Commit Graph

480699 Commits

Author SHA1 Message Date
Marcel Holtmann 0a961a440d Bluetooth: Remove unneeded variable assignment in hmac_sha256
The variable ret does not need to be assigned when declaring it. So
remove this initial assignment.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-20 19:53:11 +03:00
Peter Meerwald f4e2f94d8c iio:kxcjk-1013: Fix endianness in scan_type
driver uses i2c_smbus_read_word_data() to the data in the trigger handler and hence
already does endianness conversion; the I2C chip has data in little endian, but the
value is provides in CPU endianness

Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-07-20 17:52:15 +01:00
Peter Meerwald 9b2a4d35a6 iio:bma180: Missing check for frequency fractional part
val2 should be zero

This will make no difference for correct inputs but will reject
incorrect ones with a decimal part in the value written to the sysfs
interface.

Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
2014-07-20 17:39:47 +01:00
Peter Meerwald 381676d5e8 iio:bma180: Fix scale factors to report correct acceleration units
The userspace interface for acceleration sensors is documented as using
m/s^2 units [Documentation/ABI/testing/sysfs-bus-iio]

The fullscale raw values for the BMA80 corresponds to -/+ 1, 1.5, 2, etc G
depending on the selected mode.

The scale table was converting to G rather than m/s^2.
Change the scaling table to match the documented interface.

See commit 71702e6e, iio: mma8452: Use correct acceleration units,
for a related fix.

Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
2014-07-20 17:38:39 +01:00
Marcel Holtmann 72dd2b2a44 Bluetooth: Fix endian and alignment issue with ath3k version handling
The ath3k driver is treating the version information badly when it
comes to loading the right firmware version and comparing that it
actually matches with the hardware.

Initially this showed up as this:

  CHECK   drivers/bluetooth/ath3k.c
drivers/bluetooth/ath3k.c:373:17: warning: cast to restricted __le32
drivers/bluetooth/ath3k.c:435:17: warning: cast to restricted __le32

However when fixing this by actually using __packed and __le32 for
the ath3_version structure, more issues came up:

  CHECK   drivers/bluetooth/ath3k.c
drivers/bluetooth/ath3k.c:381:32: warning: incorrect type in assignment (different base types)
drivers/bluetooth/ath3k.c:381:32:    expected restricted __le32 [usertype] rom_version
drivers/bluetooth/ath3k.c:381:32:    got int [signed] <noident>
drivers/bluetooth/ath3k.c:382:34: warning: incorrect type in assignment (different base types)
drivers/bluetooth/ath3k.c:382:34:    expected restricted __le32 [usertype] build_version
drivers/bluetooth/ath3k.c:382:34:    got int [signed] <noident>
drivers/bluetooth/ath3k.c:386:28: warning: restricted __le32 degrades to integer
drivers/bluetooth/ath3k.c:386:56: warning: restricted __le32 degrades to integer

This patch fixes every instance of the firmware version handling and
makes sure it is endian safe and uses proper unaligned access.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-20 18:42:14 +03:00
Srinivas Pandruvada c1288b8338 iio: accel: kxcjk-1013: Increment ref counter for indio_dev->trig
Assigning indio_dev->trig is not a good idea, as this can result in
wrong reference count for trigger device. If assigned, it is better to
increment reference counter by calling iio_trigger_get.
Refer to http://www.spinics.net/lists/linux-iio/msg13669.html for discussion
with Jonathan.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-07-20 16:37:52 +01:00
Srinivas Pandruvada 59bfeaba3b iio: accel: kxcjk-1013: Use try_reenable to ack intr
This chip needs explicit interrupt ack, introducing try_reenable
callback. Also removed separate function to ack interrupt as this
doesn't add any value.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-07-20 16:24:22 +01:00
Srinivas Pandruvada f0ca974920 iio: accel: kxcjk-1013: Fix setting frequency
Fix issue with setting of 12.5 and 6.25 HZ. The match of val2 fails.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-07-20 16:18:58 +01:00
Lars-Peter Clausen 61bd55ce16 iio: buffer: Fix demux table creation
When creating the demux table we need to iterate over the selected scan mask for
the buffer to get the samples which should be copied to destination buffer.
Right now the code uses the mask which contains all active channels, which means
the demux table contains entries which causes it to copy all the samples from
source to destination buffer one by one without doing any demuxing.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
2014-07-20 15:44:39 +01:00
Johan Hedberg d1d588c181 Bluetooth: Disable HCI_CONNECTABLE based passive scanning for now
When HCI_CONNECTABLE is set the code has been enabling passive scanning
in order to be consistent with BR/EDR and accept connections from any
device doing directed advertising to us. However, some hardware
(particularly CSR) can get very noisy even when doing duplicates
filtering, making this feature waste resources.

