOB, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT}
-/** TWI1 pins */
-#define PINS_TWI1      PIN_TWI_TWD1, PIN_TWI_TWCK1
-
-/** USART0 pin RX */
-#define PIN_USART0_RXD    {PIO_PA5A_RXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** USART0 pin TX */
-#define PIN_USART0_TXD    {PIO_PA6A_TXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** USART0 pin CTS */
-#define PIN_USART0_CTS    {PIO_PA8A_CTS0, PIOB, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT}
-/** USART0 pin RTS */
-#define PIN_USART0_RTS    {PIO_PA7A_RTS0, PIOB, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT}
-/** USART0 pin SCK */
-#define PIN_USART0_SCK    {PIO_PA2B_SCK0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-
-/** USART1 pin RX */
-#define PIN_USART1_RXD    {PIO_PA21A_RXD1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** USART1 pin TX */
-#define PIN_USART1_TXD    {PIO_PA22A_TXD1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** USART1 pin CTS */
-#define PIN_USART1_CTS    {PIO_PA25A_CTS1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** USART1 pin RTS */
-#define PIN_USART1_RTS    {PIO_PA24A_RTS1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/** USART1 pin ENABLE */
-#define PIN_USART1_EN     {PIO_PA23A_SCK1, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
-/** USART1 pin SCK */
-#define PIN_USART1_SCK    {PIO_PA23A_SCK1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-
-/** USB VBus monitoring pin definition. */
-#ifdef BOARD_REV_A
-#define PIN_USB_VBUS    {PIO_PC23, PIOC, ID_PIOC, PIO_INPUT, PIO_PULLUP}
-#endif
-
-#ifdef BOARD_REV_B
-#define PIN_USB_VBUS    {PIO_PC21, PIOC, ID_PIOC, PIO_INPUT, PIO_PULLUP}
-#endif
-
-/** NandFlash pins definition: OE. */
-#define PIN_EBI_NANDOE          {PIO_PC9,  PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
-/** NandFlash pins definition: WE. */
-#define PIN_EBI_NANDWE          {PIO_PC10, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
-/** NandFlash pins definition: CLE. */
-#define PIN_EBI_NANDCLE         {PIO_PC17, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
-/** NandFlash pins definition: ALE. */
-#define PIN_EBI_NANDALE         {PIO_PC16, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
-/** NandFlash pins definition: DATA. */
-#define PIN_EBI_NANDIO          {0x000000FF, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
-
-/** Nandflash chip enable pin definition. */
-#define BOARD_NF_CE_PIN         {PIO_PC14, PIOC, ID_PIOC, PIO_OUTPUT_1, PIO_DEFAULT}
-
-/** Nandflash controller peripheral pins definition. */
-#define PINS_NANDFLASH          PIN_EBI_NANDIO, BOARD_NF_CE_PIN, PIN_EBI_NANDOE, \
-                                PIN_EBI_NANDWE, PIN_EBI_NANDCLE, PIN_EBI_NANDALE
-
-/* PIO definitions for Slider */
-#define SLIDER_IOMASK_SNS   (uint32_t)(PIO_PA0 | PIO_PA2 | PIO_PA4)
-#define SLIDER_IOMASK_SNSK  (uint32_t)(PIO_PA1 | PIO_PA3 | PIO_PA5)
-#define PINS_SLIDER_SNS     {SLIDER_IOMASK_SNS,  PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
-#define PINS_SLIDER_SNSK    {SLIDER_IOMASK_SNSK, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
-
-/* PIO definitions for keys */
-#define KEY_IOMASK_SNS   (uint32_t)(PIO_PC22 | PIO_PC24 | PIO_PC26 | PIO_PC28 | PIO_PC30)
-#define KEY_IOMASK_SNSK  (uint32_t)(PIO_PC23 | PIO_PC25 | PIO_PC27 | PIO_PC29 | PIO_PC31)
-#define PINS_KEY_SNS     {KEY_IOMASK_SNS,  PIOC, ID_PIOC, PIO_INPUT, PIO_DEFAULT}
-#define PINS_KEY_SNSK    {KEY_IOMASK_SNSK, PIOC, ID_PIOC, PIO_INPUT, PIO_DEFAULT}
-
-/* PIOS for QTouch */
-#define PINS_QTOUCH     PINS_SLIDER_SNS, PINS_SLIDER_SNSK, PINS_KEY_SNS, PINS_KEY_SNSK
-
-
-/*----------------------------------------------------------------------------*/
-/**
- * \page sam3s_ek_usb "SAM3S-EK - USB device"
- *
- * \section Definitions
- * - \ref BOARD_USB_BMATTRIBUTES
- * - \ref CHIP_USB_UDP
- * - \ref CHIP_USB_PULLUP_INTERNAL
- * - \ref CHIP_USB_NUMENDPOINTS
- * - \ref CHIP_USB_ENDPOINTS_MAXPACKETSIZE
- * - \ref CHIP_USB_ENDPOINTS_BANKS
- */
-
-/** USB attributes configuration descriptor (bus or self powered, remote wakeup) */
-#define BOARD_USB_BMATTRIBUTES              USBConfigurationDescriptor_SELFPOWERED_RWAKEUP
-
-/** Indicates chip has an UDP Full Speed. */
-#define CHIP_USB_UDP
-
-/** Indicates chip has an internal pull-up. */
-#define CHIP_USB_PULLUP_INTERNAL
-
-/** Number of USB endpoints */
-#define CHIP_USB_NUMENDPOINTS 8
-
-/** Endpoints max paxcket size */
-#define CHIP_USB_ENDPOINTS_MAXPACKETSIZE(i) \
-   ((i == 0) ? 64 : \
-   ((i == 1) ? 64 : \
-   ((i == 2) ? 64 : \
-   ((i == 3) ? 64 : \
-   ((i == 4) ? 512 : \
-   ((i == 5) ? 512 : \
-   ((i == 6) ? 64 : \
-   ((i == 7) ? 64 : 0 ))))))))
-
-/** Endpoints Number of Bank */
-#define CHIP_USB_ENDPOINTS_BANKS(i) \
-   ((i == 0) ? 1 : \
-   ((i == 1) ? 2 : \
-   ((i == 2) ? 2 : \
-   ((i == 3) ? 1 : \
-   ((i == 4) ? 2 : \
-   ((i == 5) ? 2 : \
-   ((i == 6) ? 2 : \
-   ((i == 7) ? 2 : 0 ))))))))
-
-/*----------------------------------------------------------------------------*/
-/**
- * \page sam3s_ek_extcomp "SAM3S-EK - External components"
- * This page lists the definitions related to external on-board components
- * located in the board.h file for the AT91SAM3S-EK.
- *
- * SD Card
- * - \ref BOARD_SD_PINS
- * - \ref BOARD_SD_PIN_CD
- *
- * LCD
- * - \ref BOARD_LCD_ILI9325
- * - \ref BOARD_LCD_PINS
- * - \ref BOARD_BACKLIGHT_PIN
- * - \ref BOARD_LCD_BASE
- * - \ref BOARD_LCD_RS
- * - \ref BOARD_LCD_WIDTH
- * - \ref BOARD_LCD_HEIGHT
- *
- * TouchScreen
- * - \ref BOARD_TSC_ADS7843
- * - \ref PIN_TCS_IRQ
- * - \ref PIN_TCS_BUSY
- * - \ref BOARD_TSC_SPI_BASE
- * - \ref BOARD_TSC_SPI_ID
- * - \ref BOARD_TSC_SPI_PINS
- * - \ref BOARD_TSC_NPCS
- * - \ref BOARD_TSC_NPCS_PIN
- *
- * SmartCard
- * - \ref SMARTCARD_CONNECT_PIN
- * - \ref PIN_ISO7816_RSTMC
- * - \ref PINS_ISO7816
- */
-
-/** MCI pins that shall be configured to access the SD card. */
-#define BOARD_SD_PINS               PINS_MCI
-/** MCI Card Detect pin. */
-#define BOARD_SD_PIN_CD             PIN_MCI_CD
-
-/** Indicates board has an ILI9325 external component to manage LCD. */
-#define BOARD_LCD_ILI9325
-
-/** LCD pins definition. */
-#define BOARD_LCD_PINS              PIN_EBI_DATA_BUS, PIN_EBI_NRD, PIN_EBI_NWE, PIN_EBI_NCS1, PIN_EBI_LCD_RS
-/** Backlight pin definition. */
-#define BOARD_BACKLIGHT_PIN         {PIO_PC13, PIOC, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT}
-/** Define ILI9325 base address. */
-#define BOARD_LCD_BASE              0x61000000
-/** Define ILI9325 register select signal. */
-#define BOARD_LCD_RS                (1 << 1)
-/** Display width in pixels. */
-#define BOARD_LCD_WIDTH             240
-/** Display height in pixels. */
-#define BOARD_LCD_HEIGHT            320
-
-/** Indicates board has an ADS7843 external component to manage Touch Screen */
-#define BOARD_TSC_ADS7843
-
-/** Touchscreen controller IRQ pin definition. */
-#ifdef BOARD_REV_A
-#define PIN_TSC_IRQ  {PIO_PA4, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP}
-#define PIN_TSC_IRQ_WUP_ID (1 << 3)
-/** Touchscreen controller Busy pin definition. */
-#define PIN_TSC_BUSY {PIO_PA5, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP}
-#endif
-
-#ifdef BOARD_REV_B
-#define PIN_TSC_IRQ  {PIO_PA16, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP}
-#define PIN_TSC_IRQ_WUP_ID (1 << 15)
-/** Touchscreen controller Busy pin definition. */
-#define PIN_TSC_BUSY {PIO_PA17, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP}
-#endif
-
-/** Base address of SPI peripheral connected to the touchscreen controller. */
-#define BOARD_TSC_SPI_BASE         SPI
-/** Identifier of SPI peripheral connected to the touchscreen controller. */
-#define BOARD_TSC_SPI_ID           ID_SPI
-/** Pins of the SPI peripheral connected to the touchscreen controller. */
-#define BOARD_TSC_SPI_PINS         PINS_SPI
-/** Chip select connected to the touchscreen controller. */
-#define BOARD_TSC_NPCS             0
-/** Chip select pin connected to the touchscreen controller. */
-#define BOARD_TSC_NPCS_PIN         PIN_SPI_NPCS0_PA11
-
-/// Smartcard detection pin
-//#define SMARTCARD_CONNECT_PIN {1 << 13, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
-
-/// PIN used for reset the smartcard
-#define PIN_ISO7816_RSTMC       {1 << 11, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
-/// Pins used for connect the smartcard
-#define PINS_ISO7816            PIN_USART1_TXD, PIN_USART1_SCK, PIN_ISO7816_RSTMC
-
-/*----------------------------------------------------------------------------*/
-/**
- * \page sam3s_ek_mem "SAM3S-EK - Memories"
- * This page lists definitions related to internal & external on-board memories.
- *
- * \section SRAM
- * - \ref AT91C_ISRAM
- * - \ref AT91C_ISRAM_SIZE
- *
- * \section Flash
- * - \ref AT91C_IFLASH_SIZE
- * - \ref AT91C_IFLASH_PAGE_SIZE
- * - \ref AT91C_IFLASH_NB_OF_PAGES
- * - \ref AT91C_IFLASH_LOCK_REGION_SIZE
- * - \ref AT91C_IFLASH_NB_OF_LOCK_BITS
- *
- * \section NandFlash
- * - \ref BOARD_NF_COMMAND_ADDR
- * - \ref BOARD_NF_ADDRESS_ADDR
- * - \ref BOARD_NF_DATA_ADDR
- *
- * \section NorFlash
- * - \ref BOARD_NORFLASH_ADDR
- * - \ref BOARD_NORFLASH_DFT_BUS_SIZE
- */
-
-/** Address for transferring command bytes to the nandflash. */
-#define BOARD_NF_COMMAND_ADDR   0x60400000
-/** Address for transferring address bytes to the nandflash. */
-#define BOARD_NF_ADDRESS_ADDR   0x60200000
-/** Address for transferring data bytes to the nandflash. */
-#define BOARD_NF_DATA_ADDR      0x60000000
-
-/** Address for transferring command bytes to the norflash. */
-#define BOARD_NORFLASH_ADDR     0x63000000
-/** Default NOR bus size after power up reset */
-#define BOARD_NORFLASH_DFT_BUS_SIZE 8
-
-/*----------------------------------------------------------------------------*/
-/**
- * \page sam3s_ek_chipdef "SAM3S-EK - Individual chip definition"
- * This page lists the definitions related to different chip's definition
- * located in the board.h file for the SAM3S-EK.
- *
- * \section USART
- * - \ref BOARD_PIN_USART_RXD
- * - \ref BOARD_PIN_USART_TXD
- * - \ref BOARD_PIN_USART_CTS
- * - \ref BOARD_PIN_USART_RTS
- * - \ref BOARD_PIN_USART_EN
- * - \ref BOARD_USART_BASE
- * - \ref BOARD_ID_USART
- */
-
-/** Rtc */
-#define BOARD_RTC_ID                ID_RTC
-
-/** TWI ID for EEPROM application to use */
-#define BOARD_ID_TWI_EEPROM         ID_TWI1
-/** TWI ID for SLAVE application to use */
-#define BOARD_ID_TWI_SLAVE          ID_TWI1
-/** TWI Base for TWI EEPROM application to use */
-#define BOARD_BASE_TWI_EEPROM       TWI1
-/** TWI Base for TWI SLAVE application to use */
-#define BOARD_BASE_TWI_SLAVE        TWI1
-/** TWI pins for EEPROM application to use */
-#define BOARD_PINS_TWI_EEPROM       PINS_TWI1
-/** TWI pins for TWI SLAVE application to use */
-#define BOARD_PINS_TWI_SLAVE        PINS_TWI1
-
-/** USART RX pin for application */
-#define BOARD_PIN_USART_RXD        PIN_USART1_RXD
-/** USART TX pin for application */
-#define BOARD_PIN_USART_TXD        PIN_USART1_TXD
-/** USART CTS pin for application */
-#define BOARD_PIN_USART_CTS        PIN_USART1_CTS
-/** USART RTS pin for application */
-#define BOARD_PIN_USART_RTS        PIN_USART1_RTS
-/** USART ENABLE pin for application */
-#define BOARD_PIN_USART_EN         PIN_USART1_EN
-/** USART Base for application */
-#define BOARD_USART_BASE           USART1
-/** USART ID for application */
-#define BOARD_ID_USART             ID_USART1
-
-#endif /* #ifndef _BOARD_ */
-

applets/libraries/libboard_atsam3s-ek/include/board_lowlevel.h

@@ -1,46 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2009, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-/**
- * \file
- *
- * Interface for the low-level initialization function.
- *
- */
-
-#ifndef BOARD_LOWLEVEL_H
-#define BOARD_LOWLEVEL_H
-
-/*----------------------------------------------------------------------------
- *        Exported functions
- *----------------------------------------------------------------------------*/
-extern void LowLevelInit( void ) ;
-
-#endif /* BOARD_LOWLEVEL_H */
-

applets/libraries/libboard_atsam3s-ek/resources/gcc/atsam3s1/sram.lds

@@ -1,81 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2009, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-/*------------------------------------------------------------------------------
- *      Linker script for running in internal SRAM on the AT91SAM3S1
- *----------------------------------------------------------------------------*/
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(ResetException)
-
-/* Memory Spaces Definitions */
-MEMORY
-{
-    sram (W!RX) : ORIGIN = 0x20000000, LENGTH = 0x00004000 /* sram, 16K */
-}
-
-SECTIONS
-{
-    .fixed :
-    {
-        . = ALIGN(4);
-        _sfixed = .;
-        KEEP(*(.vectors))
-        *(.text*)
-        *(.ramfunc)
-        *(.rodata*)
-        *(.glue_7)
-        *(.glue_7t)
-        . = ALIGN(4);
-        _efixed = .;            /* End of text section */
-    } > sram
-
-    .relocate : AT (_efixed)
-    {
-        . = ALIGN(4);
-        _srelocate = .;
-        *(.data)
-        . = ALIGN(4);
-        _erelocate = .;
-    } >sram
-
-    .bss (NOLOAD) : {
-        . = ALIGN(4);
-        _szero = .;
-        *(.bss)
-        . = ALIGN(4);
-        _ezero = .;
-    } >sram
-
-    /* Stack in the end of SRAM */
-    _estack = 0x20003FFC;
-
-}
-end = .;