Considering that the feature is for fairly corner-case use (devices
who'd use directed advertising would likely be in the whitelist anyway)
it's better to disable it for now. It may still be brought back later,
possibly with a better implementation (e.g. through improved scan
parameters).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-07-20 16:15:38 +02:00
Reyad Attiyat abea9c62c3 iio: hid-sensor-magn-3d: Add support for rotation from north
Add the HID usage attribute ID's and IIO channel info for rotation
from north support.

Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-07-20 13:39:35 +01:00
Reyad Attiyat 2a96540a5c iio: hid-sensor-magn-3d: Scan for usage attributes before setting up iio channels
Scan for and count the HID usage attributes supported by the driver.
This allows for the driver to only setup the IIO channels for the
sensor usages present in the HID USB reports.

Changes from v5
-Fixed kernel panic from invalid pointer dereference
-Fixed variable assignment style

Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-07-20 13:37:52 +01:00
Reyad Attiyat 11b8ddab81 iio: types: Added support for rotation from north usage attributes
Added the rotation from north usage attributes to the iio modifier enum and to the iio modifier names array.

Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-07-20 13:34:45 +01:00
Reyad Attiyat b531db8456 iio: Documentation: Add documentation for rotation from north sensor usage attributes
Added documentation for the sysfs attributes supported by the rotation from north
sensor.

Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-07-20 13:30:59 +01:00
Richard Weinberger bb6a1b2e18 um: segv: Save regs only in case of a kernel mode fault
...otherwise me lose user mode regs and the resulting
stack trace is useless.

Signed-off-by: Richard Weinberger <richard@nod.at>
2014-07-20 13:39:27 +02:00
Jean Delvare 0f6ba0d15f i2c: stub: Avoid an array overrun on I2C block transfers
I2C block transfers can have a size up to 32 bytes. If starting close
to the end of the address space, there may not be enough room to write
that many bytes (on I2C block writes) or not enough bytes to be read
(on I2C block reads.) In that case, we must shorten the transfer so
that it does not exceed the address space.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-07-20 13:25:29 +02:00
Richard Weinberger 468f65976a um: Fix hung task in fix_range_common()
If do_ops() fails we have to release current->mm->mmap_sem
otherwise the failing task will never terminate.

Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
2014-07-20 13:16:20 +02:00
Richard Weinberger 284e6d3951 um: Ensure that a stub page cannot get unmapped
Trinity discovered an execution path such that a task
can unmap his stub page.

Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
2014-07-20 13:09:15 +02:00
Richard Weinberger ae5db6d123 Revert "um: Fix wait_stub_done() error handling"
This reverts commit 0974a9cadc.
The real for for that issue is to release current->mm->mmap_sem in
fix_range_common().

Signed-off-by: Richard Weinberger <richard@nod.at>
2014-07-20 12:56:34 +02:00
Anish Bhatt e81fbf6cd6 libcxgbi:cxgb4i Guard ipv6 code with a config check
Fixes: fc8d0590d9 ("libcxgbi: Add ipv6 api to driver")
Fixes: 759a0cc5a3 ("cxgb4i: Add ipv6 code to driver, call into libcxgbi ipv6
api")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-20 00:45:54 -07:00
Wei Yongjun 0a0ea07d3d HSI: ssi_protocol: Fix sparse non static symbol warning
Fixes the following sparse warning:

drivers/hsi/clients/ssi_protocol.c:904:6: warning:
 symbol 'ssip_port_event' was not declared. Should it be static?