applets/libraries/libboard_atsam3s-ek/resources/gcc/atsam3s1/sram_samba.lds

@@ -1,91 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2009, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-/*------------------------------------------------------------------------------
- *      Linker script for running in internal SRAM on the AT91SAM3S1
- *----------------------------------------------------------------------------*/
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(entry)
-
-/* Memory Spaces Definitions */
-MEMORY
-{
-    romcodesram (W!RX) : ORIGIN = 0x20000000, LENGTH = 0x0800
-    sram (W!RX) : ORIGIN = 0x20000800, LENGTH = 0x00003800 /* sram, 16K - sizeof(romcodesram) */
-}
-
-/* Entry point */
-/*ENTRY (ResetException)*/
-
-SECTIONS
-{
-    /* startup code in the .isr_vector */
-    .text :
-    {
-        . = ALIGN(4);
-        _stext = .;
-        KEEP(*(.isr_vector .isr_vector.*))
-        *(.mailbox)
-        *(.text .text.*)
-        *(.rodata .rodata.*)
-        *(.glue_7)
-        *(.glue_7t)
-        *(.gcc_except_table)
-        *(.rodata .rodata*)
-        *(.gnu.linkonce.r.*)
-        . = ALIGN(4);
-        _etext = .;
-    } > sram
-
-    /* data */
-    .data :
-    {
-        . = ALIGN(4);
-        _sidata = .;
-        _sdata = .;
-
-        *(.data)
-        *(.data.*)
-        . = ALIGN(4);
-        _edata = .;
-    } > sram
-
-    .bss (NOLOAD) : {
-        _szero = .;
-        *(.bss)
-        . = ALIGN(4);
-        _ezero = .;
-    } >sram
-
-    /* Stack in SRAM */
-    _sstack = 0x20003FFC;
-}
-end = .;

applets/libraries/libboard_atsam3s-ek/resources/gcc/atsam3s2/sram.lds

@@ -1,81 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2009, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-/*------------------------------------------------------------------------------
- *      Linker script for running in internal SRAM on the AT91SAM3S2
- *----------------------------------------------------------------------------*/
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(ResetException)
-
-/* Memory Spaces Definitions */
-MEMORY
-{
-    sram (W!RX) : ORIGIN = 0x20000000, LENGTH = 0x00008000 /* sram, 32K */
-}
-
-SECTIONS
-{
-    .fixed :
-    {
-        . = ALIGN(4);
-        _sfixed = .;
-        KEEP(*(.vectors))
-        *(.text*)
-        *(.ramfunc)
-        *(.rodata*)
-        *(.glue_7)
-        *(.glue_7t)
-        . = ALIGN(4);
-        _efixed = .;            /* End of text section */
-    } > sram
-
-    .relocate : AT (_efixed)
-    {
-        . = ALIGN(4);
-        _srelocate = .;
-        *(.data)
-        . = ALIGN(4);
-        _erelocate = .;
-    } >sram
-
-    .bss (NOLOAD) : {
-        . = ALIGN(4);
-        _szero = .;
-        *(.bss)
-        . = ALIGN(4);
-        _ezero = .;
-    } >sram
-
-    /* Stack in the end of SRAM */
-    _estack = 0x20007FFC;
-
-}
-end = .;

applets/libraries/libboard_atsam3s-ek/resources/gcc/atsam3s2/sram_samba.lds

@@ -1,91 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2009, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-/*------------------------------------------------------------------------------
- *      Linker script for running in internal SRAM on the AT91SAM3S2
- *----------------------------------------------------------------------------*/
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(entry)
-
-/* Memory Spaces Definitions */
-MEMORY
-{
-    romcodesram (W!RX) : ORIGIN = 0x20000000, LENGTH = 0x0800
-    sram (W!RX) : ORIGIN = 0x20000800, LENGTH = 0x00007800 /* sram, 32K - sizeof(romcodesram) */
-}
-
-/* Entry point */
-/*ENTRY (ResetException)*/
-
-SECTIONS
-{
-    /* startup code in the .isr_vector */
-    .text :
-    {
-        . = ALIGN(4);
-        _stext = .;
-        KEEP(*(.isr_vector .isr_vector.*))
-        *(.mailbox)
-        *(.text .text.*)
-        *(.rodata .rodata.*)
-        *(.glue_7)
-        *(.glue_7t)
-        *(.gcc_except_table)
-        *(.rodata .rodata*)
-        *(.gnu.linkonce.r.*)
-        . = ALIGN(4);
-        _etext = .;
-    } > sram
-
-    /* data */
-    .data :
-    {
-        . = ALIGN(4);
-        _sidata = .;
-        _sdata = .;
-
-        *(.data)
-        *(.data.*)
-        . = ALIGN(4);
-        _edata = .;
-    } > sram
-
-    .bss (NOLOAD) : {
-        _szero = .;
-        *(.bss)
-        . = ALIGN(4);
-        _ezero = .;
-    } >sram
-
-    /* Stack in SRAM */
-    _sstack = 0x20007FFC;
-}
-end = .;

applets/libraries/libboard_atsam3s-ek/resources/gcc/atsam3s4/sram.lds

@@ -1,215 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2009, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-/*------------------------------------------------------------------------------
- *      Linker script for running in internal SRAM on the AT91SAM3S4
- *----------------------------------------------------------------------------*/
-
-OUTPUT_FORMAT ("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-ENTRY(_start)
-SEARCH_DIR(.)
-GROUP(-lgcc -lc -lcs3 -lcs3unhosted -lcs3micro)
-
-/* Memory Spaces Definitions */
-MEMORY
-{
-    sram (W!RX) : ORIGIN = 0x20000000, LENGTH = 0x0000C000 /* sram, 48K */
-}
-
-/* These force the linker to search for particular symbols from
- * the start of the link process and thus ensure the user's
- * overrides are picked up
- */
-EXTERN(__cs3_reset_generic_m)
-INCLUDE atsam3s.inc
-EXTERN(__cs3_interrupt_vector_micro)
-EXTERN(__cs3_start_c main __cs3_stack __cs3_heap_end)
-
-PROVIDE(__cs3_heap_start = _end);
-PROVIDE(__cs3_heap_end = __cs3_region_start_ram + __cs3_region_size_ram);
-PROVIDE(__cs3_region_num = (__cs3_regions_end - __cs3_regions) / 20);
-PROVIDE(__cs3_stack = __cs3_region_start_ram + __cs3_region_size_ram);
-
-SECTIONS
-{
-
-  .text :
-  {
-    CREATE_OBJECT_SYMBOLS
-    __cs3_region_start_ram = .;
-    *(.cs3.region-head.ram)
-    ASSERT (. == __cs3_region_start_ram, ".cs3.region-head.ram not permitted");
-    __cs3_interrupt_vector = __cs3_interrupt_vector_micro;
-    *(.cs3.interrupt_vector)
-    /* Make sure we pulled in an interrupt vector.  */
-    ASSERT (. != __cs3_interrupt_vector_micro, "No interrupt vector");
-
-    _start = __cs3_reset_generic_m;
-    __cs3_reset = __cs3_reset_generic_m;
-    *(.cs3.reset)
-    /* Make sure we pulled in some reset code.  */
-    ASSERT (. != __cs3_reset, "No reset code");
-
-    *(.text .text.* .gnu.linkonce.t.*)
-    *(.plt)
-    *(.gnu.warning)
-    *(.glue_7t) *(.glue_7) *(.vfp11_veneer)
-
-    *(.ARM.extab* .gnu.linkonce.armextab.*)
-    *(.gcc_except_table)
-  } >ram
-  .eh_frame_hdr : ALIGN (4)
-  {
-    KEEP (*(.eh_frame_hdr))
-  } >ram
-  .eh_frame : ALIGN (4)
-  {
-    KEEP (*(.eh_frame))
-  } >ram
-  /* .ARM.exidx is sorted, so has to go in its own output section.  */
-  __exidx_start = .;
-  .ARM.exidx :
-  {
-    *(.ARM.exidx* .gnu.linkonce.armexidx.*)
-  } >ram
-  __exidx_end = .;
-  .rodata : ALIGN (4)
-  {
-    *(.rodata .rodata.* .gnu.linkonce.r.*)
-
-    . = ALIGN(4);
-    KEEP(*(.init))
-
-    . = ALIGN(4);
-    __preinit_array_start = .;
-    KEEP (*(.preinit_array))
-    __preinit_array_end = .;
-
-    . = ALIGN(4);
-    __init_array_start = .;
-    KEEP (*(SORT(.init_array.*)))
-    KEEP (*(.init_array))
-    __init_array_end = .;
-
-    . = ALIGN(4);
-    KEEP(*(.fini))
-
-    . = ALIGN(4);
-    __fini_array_start = .;
-    KEEP (*(.fini_array))
-    KEEP (*(SORT(.fini_array.*)))
-    __fini_array_end = .;
-
-    . = ALIGN(0x4);
-    KEEP (*crtbegin.o(.ctors))
-    KEEP (*(EXCLUDE_FILE (*crtend.o) .ctors))
-    KEEP (*(SORT(.ctors.*)))
-    KEEP (*crtend.o(.ctors))
-
-    . = ALIGN(0x4);
-    KEEP (*crtbegin.o(.dtors))
-    KEEP (*(EXCLUDE_FILE (*crtend.o) .dtors))
-    KEEP (*(SORT(.dtors.*)))
-    KEEP (*crtend.o(.dtors))
-
-    . = ALIGN(4);
-    __cs3_regions = .;
-    LONG (0)
-    LONG (__cs3_region_init_ram)
-    LONG (__cs3_region_start_ram)
-    LONG (__cs3_region_init_size_ram)
-    LONG (__cs3_region_zero_size_ram)
-    __cs3_regions_end = .;
-
-    . = ALIGN (8);
-    _etext = .;
-  } >ram
-
-  .data : ALIGN (8)
-  {
-
-    KEEP(*(.jcr))
-    *(.got.plt) *(.got)
-    *(.shdata)
-    *(.data .data.* .gnu.linkonce.d.*)
-    . = ALIGN (8);
-    *(.ram)
-    _edata = .;
-  } >ram
-  .bss :
-  {
-    *(.shbss)
-    *(.bss .bss.* .gnu.linkonce.b.*)
-    *(COMMON)
-    . = ALIGN (8);
-    *(.ram.b)
-    _end = .;
-    __end = .;
-  } >ram
-  __cs3_region_init_ram = __cs3_region_start_ram;
-  __cs3_region_init_size_ram = _edata - __cs3_region_start_ram;
-  __cs3_region_zero_size_ram = _end - _edata;
-  /* Default to 1M of heap */
-  __cs3_region_size_ram = ALIGN (1024) - __cs3_region_start_ram + 1M;
-
-  .stab 0 (NOLOAD) : { *(.stab) }
-  .stabstr 0 (NOLOAD) : { *(.stabstr) }
-  /* DWARF debug sections.
-   * Symbols in the DWARF debugging sections are relative to the beginning
-   * of the section so we begin them at 0.  */
-  /* DWARF 1 */
-  .debug          0 : { *(.debug) }
-  .line           0 : { *(.line) }
-  /* GNU DWARF 1 extensions */
-  .debug_srcinfo  0 : { *(.debug_srcinfo) }
-  .debug_sfnames  0 : { *(.debug_sfnames) }
-  /* DWARF 1.1 and DWARF 2 */
-  .debug_aranges  0 : { *(.debug_aranges) }
-  .debug_pubnames 0 : { *(.debug_pubnames) }
-  /* DWARF 2 */
-  .debug_info     0 : { *(.debug_info .gnu.linkonce.wi.*) }
-  .debug_abbrev   0 : { *(.debug_abbrev) }
-  .debug_line     0 : { *(.debug_line) }
-  .debug_frame    0 : { *(.debug_frame) }
-  .debug_str      0 : { *(.debug_str) }
-  .debug_loc      0 : { *(.debug_loc) }
-  .debug_macinfo  0 : { *(.debug_macinfo) }
-  /* DWARF 2.1 */
-  .debug_ranges   0 : { *(.debug_ranges) }
-  /* SGI/MIPS DWARF 2 extensions */
-  .debug_weaknames 0 : { *(.debug_weaknames) }
-  .debug_funcnames 0 : { *(.debug_funcnames) }
-  .debug_typenames 0 : { *(.debug_typenames) }
-  .debug_varnames  0 : { *(.debug_varnames) }
-
-  .note.gnu.arm.ident 0 : { KEEP (*(.note.gnu.arm.ident)) }
-  .ARM.attributes 0 : { KEEP (*(.ARM.attributes)) }
-  /DISCARD/ : { *(.note.GNU-stack) }
-}
-/* checksum: 576d003e2604ff7a1b02791267 */

applets/libraries/libboard_atsam3s-ek/resources/gcc/atsam3s4/sram_samba.lds

@@ -1,91 +0,0 @@
-/* ----------------------------------------------------------------------------
- *         ATMEL Microcontroller Software Support
- * ----------------------------------------------------------------------------
- * Copyright (c) 2009, Atmel Corporation
- *
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * - Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the disclaimer below.
- *
- * Atmel's name may not be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
- * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- * ----------------------------------------------------------------------------
- */
-
-/*------------------------------------------------------------------------------
- *      Linker script for running in internal SRAM on the AT91SAM3S4
- *----------------------------------------------------------------------------*/
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(entry)
-
-/* Memory Spaces Definitions */
-MEMORY
-{
-    romcodesram (W!RX) : ORIGIN = 0x20000000, LENGTH = 0x01000
-    sram (W!RX) : ORIGIN = 0x20001000, LENGTH = 0x0000B000 /* sram, 48K - sizeof(romcodesram) */
-}
-
-/* Entry point */
-/*ENTRY (ResetException)*/
-
-SECTIONS
-{
-    /* startup code in the .isr_vector */
-    .text :
-    {
-        . = ALIGN(4);
-        _stext = .;
-        KEEP(*(.isr_vector .isr_vector.*))
-        *(.mailbox)
-        *(.text .text.*)
-        *(.rodata .rodata.*)
-        *(.glue_7)
-        *(.glue_7t)
-        *(.gcc_except_table)
-        *(.rodata .rodata*)
-        *(.gnu.linkonce.r.*)
-        . = ALIGN(4);
-        _etext = .;
-    } > sram
-
-    /* data */
-    .data :
-    {
-        . = ALIGN(4);
-        _sidata = .;
-        _sdata = .;
-
-        *(.data)
-        *(.data.*)
-        . = ALIGN(4);
-        _edata = .;
-    } > sram
-
-    .bss (NOLOAD) : {
-        _szero = .;
-        *(.bss)
-        . = ALIGN(4);
-        _ezero = .;
-    } >sram
-
-    /* Stack in SRAM */
-    _sstack = 0x2000BFFC;
-}
-end = .;

applets/libraries/libchip_atsam3s/chip.h

@@ -1,63 +0,0 @@
-#ifndef _LIB_ATSAM3S_
-#define _LIB_ATSAM3S_
-
-/*
- * Peripherals registers definitions
- */
-#if defined atsam3s4
-    #include <include/ATSAM3S4.h>
-#elif defined atsam3s2
-    #include <include/ATSAM3S2.h>
-#elif defined atsam3s1
-    #include <include/ATSAM3S1.h>
-#else
-    #warning Library does not support the specified chip, specifying atsam3s4.
-    #define atsam3s4
-    #include <include/ATSAM3S4.h>
-#endif
-
-
-/* Define attribute */
-#if defined   ( __CC_ARM   ) /* Keil µVision 4 */
-    #define WEAK __attribute__ ((weak))
-#elif defined ( __ICCARM__ ) /* IAR Ewarm 5.41+ */
-    #define WEAK __weak
-#elif defined (  __GNUC__  ) /* GCC CS3 2009q3-68 */
-    #define WEAK __attribute__ ((weak))
-#endif
-
-/* Define NO_INIT attribute */
-#if defined   ( __CC_ARM   )
-    #define NO_INIT
-#elif defined ( __ICCARM__ )
-    #define NO_INIT __no_init
-#elif defined (  __GNUC__  )
-    #define NO_INIT
-#endif
-
-/*
- * Core
- */
-
-/*
- * Peripherals
- */
-//#include <include/async.h>
-//#include <include/efc.h>
-//#include <include/flashd.h>
-//#include <include/pio.h>
-//#include <include/pmc.h>
-//#include <include/spi.h>
-//#include <include/spi_pdc.h>
-//#include <include/twi.h>
-//#include <include/twid.h>
-//#include <include/usart.h>
-
-/*
-#include <USBD_Config.h>
-*/
-
-//#include <include/trace.h>
-//#include <include/wdt.h>
-
-#endif /* _LIB_ATSAM3S_ */

src/Makefile

@@ -63,6 +63,10 @@ PCBREV =
 # Values = STD, FRSKY, JETI, NMEA, ARDUPILOT, MAVLINK, TELEMETREZ
 EXT = STD
 
+# FAI mode
+# Values = YES, NO, CHOICE
+FAI = NO
+
 # Enable heli menu
 # Values = YES, NO
 HELI = NO
@@ -71,12 +75,13 @@ HELI = NO
 # Values = YES, NO
 TEMPLATES = YES
 