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-07-20 09:31:16 +02:00
Wei Yongjun c128d39737 power_supply: Fix sparse non static symbol warning
Fixes the following sparse warnings:

drivers/power/power_supply_core.c:540:5: warning:
 symbol '__power_supply_register' was not declared. Should it be static?

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-07-20 09:22:34 +02:00
Lv Zheng a8278efd84 ACPICA: Linux: Add stub support for Linux specific variables and functions.
There are global variables and functions not upstreamed to the ACPICA code
base.  Such symbols still can be referenced by external users as they are
listed in the acpixf.h.  This patch uses ACPI_GLOBAL and
ACPI_EXTERNAL_RETURN_STATUS mechanism to add stub support for such symbols.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-07-20 01:34:57 +02:00
Olof Johansson aaaa10b096 Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v3.17" from Kukjin Kim:

exynos3250: add i2s dt for audio interface

exynos4
 - cleanup arm-pmu node because of 4 pmu on
   exynos4412 but 2 pmu on other exynos4 SoCs
 - add support sub-nodes to exynos usb host for exynos4

exynos4412-odroid-common
 - fix T-FLASH hotplug detection
 - disable 'always on' for BUCK8
 - add support for GPIO based buttons
 - add MAX98090 audio codec

exynos4412-odroidx2 and exynos4412-odroidu3
- refactor exynos4412-odroidx and exynos4412-odroid-common
  for odroid-x2 and u2/u3

exynos4412-odroidx
 - add support for USB phy, host and device
 - enable common hardware blocks, secure firmware calls,
   watchdog, g2d and fimc (mem2mem) multimedia accelerators
 - add support for USB phy, host and device
 - correct memory size

exynos5410
 - fill in CPU clock-frequency property to avoid warning

exynos5420
 - remove display pd because of instability

exynos5420-peach-pit and exynos5800-peach-pi
 - sort nodes each other to check its differences easily
 - enable audio support and add sound-card name property
 - add mask-tpm-reset node
 - add cros_ec including keyboard, i2c tunnel and tps65090
   and battery under the i2c tunnel

* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Add I2S dt node for exynos3250
  ARM: dts: Add cros_ec to exynos5420-peach-pit and exynos5800-peach-pi
  ARM: dts: clean up arm-pmu node for exynos4
  ARM: dts: remove display power domain for exynos5420
  ARM: dts: Add sound nodes for Odroid-X2/U3 boards
  ARM: dts: fix T-FLASH hotplug detection for exynos4412-odroid-common
  ARM: dts: add support for GPIO buttons for exynos4412-odroid
  ARM: dts: disable 'always on' for BUCK8 regulator for exynos4412-odroid-common
  ARM: dts: refactor Odroid DTS file and add support for Odroid X2 and U2/U3
  ARM: dts: correct memory size for exynos4412-odroidx
  ARM: dts: add support for USB phy, host and device for exynos4412-odroidx
  ARM: dts: enable common hardware blocks for exynos4412-odroidx
  ARM: dts: add port sub-nodes to exynos usb host modules for exynos4
  ARM: dts: Add mask-tpm-reset node in exynos5800-peach-pi
  ARM: dts: Add mask-tpm-reset node in exynos5420-peach-pit
  ARM: dts: Add sound-card name for Snow/Peach-Pit/Peach-Pi
  ARM: dts: Fill in CPU clock-frequency for exynos5410
  ARM: dts: Sort nodes within Peach-pit/Peach-pi dts files
  ARM: dts: Enable audio support for exynos5800-peach-pi
2014-07-19 15:06:48 -07:00
Olof Johansson f37ac9e5a4 Merge tag 'exynos-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung exynos cpuidle update for v3.17" from Kukjin Kim:

- add callbacks exynos_suspend() and exynos_powered_up()
  for support cpuidle through mcpm
- skip exynos_cpuidle for exynos5420 because is uses
  cpuidle-big-liggle generic cpuidle driver
- add generic functions to calculate cpu number is used
  for pmu and this is required for exynos5420 multi-cluster
- add of_device_id structure for big.LITTLE cpuidle and
  add "samsung,exynos5420" compatible string for exynos5420

* tag 'exynos-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: populate suspend and powered_up callbacks for mcpm
  ARM: EXYNOS: do not allow cpuidle registration for exynos5420
  cpuidle: big.LITTLE: init driver for exynos5420
  cpuidle: big.LITTLE: Add ARCH_EXYNOS entry in config
  ARM: EXYNOS: add generic function to calculate cpu number
  cpuidle: big.LITTLE: add of_device_id structure
  + Linux 3.16-rc5

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 15:03:08 -07:00
Olof Johansson f57c0e049a Merge tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
Merge "Samsung cleanup for v3.17" from Kukjin Kim:

Most of them are for exynos SoCs, remove useless codes and update for
PMU consolidation.

- remove unnecessary header file in mach-exynos/pmu.c
- remove unused code in mach-exynos/common.h
- remove mach-exynos/regs-pmu.h dependency from PD
- remove file path from comment section in mach-exynos

- move SYSREG definitions into mach-exynos/regs-sys.h

- add mapping PMU base address via DT for PMU cleanup

- use staic in mach-exynos/common.h
- update Samsung UART config options for low-level debug

* tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: Add support for mapping PMU base address via DT
  ARM: EXYNOS: Remove "linux/bug.h" from pmu.c
  ARM: EXYNOS: Remove regs-pmu.h header dependency from pm_domain
  ARM: EXYNOS: Remove file path from comment section
  ARM: EXYNOS: Move SYSREG definition into sys-reg specific file
  ARM: EXYNOS: Make exynos machine_ops as static
  ARM: EXYNOS: Remove unused code in common.h
  ARM: debug: Update Samsung UART config options
  + Linux 3.16-rc5

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 15:01:08 -07:00
Sachin Kamat fc3791f3a9 ARM: exynos_defconfig: Update exynos_defconfig
Removed outdated configs. Enabled most of the configs used on latest
Exynos based platforms. This will provide a reference for users trying
to verify and test various features on Exynos based platforms and also
help in detecting breakages by widening the build coverage.

Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
[arun.kk@samsung.com: on Snow, Pit, Pi chromebooks]
Tested-by: Arun Kumar K <arun.kk@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 14:59:32 -07:00
Krzysztof Kozlowski 7310d99ffc ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
Fix building of exynos_defconfig with disabled PM_SLEEP:
CONFIG_PM_SLEEP=n
CONFIG_PM_SLEEP_SMP=n
CONFIG_SUSPEND=n
by moving functions for power up/down of CPU and cluster to platsmp.c

The build error messages:
arch/arm/mach-exynos/built-in.o: In function `exynos_boot_secondary':
arch/arm/mach-exynos/platsmp.c:111: undefined reference to `exynos_cpu_power_state'
arch/arm/mach-exynos/platsmp.c:112: undefined reference to `exynos_cpu_power_up'
arch/arm/mach-exynos/platsmp.c:116: undefined reference to `exynos_cpu_power_state'
make: *** [vmlinux] Error 1

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>,
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 14:59:24 -07:00
Olof Johansson 4e9816d012 Merge tag 'v3.16-rc5' into next/fixes-non-critical
Linux 3.16-rc5
2014-07-19 14:59:07 -07:00
Olof Johansson 46dd1230ba Merge tag 'mvebu-defconfig-3.17-2' of git://git.infradead.org/linux-mvebu into next/defconfig
Merge "ARM: mvebu: defconfig changes for v3.17 (round 2)" from Jason Cooper:

"Here's all the defconfig changes we have for mvebu this time around. The
big one is the removal of kirkwood_defconfig, corresponding to the
mach-kirkwood/ removal in mvebu/soc."