-# Enable navigation with Pots / Rotary encoders
+# Enable navigation with Pots / Sticks / Rotary encoders
 # Values = NO
 #          POT1 (only POT1 available for fields modification),
 #          POT2 (menus scroll),
 #          POT3 (cursor down/up),
 #          POTS (POT1, POT2, POT3),
+#          STICKS
 #          ROTENC (Rotary encoder)
 NAVIGATION = NO
 
@@ -328,7 +333,7 @@ ifeq ($(PCB), $(filter $(PCB), STD128 9X128 9XR128))
   EXTRABOARDSRC = targets/stock/lcd_driver.cpp
   EEPROMSRC = eeprom_common.cpp eeprom_rlc.cpp
   PULSESSRC = protocols/pulses_avr.cpp
-
+  
   ifeq ($(PCB), 9XR128)
     CPPDEFS += -DPCB9XR128
   else
@@ -532,7 +537,7 @@ ifeq ($(PCB), SKY9X)
   SRC += targets/sky9x/MEDSdcard.c
   EEPROMSRC = eeprom_common.cpp eeprom_raw.cpp eeprom_conversions.cpp
   PULSESSRC = protocols/pulses_arm.cpp protocols/ppm_arm.cpp protocols/pxx_arm.cpp protocols/dsm2_arm.cpp
-  CPPSRC += audio_arm.cpp haptic.cpp
+  CPPSRC += audio_arm.cpp haptic.cpp gui/view_about.cpp
   CPPSRC += targets/sky9x/pwr_driver.cpp targets/sky9x/adc_driver.cpp targets/sky9x/coproc_driver.cpp targets/sky9x/rotenc_driver.cpp targets/sky9x/eeprom_driver.cpp targets/sky9x/pulses_driver.cpp targets/sky9x/keys_driver.cpp targets/sky9x/audio_driver.cpp targets/sky9x/buzzer_driver.cpp targets/sky9x/haptic_driver.cpp targets/sky9x/sdcard_driver.cpp targets/sky9x/massstorage.cpp
   
   ifeq ($(SDCARD), YES)
@@ -615,7 +620,6 @@ ifeq ($(PCB), TARANIS)
   SRC += targets/taranis/STM32_USB-Host-Device_Lib_V2.1.0/Libraries/STM32_USB_Device_Library/Class/msc/src/usbd_msc_scsi.c
   SRC += targets/taranis/STM32_USB-Host-Device_Lib_V2.1.0/Libraries/STM32_USB_Device_Library/Class/msc/src/usbd_msc_bot.c
   SRC += targets/taranis/STM32_USB-Host-Device_Lib_V2.1.0/Libraries/STM32_USB_Device_Library/Class/msc/src/usbd_msc_core.c
-  # SRC += targets/taranis/STM32_USB-Host-Device_Lib_V2.1.0/Libraries/STM32_USB_Device_Library/Class/hid/src/usbd_hid_core.c
   EXTRABOARDSRC += targets/taranis/usbd_usr.cpp targets/taranis/usbd_storage_msd.cpp
   
   ifeq ($(SDCARD), YES)
@@ -634,6 +638,10 @@ ifeq ($(PCB), TARANIS)
   	SRC += targets/sky9x/syscalls.c
   endif
   
+  ifeq ($(DSM2), PPM)
+    CPPSRC += protocols/dsm2_arm.cpp
+  endif
+  
   ifeq ($(HUBSAN), YES)
     CPPDEFS += -DHUBSAN
     CPPSRC += protocols/hubsan.cpp
@@ -710,6 +718,9 @@ endif
 ifeq ($(NAVIGATION), POTS)
   CPPDEFS += -DNAVIGATION_POT1 -DNAVIGATION_POT2 -DNAVIGATION_POT3
 endif
+ifeq ($(NAVIGATION), STICKS)
+  CPPDEFS += -DNAVIGATION_STICKS
+endif
 ifeq ($(NAVIGATION), ROTENC)
   CPPDEFS += -DROTARY_ENCODER_NAVIGATION
 endif
@@ -889,6 +900,13 @@ ifeq ($(PPM_UNIT), PERCENT_PREC0)
   CPPDEFS += -DPPM_UNIT_PERCENT_PREC0
 endif
 
+ifeq ($(FAI), YES)
+  CPPDEFS += -DFAI
+endif
+ifeq ($(FAI), CHOICE)
+  CPPDEFS += -DFAI_CHOICE
+endif
+
 ifeq ($(HELI), YES)
   CPPDEFS += -DHELI
 endif
@@ -1016,7 +1034,7 @@ else
   build: stamp_header lbm allsrc.cpp elf remallsrc bin lss
 endif
 
-lbm: bitmaps/font.lbm bitmaps/sticks.lbm
+lbm: fonts/std/font_05x07.lbm bitmaps/sticks.lbm
   
 elf: $(TARGET).elf
 bin: $(TARGET).bin
@@ -1071,30 +1089,48 @@ taranis-stamp:
 	@echo "#define SVN_VERS \"opentx-r$(SVNREV)\"" >> stamp-opentx-taranis.txt
 	@cat stamp-opentx-taranis.txt
 
-bitmaps/font.lbm: bitmaps/font.xbm bitmaps/font_extra.xbm bitmaps/font_tiny.xbm bitmaps/font_small.xbm bitmaps/font_midsize.xbm bitmaps/font_dblsize.xbm bitmaps/font_dblsize_extra.xbm bitmaps/font_small_extra.xbm translations/font_se.xbm translations/font_de.xbm translations/font_it.xbm translations/font_cz.xbm translations/font_fr.xbm translations/font_es.xbm translations/font_dblsize_se.xbm translations/font_dblsize_de.xbm translations/font_dblsize_it.xbm translations/font_dblsize_fr.xbm translations/font_dblsize_es.xbm
+fonts/std/font_05x07.lbm: fonts/std/font_03x05.png fonts/std/font_04x06.png fonts/std/font_05x07.png fonts/std/font_08x10.png fonts/std/font_10x14.png fonts/std/font_10x14_compressed.png fonts/std/font_04x06_extra.png fonts/std/font_05x07_extra.png fonts/std/font_10x14_extra.png fonts/std/font_se_05x07.png fonts/std/font_de_05x07.png fonts/std/font_it_05x07.png fonts/std/font_cz_05x07.png fonts/std/font_fr_05x07.png fonts/std/font_es_05x07.png fonts/std/font_se_10x14.png fonts/std/font_de_10x14.png fonts/std/font_it_10x14.png fonts/std/font_fr_10x14.png fonts/std/font_es_10x14.png 
 	@echo
-	@echo "Convert fonts from xbm to lbm:"
-	$(IMG2LBM) bitmaps/font.xbm bitmaps/font.lbm 5x7
-	$(IMG2LBM) bitmaps/font_extra.xbm bitmaps/font_extra.lbm 5x7
-	$(IMG2LBM) bitmaps/font_tiny.xbm bitmaps/font_tiny.lbm 3x5
-	$(IMG2LBM) bitmaps/font_small.xbm bitmaps/font_small.lbm 4x6
-	$(IMG2LBM) bitmaps/font_midsize.xbm bitmaps/font_midsize.lbm 8x10
-	$(IMG2LBM) bitmaps/font_dblsize.xbm bitmaps/font_dblsize.lbm 10x14
-	$(IMG2LBM) bitmaps/font_dblsize_extra.xbm bitmaps/font_dblsize_extra.lbm 10x14
-	$(IMG2LBM) bitmaps/font_small_extra.xbm bitmaps/font_small_extra.lbm 4x6
-	$(IMG2LBM) translations/font_se.xbm translations/font_se.lbm 5x7
-	$(IMG2LBM) translations/font_de.xbm translations/font_de.lbm 5x7
-	$(IMG2LBM) translations/font_it.xbm translations/font_it.lbm 5x7
-	$(IMG2LBM) translations/font_cz.xbm translations/font_cz.lbm 5x7
-	$(IMG2LBM) translations/font_fr.xbm translations/font_fr.lbm 5x7
-	$(IMG2LBM) translations/font_es.xbm translations/font_es.lbm 5x7
-	$(IMG2LBM) translations/font_dblsize_se.xbm translations/font_dblsize_se.lbm 10x14
-	$(IMG2LBM) translations/font_dblsize_de.xbm translations/font_dblsize_de.lbm 10x14
-	$(IMG2LBM) translations/font_dblsize_it.xbm translations/font_dblsize_it.lbm 10x14
-	$(IMG2LBM) translations/font_dblsize_fr.xbm translations/font_dblsize_fr.lbm 10x14
-	$(IMG2LBM) translations/font_dblsize_es.xbm translations/font_dblsize_es.lbm 10x14
+	@echo "Convert fonts from png to lbm:"
+	$(IMG2LBM) fonts/std/font_03x05.png fonts/std/font_03x05.lbm 3x5
+	$(IMG2LBM) fonts/std/font_04x06.png fonts/std/font_04x06.lbm 4x6
+	$(IMG2LBM) fonts/std/font_05x07.png fonts/std/font_05x07.lbm 5x7
+	$(IMG2LBM) fonts/std/font_08x10.png fonts/std/font_08x10.lbm 8x10
+	$(IMG2LBM) fonts/std/font_10x14.png fonts/std/font_10x14.lbm 10x14
+	$(IMG2LBM) fonts/std/font_10x14_compressed.png fonts/std/font_10x14_compressed.lbm 10x14
+	$(IMG2LBM) fonts/std/font_04x06_extra.png fonts/std/font_04x06_extra.lbm 4x6
+	$(IMG2LBM) fonts/std/font_05x07_extra.png fonts/std/font_05x07_extra.lbm 5x7
+	$(IMG2LBM) fonts/std/font_10x14_extra.png fonts/std/font_10x14_extra.lbm 10x14
+	$(IMG2LBM) fonts/std/font_cz_04x06.png fonts/std/font_cz_04x06.lbm 4x6
+	$(IMG2LBM) fonts/std/font_cz_05x07.png fonts/std/font_cz_05x07.lbm 5x7
+	$(IMG2LBM) fonts/std/font_cz_08x10.png fonts/std/font_cz_08x10.lbm 8x10
+	$(IMG2LBM) fonts/std/font_cz_10x14.png fonts/std/font_cz_10x14.lbm 10x14
+	$(IMG2LBM) fonts/std/font_de_04x06.png fonts/std/font_de_04x06.lbm 4x6
+	$(IMG2LBM) fonts/std/font_de_05x07.png fonts/std/font_de_05x07.lbm 5x7
+	$(IMG2LBM) fonts/std/font_de_08x10.png fonts/std/font_de_08x10.lbm 8x10
+	$(IMG2LBM) fonts/std/font_de_10x14.png fonts/std/font_de_10x14.lbm 10x14
+	$(IMG2LBM) fonts/std/font_es_04x06.png fonts/std/font_es_04x06.lbm 4x6
+	$(IMG2LBM) fonts/std/font_es_05x07.png fonts/std/font_es_05x07.lbm 5x7
+	$(IMG2LBM) fonts/std/font_es_08x10.png fonts/std/font_es_08x10.lbm 8x10
+	$(IMG2LBM) fonts/std/font_es_10x14.png fonts/std/font_es_10x14.lbm 10x14
+	$(IMG2LBM) fonts/std/font_fr_04x06.png fonts/std/font_fr_04x06.lbm 4x6
+	$(IMG2LBM) fonts/std/font_fr_05x07.png fonts/std/font_fr_05x07.lbm 5x7
+	$(IMG2LBM) fonts/std/font_fr_08x10.png fonts/std/font_fr_08x10.lbm 8x10
+	$(IMG2LBM) fonts/std/font_fr_10x14.png fonts/std/font_fr_10x14.lbm 10x14
+	$(IMG2LBM) fonts/std/font_it_04x06.png fonts/std/font_it_04x06.lbm 4x6
+	$(IMG2LBM) fonts/std/font_it_05x07.png fonts/std/font_it_05x07.lbm 5x7
+	$(IMG2LBM) fonts/std/font_it_08x10.png fonts/std/font_it_08x10.lbm 8x10
+	$(IMG2LBM) fonts/std/font_it_10x14.png fonts/std/font_it_10x14.lbm 10x14
+	$(IMG2LBM) fonts/std/font_pt_04x06.png fonts/std/font_pt_04x06.lbm 4x6
+	$(IMG2LBM) fonts/std/font_pt_05x07.png fonts/std/font_pt_05x07.lbm 5x7
+	$(IMG2LBM) fonts/std/font_pt_08x10.png fonts/std/font_pt_08x10.lbm 8x10
+	$(IMG2LBM) fonts/std/font_pt_10x14.png fonts/std/font_pt_10x14.lbm 10x14
+	$(IMG2LBM) fonts/std/font_se_04x06.png fonts/std/font_se_04x06.lbm 4x6
+	$(IMG2LBM) fonts/std/font_se_05x07.png fonts/std/font_se_05x07.lbm 5x7
+	$(IMG2LBM) fonts/std/font_se_08x10.png fonts/std/font_se_08x10.lbm 8x10
+	$(IMG2LBM) fonts/std/font_se_10x14.png fonts/std/font_se_10x14.lbm 10x14
 
-bitmaps/sticks.lbm: bitmaps/sticks_4x1.xbm bitmaps/splash_9x.xbm bitmaps/splash_taranis.png bitmaps/logo_taranis.bmp bitmaps/icons.png bitmaps/asterisk.xbm bitmaps/about.png bitmaps/asterisk_4bits.png
+bitmaps/sticks.lbm: bitmaps/sticks_4x1.xbm bitmaps/splash_9x.xbm bitmaps/splash_taranis.png bitmaps/logo_taranis.bmp bitmaps/icons.png bitmaps/asterisk.xbm bitmaps/about_9x.png bitmaps/about_taranis.png bitmaps/asterisk_4bits.png
 	@echo
 	@echo "Convert bitmaps from xbm to lbm:"
 	$(IMG2LBM) bitmaps/sticks_4x1.xbm bitmaps/sticks.lbm img 4
@@ -1103,7 +1139,8 @@ bitmaps/sticks.lbm: bitmaps/sticks_4x1.xbm bitmaps/splash_9x.xbm bitmaps/splash_
 	$(IMG2LBM) bitmaps/logo_taranis.bmp bitmaps/logo_taranis.lbm bmp
 	$(IMG2LBM) bitmaps/icons.png bitmaps/icons.lbm bmp
 	$(IMG2LBM) bitmaps/asterisk.xbm bitmaps/asterisk.lbm img
-	$(IMG2LBM) bitmaps/about.png bitmaps/about.lbm bmp
+	$(IMG2LBM) bitmaps/about_taranis.png bitmaps/about_taranis.lbm bmp
+	$(IMG2LBM) bitmaps/about_9x.png bitmaps/about_9x.lbm img
 	$(IMG2LBM) bitmaps/asterisk_4bits.png bitmaps/asterisk_4bits.lbm bmp
 	 
 # Eye candy.
@@ -1215,7 +1252,7 @@ OBJS =  $(TMP:.s=.o)
 	@echo
 	@echo $(MSG_COMPILING) $@
 	$(CC) $(ARMCPPFLAGS) $< -o allsrc.o
-	$(CC) $(OBJS) allsrc.o -mcpu=cortex-m3 -mthumb -nostartfiles -T$(LDSCRIPT) -Wl,-Map=$(TARGET).map,--cref,--no-warn-mismatch -o $@
+	$(CC) $(OBJS) allsrc.o -mcpu=cortex-m3 -mthumb -nostartfiles -lm -T$(LDSCRIPT) -Wl,-Map=$(TARGET).map,--cref,--no-warn-mismatch -o $@
 endif
 
 # Target: clean project.

src/audio_arm.h

@@ -41,53 +41,87 @@
 
 #define AUDIO_FILENAME_MAXLEN (40)
 #define AUDIO_QUEUE_LENGTH    (20)
-#define BEEP_DEFAULT_FREQ     (140)
-#define BEEP_OFFSET           (10)
-#define BEEP_KEY_UP_FREQ      (BEEP_DEFAULT_FREQ+10)
-#define BEEP_KEY_DOWN_FREQ    (BEEP_DEFAULT_FREQ-10)
 
-extern uint16_t Sine_values[];
+#define AUDIO_SAMPLE_RATE     (32000)
+#define AUDIO_BUFFER_DURATION (10)
+#define AUDIO_BUFFER_SIZE     (AUDIO_SAMPLE_RATE*AUDIO_BUFFER_DURATION/1000)
+#define AUDIO_BUFFER_COUNT    (3)
 
-class ToneFragment {
-  public:
-    uint16_t freq;
-    uint8_t duration;
-    uint8_t pause;
-    uint8_t repeat;
-    int8_t  freqIncr;
-    uint8_t id;
+#define BEEP_MIN_FREQ         (440)
+#define BEEP_DEFAULT_FREQ     (2250)
+#define BEEP_KEY_UP_FREQ      (BEEP_DEFAULT_FREQ+150)
+#define BEEP_KEY_DOWN_FREQ    (BEEP_DEFAULT_FREQ-150)
+
+#define AUDIO_BUFFER_FREE     (0)
+#define AUDIO_BUFFER_FILLED   (1)
+#define AUDIO_BUFFER_PLAYING  (2)
+
+struct AudioBuffer {
+  uint16_t data[AUDIO_BUFFER_SIZE];
+  uint16_t size;
+  uint8_t  state;
 };
 
-class AudioFragment : public ToneFragment {
-  public:
+#define FRAGMENT_EMPTY     0
+#define FRAGMENT_TONE      1
+#define FRAGMENT_FILE      2
+
+struct AudioFragment {
+  uint8_t type;
+  uint8_t id;
+  uint8_t repeat;
+  union {
+    struct {
+      uint16_t freq;
+      uint16_t duration;
+      uint16_t pause;
+      int8_t   freqIncr;
+    } tone;
+
     char file[AUDIO_FILENAME_MAXLEN+1];
+  };
+
+  void clear()
+  {
+    memset(this, 0, sizeof(AudioFragment));
+  }
 };
 
-extern "C" void DAC_IRQHandler();
-
-#define AUDIO_NOT_STARTED  0
-#define AUDIO_SLEEPING     1
-#define AUDIO_RESUMING     2
-#define AUDIO_PLAYING_TONE 3
-#define AUDIO_PLAYING_WAV  4
-
-extern bool playingBackground;
-
 class AudioContext {
   public:
     AudioFragment fragment;
+
+    union {
 #if defined(SDCARD)
-    FIL wavFile;
+      struct {
+        FIL      file;
+        uint8_t  codec;
+        uint32_t freq;
+        uint32_t size;
+        uint8_t  resampleRatio;
+        uint16_t readSize;
+      } wav;
 #endif
-    uint8_t pcmCodec;
-    uint32_t pcmFreq;
-    uint32_t wavSize;
+
+      struct {
+        uint16_t points[100];
+        uint8_t  count;
+        uint8_t  idx;
+        uint16_t freq;
+      } tone;
+    } state;
+
+    inline void clear()
+    {
+      fragment.clear();
+    }
 };
 
+bool dacQueue(AudioBuffer *buffer);
+
 class AudioQueue {
 
   friend void audioTask(void* pdata);
-  friend void DAC_IRQHandler();
 
   public:
 
@@ -95,13 +129,13 @@ class AudioQueue {
 
     void start();
 
-    void play(uint16_t tFreq, uint8_t tLen, uint8_t tPause, uint8_t tFlags=0, int8_t tFreqIncr=0);
+    void play(uint16_t freq, uint16_t len, uint16_t pause=0, uint8_t flags=0, int8_t freqIncr=0);
 
     void playFile(const char *filename, uint8_t flags=0, uint8_t id=0);
 
     void stopPlay(uint8_t id);
 
-    void pause(uint8_t tLen);
+    void pause(uint16_t tLen);
 
     void stopSD();
 
@@ -109,16 +143,7 @@ class AudioQueue {
 
     bool started()
     {
-      return (state != AUDIO_NOT_STARTED);
-    }
-
-    bool busy()
-    {
-#ifdef SIMU
-      return false;
-#else
-      return (state != AUDIO_SLEEPING);
-#endif
+      return state;
     }
 
     bool empty()
@@ -128,27 +153,69 @@ class AudioQueue {
 
     void reset();
 
+    inline AudioBuffer * getNextFilledBuffer()
+    {
+      if (buffers[bufferRIdx].state == AUDIO_BUFFER_PLAYING) {
+        buffers[bufferRIdx].state = AUDIO_BUFFER_FREE;
+        bufferRIdx = nextBufferIdx(bufferRIdx);
+      }
+
+      uint8_t idx = bufferRIdx;
+      while (idx != bufferWIdx) {
+        AudioBuffer * buffer = &buffers[idx];
+        if (buffer->state == AUDIO_BUFFER_FILLED) {
+          buffer->state = AUDIO_BUFFER_PLAYING;
+          return buffer;
+        }
+        idx = nextBufferIdx(idx);
+      }
+
+      return NULL;
+    }
+
   protected:
 
     void wakeup();
 
-    void sdWakeup(AudioContext & context);
+    int mixAudioContext(AudioContext &context, AudioBuffer *buffer, int beepVolume, int wavVolume, unsigned int fade);
+    int mixBeep(AudioContext &context, AudioBuffer *buffer, int volume, unsigned int fade);
+    int mixWav(AudioContext &context, AudioBuffer *buffer, int volume, unsigned int fade);
 
-    volatile uint8_t state;
+    volatile bool state;
     uint8_t ridx;
     uint8_t widx;
-    int8_t prioIdx;
 
     AudioFragment fragments[AUDIO_QUEUE_LENGTH];
 
-    AudioContext currentContext;
     AudioContext backgroundContext; // for background music / vario
+    AudioContext currentContext;
+    AudioContext foregroundContext; // for important beeps
+
+    AudioBuffer buffers[AUDIO_BUFFER_COUNT];
+    uint8_t bufferRIdx;
+    uint8_t bufferWIdx;
+
+    inline uint8_t nextBufferIdx(uint8_t idx)
+    {
+      return (idx == AUDIO_BUFFER_COUNT-1 ? 0 : idx+1);
+    }
+
+    inline AudioBuffer * getEmptyBuffer()
+    {
+      AudioBuffer * buffer = &buffers[bufferWIdx];
+      if (buffer->state == AUDIO_BUFFER_FREE)
+        return buffer;
+      else
+        return NULL;
+    }
+
+    void pushBuffer(AudioBuffer *buffer);
 };
 
 extern AudioQueue audioQueue;
 
 void codecsInit();
-void audioEvent(uint8_t e, uint8_t f=BEEP_DEFAULT_FREQ);
+void audioEvent(uint8_t e, uint16_t f=BEEP_DEFAULT_FREQ);
 void audioStart();
 
 #if defined(AUDIO) && defined(BUZZER)
@@ -181,8 +248,7 @@ void audioStart();
 #define AUDIO_ERROR()            AUDIO_BUZZER(audioEvent(AU_ERROR), beep(4))
 #define AUDIO_TIMER_30()         AUDIO_BUZZER(audioEvent(AU_TIMER_30), { beepAgain=2; beep(2); })
 #define AUDIO_TIMER_20()         AUDIO_BUZZER(audioEvent(AU_TIMER_20), { beepAgain=1; beep(2); })
-#define AUDIO_TIMER_10()         AUDIO_BUZZER(audioEvent(AU_TIMER_10), beep(2))
-#define AUDIO_TIMER_LT3(x)       AUDIO_BUZZER(audioEvent(AU_TIMER_LT3), beep(2))
+#define AUDIO_TIMER_LT10(x)      AUDIO_BUZZER(audioEvent(AU_TIMER_LT10), beep(2))
 #define AUDIO_INACTIVITY()       AUDIO_BUZZER(audioEvent(AU_INACTIVITY), beep(3))
 #define AUDIO_MIX_WARNING(x)     AUDIO_BUZZER(audioEvent(AU_MIX_WARNING_1+x-1), beep(1))
 #define AUDIO_POT_STICK_MIDDLE() AUDIO_BUZZER(audioEvent(AU_POT_STICK_MIDDLE), beep(2))
@@ -204,6 +270,9 @@ void audioStart();
 #define AUDIO_SWR_RED()          audioEvent(AU_SWR_RED)
 #endif
 
+#define AUDIO_TELEMETRY_LOST()   audioEvent(AU_TELEMETRY_LOST)
+#define AUDIO_TELEMETRY_BACK()   audioEvent(AU_TELEMETRY_BACK)
+
 #define AUDIO_HEARTBEAT()
 
 #define SYSTEM_AUDIO_CATEGORY 0
@@ -241,8 +310,6 @@ extern void refreshModelAudioFiles();
 extern bool isAudioFileAvailable(uint32_t i, char * filename);
 
 // TODO not public, everything could be inside a function in audio_arm.cpp
-extern OS_TCID audioTimer;
-extern OS_FlagID audioFlag;
 extern OS_MutexID audioMutex;
 
 #endif

src/audio_avr.cpp

@@ -131,10 +131,9 @@ void audioQueue::play(uint8_t tFreq, uint8_t tLen, uint8_t tPause, uint8_t tFlag
     int8_t tFreqIncr = (tFlags >> 6);
     if (tFreqIncr == 3) tFreqIncr = -1;
 
-    if (tFreq > 0) { //we dont add pitch if zero as this is a pause only event
-      tFreq += g_eeGeneral.speakerPitch + BEEP_OFFSET; // add pitch compensator
-    }
+    tFreq += g_eeGeneral.speakerPitch + BEEP_OFFSET; // add pitch compensator
     tLen = getToneLength(tLen);
+
     if ((tFlags & PLAY_NOW) || (!busy() && empty())) {
       toneFreq = tFreq;
       toneTimeLeft = tLen;
@@ -167,7 +166,7 @@ void audioQueue::event(uint8_t e, uint8_t f)
   haptic.event(e); //do this before audio to help sync timings
 #endif
 
-  if (e <= AU_ERROR || e >= AU_WARNING1) {
+  if (e <= AU_ERROR || (e >= AU_WARNING1 && e < AU_FRSKY_FIRST)) {
     if (g_eeGeneral.alarmsFlash) {
       flashCounter = FLASH_DURATION;
     }
@@ -177,163 +176,94 @@ void audioQueue::event(uint8_t e, uint8_t f)
     if (e < AU_FRSKY_FIRST || empty()) {
       // TODO when VOICE enable some cases here are not needed!
       switch (e) {
-        // inactivity timer alert
-        case AU_INACTIVITY:
-          play(70, 10, 2, PLAY_REPEAT(2)|PLAY_NOW);
-          break;
-        // low battery in tx
+#if !defined(VOICE)
         case AU_TX_BATTERY_LOW:
           if (empty()) {
             play(60, 20, 3, PLAY_REPEAT(2)|PLAY_INCREMENT(1));
             play(80, 20, 3, PLAY_REPEAT(2)|PLAY_INCREMENT(-1));
           }
           break;
-        // error
-        case AU_ERROR:
-          play(BEEP_DEFAULT_FREQ, 40, 1, PLAY_NOW);
-          break;
-        // keypad up (seems to be used when going left/right through system menu options. 0-100 scales etc)
-        case AU_KEYPAD_UP:
-          play(BEEP_KEY_UP_FREQ, 10, 1, PLAY_NOW);
-          break;
-        // keypad down (seems to be used when going left/right through system menu options. 0-100 scales etc)
-        case AU_KEYPAD_DOWN:
-          play(BEEP_KEY_DOWN_FREQ, 10, 1, PLAY_NOW);
-          break;
-        // menu display (also used by a few generic beeps)
-        case AU_MENUS:
-          play(BEEP_DEFAULT_FREQ, 10, 2, PLAY_NOW);
-          break;
-        // trim move
+#endif
         case AU_TRIM_MOVE:
           play(f, 6, 1, PLAY_NOW);
           break;
-        // trim center
         case AU_TRIM_MIDDLE:
           play(f, 10, 2, PLAY_NOW);
           break;
-        // warning one
-        case AU_WARNING1:
-          play(BEEP_DEFAULT_FREQ, 10, 1, PLAY_NOW);
-          break;
-        // warning two
-        case AU_WARNING2:
-          play(BEEP_DEFAULT_FREQ, 20, 1, PLAY_NOW);
-          break;
-        // warning three
-        case AU_WARNING3:
-          play(BEEP_DEFAULT_FREQ, 30, 1, PLAY_NOW);
-          break;
-        // pot/stick center
-        case AU_POT_STICK_MIDDLE:
-          play(BEEP_DEFAULT_FREQ + 50, 10, 1, PLAY_NOW);
-          break;
-        // mix warning 1
-        case AU_MIX_WARNING_1:
-          play(BEEP_DEFAULT_FREQ + 50, 6, 0);
-          break;
-        // mix warning 2
-        case AU_MIX_WARNING_2:
-          play(BEEP_DEFAULT_FREQ + 52, 6, 3, PLAY_REPEAT(1));
-          break;
-        // mix warning 3
-        case AU_MIX_WARNING_3:
-          play(BEEP_DEFAULT_FREQ + 54, 6, 3, PLAY_REPEAT(2));
-          break;
-        // time 30 seconds left
-        case AU_TIMER_30:
-          play(BEEP_DEFAULT_FREQ + 50, 15, 3, PLAY_REPEAT(2)|PLAY_NOW);
-          break;
-        // time 20 seconds left
-        case AU_TIMER_20:
-          play(BEEP_DEFAULT_FREQ + 50, 15, 3, PLAY_REPEAT(1)|PLAY_NOW);
-          break;
-        // time 10 seconds left
-        case AU_TIMER_10:
-        // time <3 seconds left
-        case AU_TIMER_LT3:
-          play(BEEP_DEFAULT_FREQ + 50, 15, 3, PLAY_NOW);
-          break;
-        case AU_FRSKY_BEEP1:
-          play(BEEP_DEFAULT_FREQ, 10, 1);
-          pause(200);
-          break;
-        case AU_FRSKY_BEEP2:
-          play(BEEP_DEFAULT_FREQ, 20, 1);
-          pause(200);
-          break;
-        case AU_FRSKY_BEEP3:
-          play(BEEP_DEFAULT_FREQ, 30, 1);
-          pause(200);
-          break;
-        case AU_FRSKY_WARN1:
-          play(BEEP_DEFAULT_FREQ+20, 15, 5, PLAY_REPEAT(2));
-          pause(200);
-          break;
-        case AU_FRSKY_WARN2:
-          play(BEEP_DEFAULT_FREQ+30, 15, 5, PLAY_REPEAT(2));
-          pause(200);
-          break;
-        case AU_FRSKY_CHEEP:
-          play(BEEP_DEFAULT_FREQ+30, 10, 2, PLAY_REPEAT(2)|PLAY_INCREMENT(2));
-          pause(200);
-          break;
         case AU_FRSKY_RING:
           play(BEEP_DEFAULT_FREQ+25, 5, 2, PLAY_REPEAT(10));
           play(BEEP_DEFAULT_FREQ+25, 5, 10, PLAY_REPEAT(1));
           play(BEEP_DEFAULT_FREQ+25, 5, 2, PLAY_REPEAT(10));
-          pause(200);
           break;
         case AU_FRSKY_SCIFI:
           play(80, 10, 3, PLAY_REPEAT(2)|PLAY_INCREMENT(-1));
           play(60, 10, 3, PLAY_REPEAT(2)|PLAY_INCREMENT(1));
           play(70, 10, 1);
-          pause(200);
           break;
         case AU_FRSKY_ROBOT:
           play(70, 5, 1, PLAY_REPEAT(1));
           play(50, 15, 2, PLAY_REPEAT(1));
           play(80, 15, 2, PLAY_REPEAT(1));
-          pause(200);
           break;
         case AU_FRSKY_CHIRP:
           play(BEEP_DEFAULT_FREQ+40, 5, 1, PLAY_REPEAT(2));
           play(BEEP_DEFAULT_FREQ+54, 5, 1, PLAY_REPEAT(3));
-          pause(200);
           break;
         case AU_FRSKY_TADA:
           play(50, 5, 5);
           play(90, 5, 5);
           play(110, 3, 4, PLAY_REPEAT(2));
-          pause(200);
           break;
         case AU_FRSKY_CRICKET:
           play(80, 5, 10, PLAY_REPEAT(3));
           play(80, 5, 20, PLAY_REPEAT(1));
           play(80, 5, 10, PLAY_REPEAT(3));
-          pause(200);
-          break;
-        case AU_FRSKY_SIREN:
-          play(10, 20, 5, PLAY_REPEAT(2)|PLAY_INCREMENT(1));
-          pause(200);
           break;
         case AU_FRSKY_ALARMC:
           play(50, 4, 10, PLAY_REPEAT(2));
           play(70, 8, 20, PLAY_REPEAT(1));
           play(50, 8, 10, PLAY_REPEAT(2));
           play(70, 4, 20, PLAY_REPEAT(1));
-          pause(200);
-          break;
-        case AU_FRSKY_RATATA:
-          play(BEEP_DEFAULT_FREQ+50, 5, 10, PLAY_REPEAT(10));
-          pause(200);
-          break;
-        case AU_FRSKY_TICK:
-          play(BEEP_DEFAULT_FREQ+50, 5, 50, PLAY_REPEAT(2));
-          pause(200);
           break;
         default:
+        {
+          const static pm_uint8_t singleSounds[] PROGMEM = {
+              70, 10, 2, PLAY_REPEAT(2)|PLAY_NOW,  // INACTIVITY
+              BEEP_DEFAULT_FREQ, 40, 1, PLAY_NOW,  // ERROR
+              BEEP_KEY_UP_FREQ, 10, 1, PLAY_NOW,   // KEYPAD_UP
+              BEEP_KEY_DOWN_FREQ, 10, 1, PLAY_NOW, // KEYPAD_DOWN
+              BEEP_DEFAULT_FREQ, 10, 2, PLAY_NOW,  // MENUS
+              0,0,0,0, // TRIM_MOVE
+              BEEP_DEFAULT_FREQ, 10, 1, PLAY_NOW,  // WARNING1
+              BEEP_DEFAULT_FREQ, 20, 1, PLAY_NOW,  // WARNING2
+              BEEP_DEFAULT_FREQ, 30, 1, PLAY_NOW,  // WARNING3
+              0,0,0,0, // TRIM_MIDDLE
+              BEEP_DEFAULT_FREQ + 50, 10, 1, PLAY_NOW,      // POT_STICK_MIDDLE
+              BEEP_DEFAULT_FREQ + 50, 6, 0, 0,              // MIX_WARNING_1
+              BEEP_DEFAULT_FREQ + 52, 6, 3, PLAY_REPEAT(1), // MIX_WARNING_2
+              BEEP_DEFAULT_FREQ + 54, 6, 3, PLAY_REPEAT(2), // MIX_WARNING_3
+              BEEP_DEFAULT_FREQ + 50, 15, 3, PLAY_NOW, // TIMER_LT10
+              BEEP_DEFAULT_FREQ + 50, 15, 3, PLAY_REPEAT(1)|PLAY_NOW, // TIMER_20
+              BEEP_DEFAULT_FREQ + 50, 15, 3, PLAY_REPEAT(2)|PLAY_NOW, // TIMER_30
+              BEEP_DEFAULT_FREQ, 10, 1, 0, // FRSKY_BEEP1
+              BEEP_DEFAULT_FREQ, 20, 1, 0, // FRSKY_BEEP2
+              BEEP_DEFAULT_FREQ, 30, 1, 0, // FRSKY_BEEP3
+              BEEP_DEFAULT_FREQ+20, 15, 5, PLAY_REPEAT(2), // FRSKY_WARN1
+              BEEP_DEFAULT_FREQ+30, 15, 5, PLAY_REPEAT(2), // FRSKY_WARN2
+              BEEP_DEFAULT_FREQ+30, 10, 2, PLAY_REPEAT(2)|PLAY_INCREMENT(2), // FRSKY_CHEEP
+              BEEP_DEFAULT_FREQ+50, 5, 10, PLAY_REPEAT(10), // FRSKY_RATATA
+              BEEP_DEFAULT_FREQ+50, 5, 50, PLAY_REPEAT(2), // FRSKY_TICK
+              10, 20, 5, PLAY_REPEAT(2)|PLAY_INCREMENT(1), // FRSKY_SIREN
+          };
+
+          const pm_uint8_t *ptr = &singleSounds[(e-AU_INACTIVITY)<<2];
+          uint8_t tFreq = pgm_read_byte(ptr++);
+          uint8_t tLen = pgm_read_byte(ptr++);
+          uint8_t tPause = pgm_read_byte(ptr++);
+          uint8_t tFlags = pgm_read_byte(ptr);
+          play(tFreq, tLen, tPause, tFlags);
           break;
+        }
       }
     }
   }

src/audio_avr.h

@@ -136,10 +136,9 @@ void audioDefevent(uint8_t e);
 #define AUDIO_INACTIVITY()       VOICE_AUDIO_BUZZER(PUSH_SYSTEM_PROMPT(AU_INACTIVITY), audioDefevent(AU_INACTIVITY), beep(3))
 #define AUDIO_ERROR_MESSAGE(e)   VOICE_AUDIO_BUZZER(PUSH_SYSTEM_PROMPT((e)), audioDefevent(AU_ERROR), beep(4))
 #define AUDIO_TIMER_MINUTE(t)    VOICE_AUDIO_BUZZER(playDuration(t), audioDefevent(AU_WARNING1), beep(2))
-#define AUDIO_TIMER_30()         VOICE_AUDIO_BUZZER(PUSH_SYSTEM_PROMPT(AU_TIMER_30), audioDefevent(AU_TIMER_30), { beepAgain=2; beep(2); })
-#define AUDIO_TIMER_20()         VOICE_AUDIO_BUZZER(PUSH_SYSTEM_PROMPT(AU_TIMER_20), audioDefevent(AU_TIMER_20), { beepAgain=1; beep(2); })
-#define AUDIO_TIMER_10()         VOICE_AUDIO_BUZZER(PUSH_SYSTEM_PROMPT(AU_TIMER_10), audioDefevent(AU_TIMER_10), beep(2))
-#define AUDIO_TIMER_LT3(x)       VOICE_AUDIO_BUZZER(PUSH_SYSTEM_PROMPT(AU_TIMER_LT3), audioDefevent(AU_TIMER_LT3), beep(2))
+#define AUDIO_TIMER_30()         VOICE_AUDIO_BUZZER(PUSH_SYSTEM_PROMPT(AU_TIMER_30+1/*to avoid renumbering*/), audioDefevent(AU_TIMER_30), { beepAgain=2; beep(2); })
+#define AUDIO_TIMER_20()         VOICE_AUDIO_BUZZER(PUSH_SYSTEM_PROMPT(AU_TIMER_20+1/*to avoid renumbering*/), audioDefevent(AU_TIMER_20), { beepAgain=1; beep(2); })
+#define AUDIO_TIMER_LT10(x)      AUDIO_BUZZER(audioDefevent(AU_TIMER_LT10), beep(2))
 #define AUDIO_MIX_WARNING(x)     AUDIO_BUZZER(audioDefevent(AU_MIX_WARNING_1+x-1), beep(1))
 #define AUDIO_POT_STICK_MIDDLE() AUDIO_BUZZER(audioDefevent(AU_POT_STICK_MIDDLE), beep(2))
 #define AUDIO_VARIO_UP()         audioDefevent(AU_KEYPAD_UP)

src/bitmaps/about_9x.lbm

@@ -0,0 +1,4 @@
+11,17,
+0x00,0x80,0x80,0xbe,0xe3,0xc1,0xc1,0xc1,0xe3,0xff,0xff,
+0x00,0xe7,0x24,0x3c,0x00,0x00,0x00,0x00,0x3f,0x3f,0xff,
+0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,

src/bitmaps/font.xbm

@@ -1,43 +0,0 @@
-#define font_width 80
-#define font_height 48
-static unsigned char font_bits[] = {
-   0x00, 0x29, 0xe0, 0x86, 0x31, 0x48, 0x00, 0x00, 0x00, 0x00, 0x00, 0x29,
-   0xe8, 0x66, 0x22, 0x84, 0x10, 0x02, 0x00, 0x80, 0x00, 0x29, 0xec, 0x50,
-   0x11, 0x02, 0x55, 0x02, 0x00, 0x40, 0x00, 0x81, 0xf6, 0x89, 0x00, 0x02,
-   0xb9, 0x0f, 0x3c, 0x20, 0x00, 0x80, 0xe3, 0x44, 0x05, 0x02, 0x55, 0x62,
-   0x00, 0x10, 0x00, 0x01, 0xe1, 0x72, 0x02, 0x84, 0x10, 0x42, 0x80, 0x09,
-   0x00, 0x01, 0xe0, 0xb0, 0x05, 0x48, 0x00, 0x20, 0x80, 0x01, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0c, 0x31, 0x07, 0x3d,
-   0xf3, 0x8c, 0x01, 0x00, 0x41, 0x70, 0x92, 0x49, 0x88, 0x85, 0x84, 0x52,
-   0x32, 0x86, 0x80, 0x88, 0x12, 0x41, 0x48, 0x9d, 0x40, 0x52, 0x32, 0x46,
-   0x3e, 0x81, 0x12, 0x21, 0x26, 0xa1, 0x23, 0x8c, 0x03, 0x20, 0x00, 0x42,
-   0x12, 0x11, 0xe8, 0xa1, 0x24, 0x12, 0x32, 0x46, 0x3e, 0x21, 0x12, 0x09,
-   0x08, 0xa5, 0x24, 0x12, 0x31, 0x84, 0x80, 0x00, 0x8c, 0x7b, 0x07, 0x19,
-   0x23, 0x8c, 0x00, 0x02, 0x41, 0x20, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0xc6, 0x3d, 0x77, 0xfe, 0x77, 0xd1, 0xf1, 0x18,
-   0x62, 0x74, 0x29, 0xc6, 0x98, 0x42, 0x88, 0x91, 0xa0, 0x14, 0x76, 0x8c,
-   0x29, 0xc6, 0x10, 0x43, 0x08, 0x91, 0xa0, 0x12, 0xea, 0x8c, 0xe6, 0xbf,
-   0x10, 0xdf, 0xeb, 0x9f, 0xa0, 0x11, 0x6a, 0x8d, 0x20, 0xc6, 0x10, 0x43,
-   0x88, 0x91, 0xa0, 0x12, 0x62, 0x8e, 0x20, 0xc6, 0x98, 0x42, 0x88, 0x91,
-   0xa4, 0x14, 0x62, 0x8c, 0x20, 0x3e, 0x77, 0x7e, 0xf0, 0xd1, 0x99, 0xf8,
-   0x63, 0x74, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0xcf, 0x3d, 0xf7, 0x63, 0x8c, 0x31, 0x7e, 0x07, 0x1c, 0x01, 0x31, 0xc6,
-   0x48, 0x62, 0x8c, 0x31, 0x42, 0x11, 0x90, 0x02, 0x31, 0xc6, 0x40, 0x62,
-   0x8c, 0x2a, 0x22, 0x21, 0x50, 0x04, 0x2f, 0x3e, 0x47, 0x62, 0x8c, 0x44,
-   0x11, 0x41, 0x10, 0x00, 0xa1, 0x16, 0x48, 0x62, 0xac, 0x8a, 0x08, 0x81,
-   0x10, 0x00, 0x21, 0xa5, 0x48, 0xa2, 0xaa, 0x91, 0x04, 0x01, 0x11, 0x00,
-   0xc1, 0x46, 0x47, 0x1c, 0x51, 0x91, 0x7c, 0x07, 0x1c, 0xf8, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x02, 0x04, 0x00, 0x01,
-   0x03, 0x81, 0xa0, 0x60, 0x00, 0x00, 0x04, 0x04, 0x00, 0x81, 0xf4, 0x01,
-   0x80, 0x40, 0x00, 0x00, 0xc8, 0x35, 0x67, 0x9d, 0x88, 0xcd, 0xb0, 0x44,
-   0x56, 0x73, 0x00, 0xce, 0x90, 0xe3, 0x89, 0x93, 0xa0, 0x42, 0xea, 0x8c,
-   0xc0, 0xc7, 0x10, 0xbf, 0xf0, 0x91, 0xa0, 0x41, 0x6a, 0x8c, 0x20, 0xc6,
-   0x18, 0x83, 0x80, 0x91, 0xa4, 0x42, 0x62, 0x8c, 0xc0, 0x3f, 0xe7, 0x9d,
-   0x70, 0xd1, 0x99, 0xe4, 0x62, 0x74, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x20, 0x00, 0x00, 0x00, 0x00, 0x10,
-   0x02, 0x00, 0x00, 0x00, 0x20, 0x00, 0x00, 0x00, 0x00, 0x10, 0x04, 0x21,
-   0xcf, 0x36, 0x77, 0x62, 0x8c, 0x31, 0x7e, 0x10, 0x08, 0x12, 0x31, 0xcf,
-   0x20, 0x62, 0x8c, 0x2a, 0x22, 0x15, 0xd0, 0xde, 0xcf, 0x07, 0x27, 0x62,
-   0x8c, 0xc4, 0x93, 0x12, 0x08, 0x12, 0x01, 0x06, 0x28, 0xb3, 0xaa, 0x0a,
-   0x0a, 0x10, 0x14, 0x21, 0x01, 0x86, 0xc7, 0x2c, 0x51, 0xd1, 0x7d, 0x10,
-   0x0a, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };

src/bitmaps/font_dblsize.xbm

@@ -1,163 +0,0 @@
-#define font_dblsize_width 160
-#define font_dblsize_height 96
-static unsigned char font_dblsize_bits[] = {
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xc0, 0xc0, 0x0c,
-   0x33, 0x30, 0x18, 0xc0, 0x03, 0x0f, 0xc0, 0x30, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0xc0, 0xc0, 0x0c, 0x33, 0x30, 0x3c, 0xe0,
-   0x07, 0x0f, 0xe0, 0x70, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0xc0, 0xc0, 0x0c, 0x33, 0xfc, 0x3f, 0x7c, 0x0c, 0x0c, 0x70, 0xe0,
-   0x00, 0x03, 0x0c, 0x00, 0x00, 0x00, 0x00, 0xc0, 0x00, 0xc0, 0xc0, 0x0c,
-   0x33, 0xfe, 0x1b, 0x3e, 0x0e, 0x0e, 0x38, 0xc0, 0x01, 0x03, 0x0c, 0x00,
-   0x00, 0x00, 0x00, 0xe0, 0x00, 0xc0, 0xc0, 0xcc, 0xff, 0x33, 0x00, 0x37,
-   0x07, 0x07, 0x1c, 0x80, 0x33, 0x33, 0x0c, 0x00, 0x00, 0x00, 0x00, 0x70,
-   0x00, 0xc0, 0x80, 0xc4, 0xff, 0x33, 0x80, 0xb3, 0x03, 0x03, 0x0c, 0x00,
-   0x73, 0x3b, 0x0c, 0x00, 0x00, 0x00, 0x00, 0x38, 0x00, 0xc0, 0x00, 0x00,
-   0x33, 0xfe, 0xc0, 0xe1, 0x01, 0x00, 0x0c, 0x00, 0xc3, 0xcf, 0xff, 0x00,
-   0xf0, 0x0f, 0x00, 0x1c, 0x00, 0xc0, 0x00, 0x00, 0x33, 0xfc, 0xe1, 0xe0,
-   0x01, 0x00, 0x0c, 0x00, 0xc3, 0xcf, 0xff, 0x00, 0xf0, 0x0f, 0x00, 0x0e,
-   0x00, 0x00, 0x00, 0xc0, 0xff, 0x30, 0x73, 0xb0, 0x33, 0x00, 0x0c, 0x00,
-   0x73, 0x3b, 0x0c, 0x3c, 0x00, 0x00, 0x00, 0x07, 0x00, 0x00, 0x00, 0xc0,
-   0xff, 0x30, 0x3b, 0x30, 0x3f, 0x00, 0x1c, 0x80, 0x33, 0x33, 0x0c, 0x3c,
-   0x00, 0x00, 0x80, 0x03, 0x00, 0x00, 0x00, 0x00, 0x33, 0xff, 0x1d, 0x36,
-   0x0c, 0x00, 0x38, 0xc0, 0x01, 0x03, 0x0c, 0x30, 0x00, 0x80, 0xc1, 0x01,
-   0x00, 0xc0, 0x00, 0x00, 0x33, 0xff, 0x0c, 0x7f, 0x0c, 0x00, 0x70, 0xe0,
-   0x00, 0x03, 0x0c, 0x38, 0x00, 0xc0, 0xc3, 0x00, 0x00, 0xc0, 0x00, 0x00,
-   0x33, 0x30, 0x00, 0xef, 0x3f, 0x00, 0xe0, 0x70, 0x00, 0x00, 0x00, 0x1c,
-   0x00, 0xc0, 0x03, 0x00, 0x00, 0xc0, 0x00, 0x00, 0x33, 0x30, 0x00, 0xc6,
-   0x33, 0x00, 0xc0, 0x30, 0x00, 0x00, 0x00, 0x0c, 0x00, 0x80, 0x01, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0xf0, 0xc0, 0x00, 0x0f, 0x3f, 0x00, 0xf3, 0x0f,
-   0x0f, 0xff, 0xf0, 0xc0, 0x03, 0x00, 0x00, 0x00, 0x03, 0x30, 0x00, 0x3f,
-   0xf8, 0xe1, 0x80, 0x1f, 0x7f, 0x80, 0xf3, 0x8f, 0x1f, 0xff, 0xf8, 0xe1,
-   0x07, 0x00, 0x00, 0x80, 0x03, 0x70, 0x80, 0x7f, 0x9c, 0xf3, 0xc0, 0x39,
-   0xe0, 0xc0, 0x33, 0xc0, 0x39, 0xc0, 0x9c, 0x73, 0x8e, 0x01, 0x06, 0xc0,
-   0x01, 0xe0, 0xc0, 0xe1, 0x0c, 0xf3, 0xc0, 0x30, 0xc0, 0xe0, 0x33, 0xc0,
-   0x30, 0xe0, 0x0c, 0x33, 0xcc, 0x03, 0x0f, 0xe0, 0x00, 0xc0, 0xc1, 0xc0,
-   0x0c, 0xc3, 0x00, 0x30, 0xc0, 0x70, 0xf3, 0xc3, 0x00, 0x70, 0x0c, 0x33,
-   0xcc, 0x03, 0x0f, 0x70, 0xfc, 0x8f, 0x03, 0xc0, 0x0c, 0xc3, 0x00, 0x38,
-   0xe0, 0x38, 0xf3, 0xc7, 0x00, 0x38, 0x9c, 0x73, 0x8e, 0x01, 0x06, 0x38,
-   0xfc, 0x0f, 0x07, 0xe0, 0x0c, 0xc3, 0x00, 0x1c, 0x7c, 0x1c, 0x03, 0xce,
-   0x0f, 0x1c, 0xf8, 0xe1, 0x0f, 0x00, 0x00, 0x1c, 0x00, 0x00, 0x0e, 0x70,
-   0x0c, 0xc3, 0x00, 0x0e, 0x7c, 0x0c, 0x03, 0xcc, 0x1f, 0x0c, 0xf8, 0xc1,
-   0x0f, 0x00, 0x00, 0x1c, 0x00, 0x00, 0x0e, 0x38, 0x0c, 0xc3, 0x00, 0x07,
-   0xe0, 0xfc, 0x03, 0xcc, 0x38, 0x0c, 0x9c, 0x03, 0x8c, 0x01, 0x0f, 0x38,
-   0xfc, 0x0f, 0x07, 0x1c, 0x0c, 0xc3, 0x80, 0x03, 0xc0, 0xfc, 0x03, 0xcc,
-   0x30, 0x0c, 0x0c, 0x03, 0xce, 0x03, 0x0f, 0x70, 0xfc, 0x8f, 0x03, 0x0c,
-   0x0c, 0xc3, 0xc0, 0x01, 0xc0, 0x00, 0x33, 0xcc, 0x30, 0x0c, 0x0c, 0x03,
-   0xc7, 0x03, 0x0c, 0xe0, 0x00, 0xc0, 0x01, 0x00, 0x9c, 0xc3, 0xc0, 0x00,
-   0xe0, 0x00, 0x73, 0xce, 0x39, 0x0c, 0x9c, 0x83, 0x83, 0x01, 0x0e, 0xc0,
-   0x01, 0xe0, 0x00, 0x00, 0xf8, 0xf1, 0xc3, 0x3f, 0x7f, 0x00, 0xe3, 0x87,
-   0x1f, 0x0c, 0xf8, 0xc1, 0x01, 0x00, 0x07, 0x80, 0x03, 0x70, 0x00, 0x0c,
-   0xf0, 0xf0, 0xc3, 0x3f, 0x3f, 0x00, 0xc3, 0x03, 0x0f, 0x0c, 0xf0, 0xc0,
-   0x00, 0x00, 0x03, 0x00, 0x03, 0x30, 0x00, 0x0c, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x3c, 0xc0, 0xf0, 0x0f, 0x3f, 0x3f, 0xfc, 0xff, 0x3f, 0x3f, 0x03, 0xf3,
-   0x03, 0xff, 0xc0, 0x03, 0x0c, 0x3c, 0x30, 0x3f, 0x7e, 0xe0, 0xf1, 0x9f,
-   0x7f, 0x7f, 0xfc, 0xff, 0xbf, 0x7f, 0x03, 0xf3, 0x03, 0xff, 0xe0, 0x03,
-   0x1c, 0x3e, 0xb0, 0x7f, 0xe7, 0xf0, 0x33, 0xf8, 0xe1, 0xe3, 0x0c, 0x30,
-   0xc0, 0xe1, 0x03, 0xc3, 0x00, 0xcc, 0x70, 0x03, 0x3c, 0x3f, 0xf0, 0xe1,
-   0xc3, 0x38, 0x37, 0xf0, 0xc0, 0xc3, 0x0d, 0x30, 0xc0, 0xc0, 0x03, 0xc3,
-   0x00, 0xcc, 0x38, 0x03, 0xfc, 0x7f, 0xf0, 0xc0, 0xc3, 0x1c, 0x3e, 0xf0,
-   0x00, 0x83, 0x0f, 0x30, 0xc0, 0x00, 0x03, 0xc3, 0x00, 0xcc, 0x1c, 0x03,
-   0xec, 0xfd, 0xf0, 0xc0, 0xe7, 0x0c, 0x3c, 0xf8, 0x00, 0x03, 0x0f, 0x30,
-   0xc0, 0x00, 0x03, 0xc3, 0x00, 0xcc, 0x0e, 0x03, 0xcc, 0xfc, 0xf1, 0xc0,
-   0x7e, 0xfc, 0xff, 0xdf, 0x00, 0x03, 0xff, 0xf3, 0xcf, 0xfc, 0xff, 0xc3,
-   0x00, 0xcc, 0x07, 0x03, 0xcc, 0xbc, 0xf3, 0xc0, 0x3c, 0xfc, 0xff, 0xdf,
-   0x00, 0x03, 0xff, 0xf3, 0xcf, 0xfc, 0xff, 0xc3, 0x00, 0xcc, 0x07, 0x03,
-   0xcc, 0x3c, 0xf7, 0xc0, 0x00, 0x0c, 0x3c, 0xf8, 0x00, 0x03, 0x0f, 0x30,
-   0xc0, 0xc0, 0x03, 0xc3, 0x00, 0xcc, 0x0e, 0x03, 0x0c, 0x3c, 0xfe, 0xc0,
-   0x00, 0x0c, 0x3c, 0xf0, 0x00, 0x83, 0x0f, 0x30, 0xc0, 0xc0, 0x03, 0xc3,
-   0x00, 0xcc, 0x1c, 0x03, 0x0c, 0x3c, 0xfc, 0xc0, 0x00, 0x0c, 0x3c, 0xf0,
-   0xc0, 0xc3, 0x0d, 0x30, 0xc0, 0xc0, 0x03, 0xc3, 0x30, 0xcc, 0x38, 0x03,
-   0x0c, 0x3c, 0xf8, 0xc0, 0x00, 0x0c, 0x3c, 0xf8, 0xe1, 0xe3, 0x0c, 0x30,
-   0xc0, 0xe1, 0x03, 0xc3, 0x70, 0xce, 0x70, 0x03, 0x0c, 0x3c, 0xf0, 0xe1,
-   0x00, 0x0c, 0xfc, 0x9f, 0x7f, 0x7f, 0xfc, 0x3f, 0x80, 0xff, 0x03, 0xf3,
-   0xe3, 0xc7, 0xe0, 0xff, 0x0f, 0x3c, 0xb0, 0x7f, 0x00, 0x0c, 0xfc, 0x0f,
-   0x3f, 0x3f, 0xfc, 0x3f, 0x00, 0x7f, 0x03, 0xf3, 0xc3, 0xc3, 0xc0, 0xff,
-   0x0f, 0x3c, 0x30, 0x3f, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xff, 0xf0, 0xf3, 0x0f,
-   0x3f, 0xff, 0x0f, 0x3c, 0xf0, 0xc0, 0x03, 0x0f, 0xfc, 0x3f, 0x3f, 0x00,
-   0xf0, 0x03, 0x03, 0x00, 0xff, 0xf9, 0xf7, 0x9f, 0x7f, 0xff, 0x0f, 0x3c,
-   0xf0, 0xc0, 0x03, 0x0f, 0xfc, 0x3f, 0x3f, 0x00, 0xf0, 0x83, 0x07, 0x00,
-   0x83, 0x1f, 0x3e, 0xf8, 0xe1, 0x30, 0x0c, 0x3c, 0xf0, 0xc0, 0x03, 0x0f,
-   0x0c, 0x30, 0x03, 0x03, 0x00, 0xc3, 0x0f, 0x00, 0x03, 0x0f, 0x3c, 0xf0,
-   0xc0, 0x30, 0x0c, 0x3c, 0xf0, 0xc0, 0x87, 0x0f, 0x0c, 0x38, 0x03, 0x07,
-   0x00, 0xe3, 0x1c, 0x00, 0x03, 0x0f, 0x3c, 0xf0, 0x00, 0x30, 0x0c, 0x3c,
-   0xf0, 0xc0, 0xce, 0x0d, 0x0c, 0x1c, 0x03, 0x0e, 0x00, 0x73, 0x38, 0x00,
-   0x83, 0x0f, 0x3c, 0xf8, 0x01, 0x30, 0x0c, 0x3c, 0xf0, 0xc0, 0xfc, 0x1c,
-   0x0e, 0x0e, 0x03, 0x1c, 0x00, 0x33, 0x30, 0x00, 0xff, 0x0d, 0xfc, 0x9f,
-   0x3f, 0x30, 0x0c, 0x3c, 0xf0, 0xc0, 0x78, 0x38, 0x07, 0x07, 0x03, 0x38,
-   0x00, 0x03, 0x00, 0x00, 0xff, 0x0c, 0xfc, 0x0f, 0x7f, 0x30, 0x0c, 0x3c,
-   0xf0, 0xc0, 0x78, 0xf0, 0x83, 0x03, 0x03, 0x70, 0x00, 0x03, 0x00, 0x00,
-   0x03, 0xcc, 0x3c, 0x03, 0xe0, 0x30, 0x0c, 0x3c, 0xf0, 0xcc, 0xfc, 0xe0,
-   0xc1, 0x01, 0x03, 0xe0, 0x00, 0x03, 0x00, 0x00, 0x03, 0xcc, 0x3d, 0x07,
-   0xc0, 0x30, 0x0c, 0x7c, 0xf8, 0xcc, 0xce, 0xc1, 0xe0, 0x00, 0x03, 0xc0,
-   0x01, 0x03, 0x00, 0x00, 0x03, 0x8c, 0x37, 0xce, 0xc0, 0x30, 0x0c, 0xec,
-   0xdc, 0xcc, 0x87, 0xc3, 0x70, 0x00, 0x03, 0x80, 0x03, 0x03, 0x00, 0x00,
-   0x03, 0x1c, 0x37, 0xdc, 0xe1, 0x30, 0x1c, 0xce, 0xcf, 0xff, 0x03, 0xc3,
-   0x30, 0x00, 0x03, 0x00, 0x03, 0x03, 0x00, 0x00, 0x03, 0xf8, 0x3f, 0xb8,
-   0x7f, 0x30, 0xf8, 0x87, 0x87, 0x7f, 0x03, 0xc3, 0xf0, 0x3f, 0x3f, 0x00,
-   0xf0, 0x03, 0xc0, 0xff, 0x03, 0xf0, 0x3c, 0x30, 0x3f, 0x30, 0xf0, 0x03,
-   0x03, 0x33, 0x03, 0xc3, 0xf0, 0x3f, 0x3f, 0x00, 0xf0, 0x03, 0xc0, 0xff,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x0c, 0x00, 0x30, 0x00, 0x00, 0x00, 0x03, 0x00,
-   0x0f, 0x00, 0x03, 0xc0, 0x00, 0xcc, 0x00, 0x3c, 0x00, 0x00, 0x00, 0x00,
-   0x1c, 0x00, 0x30, 0x00, 0x00, 0x00, 0x03, 0x80, 0x1f, 0x00, 0x03, 0xc0,
-   0x00, 0xcc, 0x00, 0x3c, 0x00, 0x00, 0x00, 0x00, 0x38, 0x00, 0x30, 0x00,
-   0x00, 0x00, 0x03, 0xc0, 0x39, 0xff, 0x03, 0x00, 0x00, 0xc0, 0x00, 0x30,
-   0x00, 0x00, 0x00, 0x00, 0x70, 0x00, 0x30, 0x00, 0x00, 0x00, 0x03, 0xc0,
-   0xb0, 0xff, 0x03, 0x00, 0x00, 0xc0, 0x00, 0x30, 0x00, 0x00, 0x00, 0x00,
-   0xe0, 0xf0, 0x33, 0x0f, 0x3f, 0x3c, 0xf3, 0xc3, 0xc0, 0xc1, 0xf3, 0xf0,
-   0x00, 0xcf, 0x30, 0x30, 0x3c, 0x33, 0x0f, 0x3f, 0xc0, 0xf0, 0xb7, 0x9f,
-   0x3f, 0x7e, 0xfb, 0xc7, 0xc0, 0xc0, 0xfb, 0xf1, 0x00, 0xcf, 0x38, 0x30,
-   0xfc, 0xb7, 0x9f, 0x7f, 0x00, 0x00, 0xfe, 0xf9, 0x01, 0xe7, 0x1f, 0xfe,
-   0xc3, 0xc0, 0x9f, 0xc3, 0x00, 0xcc, 0x1c, 0x30, 0xec, 0xff, 0xf9, 0xe1,
-   0x00, 0x00, 0xfc, 0xf0, 0x00, 0xc3, 0x0f, 0xfc, 0xc3, 0xc1, 0x0f, 0xc3,
-   0x00, 0xcc, 0x0e, 0x30, 0xcc, 0xfc, 0xf0, 0xc0, 0x00, 0xf0, 0x3f, 0xf0,
-   0x00, 0x03, 0xff, 0xcf, 0x80, 0xff, 0x03, 0xc3, 0x00, 0xcc, 0x07, 0x30,
-   0xcc, 0x3c, 0xf0, 0xc0, 0x00, 0xf8, 0x3f, 0xf0, 0x00, 0x03, 0xff, 0xcf,
-   0x00, 0xff, 0x03, 0xc3, 0x00, 0xcc, 0x07, 0x30, 0xcc, 0x3c, 0xf0, 0xc0,
-   0x00, 0x1c, 0x3c, 0xf0, 0xc0, 0x03, 0x0f, 0xc0, 0x00, 0xc0, 0x03, 0xc3,
-   0x30, 0xcc, 0x0e, 0x30, 0x0c, 0x3c, 0xf0, 0xc0, 0x00, 0x1c, 0x3c, 0xf8,
-   0xe1, 0x07, 0x1f, 0xc0, 0x00, 0xe0, 0x03, 0xc3, 0x70, 0xce, 0x1c, 0x30,
-   0x0c, 0x3c, 0xf0, 0xe1, 0x00, 0xf8, 0xff, 0x9f, 0x7f, 0xfe, 0xfb, 0xc3,
-   0x00, 0x7f, 0x03, 0xf3, 0xe3, 0xc7, 0x38, 0xfc, 0x0c, 0x3c, 0xb0, 0x7f,
-   0x00, 0xf0, 0xff, 0x0f, 0x3f, 0xfc, 0xf3, 0xc3, 0x00, 0x3f, 0x03, 0xf3,
-   0xc3, 0xc3, 0x30, 0xfc, 0x0c, 0x3c, 0x30, 0x3f, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x0c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x30, 0x30, 0x30, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x0c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x38, 0x30,
-   0x70, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0c, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x1c, 0x30, 0xe0, 0x00, 0x03, 0x0c,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x0c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x0c, 0x30, 0xc0, 0x00, 0x07, 0x0e, 0xff, 0xf0, 0x3c, 0x0f,
-   0x3f, 0x3f, 0x0c, 0x3c, 0xf0, 0xc0, 0x03, 0x0f, 0xfc, 0x3f, 0x0c, 0x30,
-   0xc0, 0x00, 0x0e, 0x07, 0xff, 0xf9, 0xbd, 0x9f, 0x3f, 0x3f, 0x0c, 0x3c,
-   0xf0, 0xc0, 0x87, 0x0f, 0xfc, 0x3f, 0x0e, 0x30, 0xc0, 0x01, 0x9c, 0x03,
-   0x83, 0x1f, 0xff, 0xf9, 0x01, 0x0c, 0x0c, 0x3c, 0xf0, 0xc0, 0xce, 0x0d,
-   0x0c, 0x1c, 0x03, 0x30, 0x00, 0xf3, 0xfc, 0xf3, 0x83, 0x1f, 0xff, 0xf0,
-   0x01, 0x0c, 0x0c, 0x3c, 0xf0, 0xc0, 0xfc, 0x1c, 0x0c, 0x0e, 0x03, 0x30,
-   0x00, 0xf3, 0xfc, 0xf3, 0xff, 0xf9, 0x3f, 0x80, 0x3f, 0x0c, 0x0c, 0x3c,
-   0xf0, 0xc0, 0x78, 0xf8, 0x0f, 0x07, 0x0e, 0x30, 0xc0, 0x01, 0x9c, 0x03,
-   0xff, 0xf0, 0x3f, 0x00, 0x7f, 0x0c, 0x0c, 0x7c, 0xf8, 0xc0, 0x78, 0xf0,
-   0x8f, 0x03, 0x0c, 0x30, 0xc0, 0x00, 0x0e, 0x07, 0x03, 0x00, 0x3c, 0x00,
-   0xe0, 0x0c, 0x0f, 0xef, 0xdc, 0xcc, 0xfc, 0x00, 0xcc, 0x01, 0x0c, 0x30,
-   0xc0, 0x00, 0x07, 0x0e, 0x03, 0x00, 0x3c, 0x00, 0xe0, 0x9c, 0x9f, 0xcf,
-   0xcf, 0xff, 0xce, 0x01, 0xee, 0x00, 0x1c, 0x30, 0xe0, 0x00, 0x03, 0x0c,
-   0x03, 0x00, 0x3c, 0xc0, 0x7f, 0xf8, 0xf9, 0x8d, 0x87, 0x7f, 0x87, 0xf3,
-   0xf7, 0x3f, 0x38, 0x30, 0x70, 0x00, 0x00, 0x00, 0x03, 0x00, 0x3c, 0xc0,
-   0x3f, 0xf0, 0xf0, 0x0c, 0x03, 0x33, 0x03, 0xf3, 0xf3, 0x3f, 0x30, 0x30,
-   0x30, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };

src/bitmaps/font_dblsize_extra.xbm

@@ -1,14 +0,0 @@
-#define font_extra_dblsize_width 60
-#define font_extra_dblsize_height 16
-static unsigned char font_extra_dblsize_bits[] = {
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x30, 0xc0, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x78, 0xc0, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0xfc, 0xc0, 0x80, 0xff, 0x00, 0x00, 0xff, 0x01, 0xce, 0xc1, 0x80, 0xff,
-   0x01, 0x80, 0xff, 0x01, 0x87, 0xc3, 0x00, 0xb0, 0x03, 0xc0, 0x0d, 0x00,
-   0x33, 0xc3, 0x00, 0x36, 0xc7, 0xe3, 0x6c, 0x00, 0x30, 0xc0, 0x00, 0x37,
-   0xce, 0x73, 0xec, 0x00, 0x30, 0xc0, 0x80, 0x33, 0xdc, 0x3b, 0xcc, 0x01,
-   0x30, 0xcc, 0xcc, 0x31, 0xd8, 0x1b, 0x8c, 0x03, 0x30, 0x1c, 0xee, 0x00,
-   0xc0, 0x03, 0x00, 0x07, 0x30, 0x38, 0x77, 0x00, 0xfe, 0x7f, 0x00, 0x0e,
-   0x30, 0xf0, 0x33, 0x00, 0xfe, 0x7f, 0x00, 0x0c, 0x30, 0xe0, 0x01, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x30, 0xc0, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };

src/bitmaps/font_extra.xbm

@@ -1,6 +0,0 @@
-#define font_extra_6x1_width 30
-#define font_extra_6x1_height 8
-static unsigned char font_extra_6x1_bits[] = {
-   0x84, 0x00, 0x00, 0x00, 0x8e, 0xf8, 0x00, 0x1f, 0x91, 0x40, 0x99, 0x02,
-   0x84, 0x50, 0x5a, 0x0a, 0x24, 0x4a, 0x18, 0x12, 0xc4, 0x05, 0xff, 0x20,
-   0x84, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };

src/bitmaps/font_midsize.xbm

@@ -1,99 +0,0 @@
-#define doublefont_width 128
-#define doublefont_height 72
-static unsigned char doublefont_bits[] = {
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x60, 0x0c, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x18, 0x6c, 0x00, 0x10, 0xc2, 0x1c, 0x18,
-   0x30, 0x18, 0x00, 0x00, 0x00, 0x00, 0x00, 0xc0, 0x00, 0x18, 0x6c, 0x6c,
-   0x7c, 0x67, 0x36, 0x18, 0x18, 0x30, 0x00, 0x00, 0x00, 0x00, 0x00, 0x60,
-   0x00, 0x18, 0x6c, 0x6c, 0xd6, 0x67, 0x36, 0x18, 0x18, 0x30, 0x00, 0x18,
-   0x00, 0x00, 0x00, 0x60, 0x00, 0x18, 0x00, 0xfe, 0x16, 0x32, 0x1e, 0x18,
-   0x0c, 0x60, 0x6c, 0x18, 0x00, 0x00, 0x00, 0x30, 0x00, 0x18, 0x00, 0x6c,
-   0x1e, 0x18, 0x0c, 0x00, 0x0c, 0x60, 0x38, 0x18, 0x00, 0x00, 0x00, 0x18,
-   0x00, 0x18, 0x00, 0x6c, 0x7c, 0x18, 0x9e, 0x00, 0x0c, 0x60, 0xfe, 0xff,
-   0x00, 0xff, 0x00, 0x18, 0x00, 0x18, 0x00, 0xfe, 0xf0, 0x4c, 0xf3, 0x00,
-   0x0c, 0x60, 0x38, 0x18, 0x38, 0x00, 0x00, 0x0c, 0x00, 0x18, 0x00, 0x6c,
-   0xd0, 0xe6, 0x63, 0x00, 0x18, 0x30, 0x6c, 0x18, 0x38, 0x00, 0x00, 0x06,
-   0x00, 0x00, 0x00, 0x6c, 0xd6, 0xe6, 0x73, 0x00, 0x18, 0x30, 0x00, 0x18,
-   0x30, 0x00, 0x18, 0x06, 0x00, 0x18, 0x00, 0x00, 0x7c, 0x43, 0xde, 0x00,
-   0x30, 0x18, 0x00, 0x00, 0x30, 0x00, 0x3c, 0x03, 0x00, 0x00, 0x00, 0x00,
-   0x10, 0x00, 0x00, 0x00, 0x60, 0x0c, 0x00, 0x00, 0x18, 0x00, 0x18, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x1e, 0x0c, 0x1e, 0x1e, 0x10, 0x3f, 0x1c, 0x3f,
-   0x1e, 0x1e, 0x00, 0x00, 0x60, 0x00, 0x06, 0x7c, 0x33, 0x0e, 0x33, 0x33,
-   0x18, 0x03, 0x36, 0x33, 0x33, 0x33, 0x18, 0x18, 0x30, 0x00, 0x0c, 0xc6,
-   0x33, 0x0f, 0x33, 0x33, 0x18, 0x03, 0x33, 0x1b, 0x33, 0x33, 0x3c, 0x3c,
-   0x18, 0x00, 0x18, 0xc6, 0x33, 0x0c, 0x30, 0x30, 0x1c, 0x1f, 0x03, 0x18,
-   0x33, 0x33, 0x18, 0x18, 0x0c, 0x00, 0x30, 0xc0, 0x33, 0x0c, 0x18, 0x1c,
-   0x1e, 0x33, 0x1f, 0x0c, 0x1e, 0x33, 0x00, 0x00, 0x06, 0xff, 0x60, 0x60,
-   0x33, 0x0c, 0x18, 0x30, 0x1b, 0x30, 0x33, 0x0c, 0x1e, 0x3e, 0x00, 0x00,
-   0x06, 0x00, 0x60, 0x30, 0x33, 0x0c, 0x0c, 0x30, 0x1b, 0x30, 0x33, 0x0c,
-   0x33, 0x30, 0x18, 0x38, 0x0c, 0x00, 0x30, 0x18, 0x33, 0x0c, 0x06, 0x33,
-   0x3f, 0x33, 0x33, 0x0c, 0x33, 0x33, 0x3c, 0x38, 0x18, 0xff, 0x18, 0x00,
-   0x33, 0x0c, 0x03, 0x33, 0x18, 0x33, 0x33, 0x0c, 0x33, 0x1b, 0x18, 0x30,
-   0x30, 0x00, 0x0c, 0x18, 0x1e, 0x3f, 0x3f, 0x1e, 0x18, 0x1e, 0x1e, 0x0c,
-   0x1e, 0x0e, 0x00, 0x30, 0x60, 0x00, 0x06, 0x18, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x18, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x78, 0x18, 0x3f, 0x7c, 0x3f, 0xfe, 0xff, 0x7c,
-   0xc3, 0x7e, 0x78, 0xc3, 0x06, 0xc3, 0xc3, 0x3c, 0xcc, 0x3c, 0x63, 0xc6,
-   0x63, 0x06, 0x03, 0xc6, 0xc3, 0x18, 0x60, 0x63, 0x06, 0xe7, 0xc7, 0x66,
-   0xcc, 0x66, 0xc3, 0x83, 0xc3, 0x06, 0x03, 0x03, 0xc3, 0x18, 0x60, 0x33,
-   0x06, 0xff, 0xcf, 0xc3, 0x78, 0xc3, 0x63, 0x03, 0xc3, 0x06, 0x03, 0x03,
-   0xc3, 0x18, 0x60, 0x1b, 0x06, 0xdb, 0xcf, 0xc3, 0x00, 0xc3, 0x3f, 0x03,
-   0xc3, 0x7e, 0x3f, 0x03, 0xff, 0x18, 0x60, 0x0f, 0x06, 0xdb, 0xdb, 0xc3,
-   0x00, 0xc3, 0x63, 0x03, 0xc3, 0x06, 0x03, 0xe3, 0xc3, 0x18, 0x60, 0x0f,
-   0x06, 0xdb, 0xdb, 0xc3, 0x00, 0xff, 0xc3, 0x03, 0xc3, 0x06, 0x03, 0xc3,
-   0xc3, 0x18, 0x60, 0x1b, 0x06, 0xc3, 0xf3, 0xc3, 0x00, 0xc3, 0xc3, 0x83,
-   0xc3, 0x06, 0x03, 0xc3, 0xc3, 0x18, 0x62, 0x33, 0x06, 0xc3, 0xe3, 0xc3,
-   0x00, 0xc3, 0x63, 0xc6, 0x63, 0x06, 0x03, 0xc6, 0xc3, 0x18, 0x36, 0x63,
-   0x06, 0xc3, 0xe3, 0x66, 0x00, 0xc3, 0x3f, 0x7c, 0x3f, 0xfe, 0x03, 0x7c,
-   0xc3, 0x7e, 0x1c, 0xc3, 0xfe, 0xc3, 0xc3, 0x3c, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7c,
-   0x00, 0x7c, 0x00, 0x00, 0x7f, 0x3c, 0x7f, 0x7e, 0xff, 0xc3, 0xc3, 0xc3,
-   0xc3, 0xc3, 0xfe, 0x0c, 0x03, 0x60, 0x18, 0x00, 0xc3, 0x66, 0xc3, 0xc3,
-   0x18, 0xc3, 0xc3, 0xc3, 0xc3, 0xc3, 0xc0, 0x0c, 0x06, 0x60, 0x3c, 0x00,
-   0xc3, 0xc3, 0xc3, 0x03, 0x18, 0xc3, 0xc3, 0xc3, 0x66, 0x66, 0xc0, 0x0c,
-   0x06, 0x60, 0x66, 0x00, 0xc3, 0xc3, 0xc3, 0x03, 0x18, 0xc3, 0x66, 0xc3,
-   0x3c, 0x3c, 0x60, 0x0c, 0x0c, 0x60, 0x42, 0x00, 0x7f, 0xc3, 0x7f, 0x7e,
-   0x18, 0xc3, 0x66, 0xdb, 0x18, 0x18, 0x30, 0x0c, 0x18, 0x60, 0x00, 0x00,
-   0x03, 0xc3, 0x1f, 0xc0, 0x18, 0xc3, 0x66, 0xdb, 0x18, 0x18, 0x18, 0x0c,
-   0x18, 0x60, 0x00, 0x00, 0x03, 0xdb, 0x33, 0xc0, 0x18, 0xc3, 0x3c, 0xdb,
-   0x3c, 0x18, 0x0c, 0x0c, 0x30, 0x60, 0x00, 0x00, 0x03, 0xf3, 0x63, 0xc0,
-   0x18, 0xc3, 0x3c, 0xff, 0x66, 0x18, 0x06, 0x0c, 0x60, 0x60, 0x00, 0x00,
-   0x03, 0x66, 0xc3, 0xc3, 0x18, 0x66, 0x18, 0xe7, 0xc3, 0x18, 0x06, 0x0c,
-   0x60, 0x60, 0x00, 0x00, 0x03, 0xbc, 0xc3, 0x7e, 0x18, 0x3c, 0x18, 0xc3,
-   0xc3, 0x18, 0xfe, 0x0c, 0xc0, 0x60, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7c, 0x00, 0x7c, 0x00, 0xff,
-   0x06, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x0c, 0x00, 0x03, 0x00, 0x60, 0x00, 0x38, 0x00,
-   0x03, 0x0c, 0x60, 0x06, 0x0e, 0x00, 0x00, 0x00, 0x18, 0x00, 0x03, 0x00,
-   0x60, 0x00, 0x6c, 0x00, 0x03, 0x0c, 0x60, 0x06, 0x0c, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x03, 0x00, 0x60, 0x00, 0x6c, 0x00, 0x03, 0x00, 0x00, 0x06,
-   0x0c, 0x00, 0x00, 0x00, 0x00, 0x3c, 0x1b, 0x3c, 0x6c, 0x1c, 0x0c, 0x5e,
-   0x1b, 0x0e, 0x78, 0x26, 0x0c, 0x35, 0x1b, 0x1c, 0x00, 0x66, 0x37, 0x66,
-   0x76, 0x36, 0x0c, 0x73, 0x37, 0x0c, 0x60, 0x36, 0x0c, 0x6b, 0x37, 0x36,
-   0x00, 0x60, 0x63, 0x03, 0x63, 0x63, 0x1f, 0x33, 0x63, 0x0c, 0x60, 0x1e,
-   0x0c, 0x6b, 0x63, 0x63, 0x00, 0x7e, 0x63, 0x03, 0x63, 0x7f, 0x0c, 0x1e,
-   0x63, 0x0c, 0x60, 0x0e, 0x0c, 0x6b, 0x63, 0x63, 0x00, 0x63, 0x63, 0x03,
-   0x63, 0x03, 0x0c, 0x03, 0x63, 0x0c, 0x63, 0x1e, 0x0c, 0x6b, 0x63, 0x63,
-   0x00, 0x73, 0x37, 0x66, 0x76, 0x66, 0x0c, 0x3e, 0x63, 0x0c, 0x63, 0x36,
-   0x0c, 0x6b, 0x63, 0x36, 0x00, 0x6e, 0x1b, 0x3c, 0x6c, 0x3c, 0x0c, 0x63,
-   0x63, 0x3f, 0x63, 0x66, 0x3f, 0x6b, 0x63, 0x1c, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x3e, 0x00, 0x00, 0x3e, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x38,
-   0x00, 0x0e, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x0c, 0x0c, 0x18, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-   0x0c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0c, 0x0c, 0x18, 0x08, 0x08,
-   0x00, 0x00, 0x00, 0x00, 0x0c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0c,
-   0x0c, 0x18, 0x10, 0x04, 0x1f, 0x7c, 0x3b, 0x3e, 0x3f, 0x63, 0x63, 0x63,
-   0x63, 0x63, 0x3f, 0x0c, 0x0c, 0x18, 0x20, 0x02, 0x33, 0x66, 0x6e, 0x63,
-   0x0c, 0x63, 0x63, 0x63, 0x36, 0x63, 0x30, 0x06, 0x0c, 0x30, 0x7f, 0x7f,
-   0x63, 0x63, 0x06, 0x03, 0x0c, 0x63, 0x36, 0x6b, 0x1c, 0x63, 0x18, 0x06,
-   0x0c, 0x30, 0x7f, 0x7f, 0x73, 0x67, 0x06, 0x3e, 0x0c, 0x63, 0x36, 0x6b,
-   0x08, 0x73, 0x0c, 0x0c, 0x0c, 0x18, 0x20, 0x02, 0x1f, 0x7c, 0x06, 0x60,
-   0x0c, 0x63, 0x1c, 0x6b, 0x1c, 0x6c, 0x06, 0x0c, 0x0c, 0x18, 0x10, 0x04,
-   0x03, 0x60, 0x06, 0x63, 0x6c, 0x76, 0x1c, 0x7f, 0x36, 0x60, 0x03, 0x0c,
-   0x0c, 0x18, 0x08, 0x08, 0x03, 0x60, 0x06, 0x3e, 0x38, 0x6c, 0x08, 0x36,
-   0x63, 0x33, 0x3f, 0x0c, 0x0c, 0x18, 0x00, 0x00, 0x03, 0x60, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x1e, 0x00, 0x38, 0x00, 0x0e, 0x00, 0x00 };

src/bitmaps/font_small.xbm

@@ -1,38 +0,0 @@
-#define font_small_width 80
-#define font_small_height 42
-static unsigned char font_small_bits[] = {
-   0x80, 0x28, 0x00, 0x02, 0x20, 0x44, 0x00, 0x00, 0x00, 0x00, 0x80, 0x28,
-   0xe5, 0x92, 0x20, 0x82, 0x28, 0x02, 0x00, 0x40, 0x80, 0xa8, 0x5f, 0x48,
-   0x21, 0x82, 0x10, 0x02, 0x00, 0x20, 0x80, 0x00, 0xe5, 0x84, 0x00, 0x82,
-   0xb8, 0x0f, 0x1e, 0x10, 0x00, 0x80, 0x4f, 0x53, 0x01, 0x82, 0x10, 0xc2,
-   0x80, 0x09, 0x80, 0x00, 0xe5, 0x90, 0x02, 0x44, 0x28, 0x42, 0x80, 0x01,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x20, 0x00, 0x00, 0x84, 0x98,
-   0x47, 0x9e, 0x79, 0xc6, 0x00, 0x00, 0x00, 0x20, 0xca, 0x24, 0x64, 0x42,
-   0x40, 0x29, 0x19, 0x83, 0x80, 0x50, 0x8a, 0x20, 0x53, 0xce, 0x21, 0x26,
-   0x19, 0x43, 0x1e, 0x41, 0x8a, 0x10, 0xf4, 0x50, 0x22, 0xc9, 0x01, 0x20,
-   0x00, 0x22, 0x8a, 0x88, 0x44, 0x52, 0x12, 0x09, 0x19, 0x43, 0x1e, 0x01,
-   0xc4, 0x3d, 0x43, 0x8c, 0x11, 0xc6, 0x18, 0x81, 0x80, 0x20, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x80, 0x00, 0x00, 0x00, 0xc4, 0x1c, 0x73, 0xde,
-   0x33, 0xc9, 0xa1, 0x14, 0x62, 0x32, 0x2a, 0xa5, 0x94, 0x42, 0x48, 0x89,
-   0xa0, 0x12, 0xf6, 0x4a, 0x24, 0x9d, 0x90, 0xce, 0x09, 0x8f, 0xa0, 0x11,
-   0xea, 0x4a, 0xe0, 0xa5, 0x90, 0x42, 0x68, 0x89, 0xa0, 0x11, 0x62, 0x4b,
-   0x20, 0xa5, 0x94, 0x42, 0x48, 0x89, 0xa4, 0x12, 0x62, 0x4b, 0x20, 0x1d,
-   0x73, 0x5e, 0x70, 0xc9, 0x99, 0xf4, 0x62, 0x32, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xc7, 0x1c, 0xe3, 0x52, 0x8a, 0x49,
-   0x3d, 0x07, 0x1c, 0x01, 0x29, 0xa5, 0x44, 0x52, 0x8a, 0x49, 0x21, 0x11,
-   0x90, 0x02, 0x29, 0x25, 0x41, 0x52, 0xaa, 0x46, 0x11, 0x21, 0x10, 0x00,
-   0x27, 0x1d, 0x42, 0x52, 0xfa, 0x86, 0x08, 0x41, 0x10, 0x00, 0x61, 0x95,
-   0x44, 0x92, 0xd9, 0x89, 0x04, 0x81, 0x10, 0x00, 0xc1, 0x24, 0x43, 0x8c,
-   0x89, 0x89, 0x3c, 0x07, 0x1c, 0x78, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x02, 0x04, 0x80, 0x00, 0x01, 0x81, 0xa0, 0x60,
-   0x00, 0x00, 0x04, 0x04, 0x80, 0x80, 0x02, 0x01, 0x80, 0x40, 0x00, 0x00,
-   0xc0, 0x1d, 0xe3, 0x8c, 0x70, 0xc7, 0xa0, 0x42, 0xd2, 0x31, 0x20, 0xa5,
-   0x90, 0xda, 0x49, 0x89, 0xa0, 0x41, 0x7e, 0x4a, 0xa0, 0xa5, 0x90, 0x86,
-   0x30, 0x89, 0xa0, 0x42, 0x6a, 0x4a, 0x40, 0x1d, 0xe3, 0x8c, 0x08, 0xc9,
-   0xa9, 0xe4, 0x6a, 0x32, 0x00, 0x00, 0x00, 0x00, 0x70, 0x00, 0x10, 0x00,
-   0x00, 0x00, 0x00, 0x00, 0x20, 0x00, 0x00, 0x00, 0x00, 0x44, 0x04, 0x00,
-   0x00, 0x00, 0x20, 0x00, 0x00, 0x00, 0x00, 0x42, 0x88, 0x40, 0xc7, 0x1d,
-   0x77, 0x92, 0x8a, 0x29, 0x3d, 0x43, 0x18, 0x21, 0x29, 0xa5, 0x21, 0x92,
-   0xaa, 0x26, 0x11, 0x42, 0xc8, 0xf3, 0x29, 0x05, 0x26, 0x92, 0xfa, 0x46,
-   0x09, 0x42, 0x08, 0x21, 0xc7, 0x85, 0xc3, 0x1c, 0xd9, 0x89, 0x3c, 0x44,
-   0x84, 0x40, 0x01, 0x01, 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x00, 0x00 };

src/bitmaps/font_small_extra.xbm

@@ -1,6 +0,0 @@
-#define font_small_extra_width 30
-#define font_small_extra_height 7
-static unsigned char font_small_extra_bits[] = {
-   0x84, 0x00, 0x00, 0x00, 0x8e, 0xf8, 0x00, 0x1f, 0x91, 0x40, 0x99, 0x02,
-   0x24, 0x52, 0x5a, 0x0a, 0xc4, 0x49, 0x18, 0x12, 0x84, 0x04, 0xff, 0x20,
-   0x00, 0x00, 0x00, 0x00 };

src/bitmaps/font_tiny.xbm

@@ -1,6 +0,0 @@
-#define font_tiny_width 39
-#define font_tiny_height 5
-static unsigned char font_tiny_bits[] = {
-   0x00, 0xa4, 0xbf, 0xff, 0x7f, 0x00, 0x3a, 0xb2, 0x09, 0x5b, 0x07, 0x2a,
-   0xf9, 0xbf, 0x7e, 0x00, 0xaa, 0x90, 0xac, 0x4a, 0x00, 0xf4, 0x9f, 0xbf,
-   0x7e };

src/buzzer.cpp

@@ -56,7 +56,7 @@ static const pm_uint8_t beepTab[] PROGMEM = {
 void beep(uint8_t val)
 {
 #if defined(HAPTIC) && !defined(AUDIO)
-  haptic.event(val==0 ? AU_KEYPAD_UP : (val==4 ? AU_ERROR : AU_TIMER_10+beepAgain));
+  haptic.event(val==0 ? AU_KEYPAD_UP : (val==4 ? AU_ERROR : AU_TIMER_LT10+beepAgain));
 #endif
 
 #if !defined(AUDIO)

src/buzzer.h

@@ -70,8 +70,6 @@ void beep(uint8_t val);
     #define AUDIO_TIMER_MINUTE(t)  playDuration(t)
     #define AUDIO_TIMER_30()       PUSH_SYSTEM_PROMPT(AU_TIMER_30)
     #define AUDIO_TIMER_20()       PUSH_SYSTEM_PROMPT(AU_TIMER_20)
-    #define AUDIO_TIMER_10()       PUSH_SYSTEM_PROMPT(AU_TIMER_10)
-    #define AUDIO_TIMER_LT3(x)     PUSH_SYSTEM_PROMPT(AU_TIMER_LT3)
   #else
     #define AUDIO_TADA()
     #define AUDIO_TX_BATTERY_LOW() beep(4)
@@ -80,8 +78,6 @@ void beep(uint8_t val);
     #define AUDIO_TIMER_MINUTE(t)  beep(2)
     #define AUDIO_TIMER_30()       { beepAgain=2; beep(2); }
     #define AUDIO_TIMER_20()       { beepAgain=1; beep(2); }
-    #define AUDIO_TIMER_10()       beep(2)
-    #define AUDIO_TIMER_LT3(x)     beep(2)
   #endif
 
   #define AUDIO_KEYPAD_UP()        beep(0)
@@ -92,6 +88,7 @@ void beep(uint8_t val);
   #define AUDIO_ERROR()            beep(4)
   #define AUDIO_MIX_WARNING(x)     beep(1)
   #define AUDIO_POT_STICK_MIDDLE() beep(2)
+  #define AUDIO_TIMER_LT10(x)      beep(2)
   #define AUDIO_VARIO_UP()         _beep(1)
   #define AUDIO_VARIO_DOWN()       _beep(1)
   #define AUDIO_TRIM(event, f)     { if (!IS_KEY_FIRST(event)) warble = true; beep(1); }

src/eeprom_raw.cpp

@@ -390,7 +390,7 @@ void eeLoadModel(uint8_t id)
 
     for (uint8_t i=0; i<MAX_TIMERS; i++) {
       if (g_model.timers[i].persistent) {
-        s_timerVal[i] = g_model.timers[i].value;
+        timersStates[i].val = g_model.timers[i].value;
       }
     }
 
@@ -470,8 +470,8 @@ void eeReadAll()
     for (uint32_t i=0; i<MAX_MODELS; i++)
       eeDeleteModel(i);
 
-    STORE_GENERALVARS;
-    STORE_MODELVARS;
+    eeDirty(EE_GENERAL);
+    eeDirty(EE_MODEL);
   }
   else {
     eeLoadModelHeaders() ;

src/eeprom_rlc.cpp

@@ -527,7 +527,7 @@ bool RlcFile::copy(uint8_t i_fileDst, uint8_t i_fileSrc)
 
   uint8_t buf[BS-sizeof(blkid_t)];
   uint8_t len;
-  while ((len=theFile2.read(buf, BS-sizeof(blkid_t))))
+  while ((len=theFile2.read(buf, sizeof(buf))))
   {
     write(buf, len);
     if (write_errno() != 0) {
@@ -958,7 +958,7 @@ void eeLoadModel(uint8_t id)
 #if !defined(PCBSTD)
     for (uint8_t i=0; i<MAX_TIMERS; i++) {
       if (g_model.timers[i].persistent) {
-        s_timerVal[i] = g_model.timers[i].value;
+        timersStates[i].val = g_model.timers[i].value;
       }
     }
 #endif

src/fonts/std/font_cz_04x06.lbm

@@ -0,0 +1 @@
+0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

src/fonts/std/font_cz_08x10.lbm

@@ -0,0 +1 @@
+0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

src/fonts/std/font_cz_10x14.lbm

@@ -0,0 +1 @@
+0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

src/fonts/std/font_de_04x06.lbm

@@ -0,0 +1 @@
+0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

src/fonts/std/font_de_08x10.lbm

@@ -0,0 +1 @@
+0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

src/fonts/std/font_es_04x06.lbm

@@ -0,0 +1 @@
+0x3e,0x09,0x12,0x3d,0x00,0x3a,0x11,0x0a,0x39,0x00,

src/fonts/std/font_es_08x10.lbm

@@ -0,0 +1 @@
+0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

src/fonts/std/font_fr_04x06.lbm

@@ -0,0 +1 @@
+0x18,0x36,0x2d,0x08,0x00,0x18,0x35,0x2e,0x08,0x00,0x18,0x25,0x16,0x3c,0x00,0x00,0x26,0x3d,0x22,0x00,0x00,0x4c,0x32,0x12,0x00,

src/fonts/std/font_fr_08x10.lbm

@@ -0,0 +1 @@
+0xc0,0x01,0xe0,0x03,0xb4,0x06,0x96,0x04,0xb3,0x04,0xe1,0x06,0xc0,0x02,0x00,0x00,0xc0,0x01,0xe0,0x03,0xb1,0x06,0x93,0x04,0xb6,0x04,0xe4,0x06,0xc0,0x02,0x00,0x00,0x00,0x03,0xa0,0x07,0xb1,0x04,0x93,0x04,0x96,0x02,0xf4,0x07,0xe0,0x07,0x00,0x00,0x04,0x04,0x16,0x04,0xf3,0x07,0xf6,0x07,0x04,0x04,0x00,0x04,0x00,0x00,0xe0,0x00,0xf0,0x01,0x18,0x0b,0x08,0x0e,0x08,0x06,0x18,0x03,0x10,0x01,0x00,0x00,0x00,0x00,

src/fonts/std/font_it_04x06.lbm

@@ -0,0 +1 @@
+0x18,0x25,0x16,0x3c,0x00,0x1c,0x21,0x22,0x3c,0x00,

src/fonts/std/font_it_05x07.lbm

@@ -0,0 +1 @@
+0x20,0x55,0x56,0x54,0x78,0x3c,0x41,0x42,0x20,0x7c,

src/fonts/std/font_it_08x10.lbm

@@ -0,0 +1 @@
+0x00,0x03,0xa0,0x07,0xb2,0x04,0x96,0x04,0x94,0x02,0xf0,0x07,0xe0,0x07,0x00,0x00,0xf0,0x01,0xf0,0x03,0x02,0x06,0x06,0x04,0x04,0x02,0xf0,0x07,0xf0,0x07,0x00,0x00,