 - mvebu
   * Add appended_dtb support
   * Add devtmpfs support
   * Add 375 network driver
   * Add cpuidle support
   * Add cpufreq support

 - kirkwood
   * Remove kirkwood_defconfig

* tag 'mvebu-defconfig-3.17-2' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: update mvebu_v7_defconfig with cpufreq support
  ARM: mvebu: defconfig: enable cpuidle support in mvebu_v7_defconfig
  ARM: Kirkwood: Remove kirkwood_defconfig
  ARM: mvebu: enable Armada 375 network driver in mvebu_v7_defconfig
  ARM: mvebu: add devtmpfs to mvebu_v5_defconfig
  ARM: mvebu: add appended DTB support in mvebu_v5_defconfig

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 14:30:21 -07:00
Olof Johansson 4338925434 Merge tag 'mvebu-soc-3.17-2' of git://git.infradead.org/linux-mvebu into next/soc
Merge "ARM: mvebu SoC changes for v3.17 (round 2)" from Jason Cooper:

"Yeah, it's just one patch, but it's a beautiful one!  Thanks to the
efforts of many people over the last couple years, and in particular,
Andrew Lunn, Kirkwood has been completely converted to DT."

 - kirkwood
   * Remove mach-kirkwood/, It's fully supported in mach-mvebu/

* tag 'mvebu-soc-3.17-2' of git://git.infradead.org/linux-mvebu:
  ARM: Kirkwood: Remove mach-kirkwood

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 14:28:06 -07:00
Olof Johansson a67f02c98e Merge tag 'tegra-for-3.17-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/defconfig
Merge "ARM: tegra: defconfig updates for 3.17" from Theirry Reding:

This set of patches update the tegra_defconfig by first regenerating on
top of v3.16-rc1 to prune all non-existent symbols or symbols which are
now selected by default.

* tag 'tegra-for-3.17-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: enable igb, stmpe, i2c chardev, lm95245, pwm leds
  ARM: tegra: rebuild tegra_defconfig

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 12:53:10 -07:00
Olof Johansson 223f93ed7e Merge tag 'tegra-for-3.17-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: device tree changes for 3.17" from Thierry Reding:

- New board support:
  * Apalis T30
- HDA support for Tegra124 and Venice2
- Display on Medcom Wide and Roth
- GK20A support on Tegra124
- XUSB pad controller for Tegra124 and Jetson TK1
- Various cleanups

This pulls in the for-3.17/fuse-move, for-3.17/dt-cros-ec-kbd and
for-3.17/xusb-padctl branches to resolve dependencies.

Note that the Apalis T30 support has a runtime dependency on the
for-3.17/pcie-regulators branch, so they should preferably be applied
in that order. I didn't merge that branch into this because Apalis T30
support is new, therefore can't regress, and because the dependency
exists only at runtime.

* tag 'tegra-for-3.17-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (28 commits)
  ARM: tegra: roth: add display DT node
  ARM: tegra: Fix typoed ams,ext-control properties
  ARM: tegra: jetson-tk1: Add XUSB pad controller
  ARM: tegra: tegra124: Add XUSB pad controller
  ARM: tegra: add GK20A GPU to Tegra124 DT
  ARM: tegra: of: add GK20A device tree binding
  ARM: tegra: roth: enable input on mmc clock pins
  ARM: tegra: roth: fix unsupported pinmux properties
  ARM: tegra: Migrate Apalis T30 PCIe power supply scheme
  ARM: tegra: tamonten: add the display to the Medcom Wide
  ARM: tegra: tamonten: add the base board regulators
  ARM: tegra: initial support for apalis t30
  ARM: tegra: jetson-tk1: mark eMMC as non-removable
  ARM: tegra: venice2 - Enable HDA
  ARM: tegra: Add Tegra124 HDA support
  ARM: tegra: Add the EC i2c tunnel to tegra124-venice2
  soc/tegra: fuse: fix dummy functions
  soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
  soc/tegra: Add efuse and apbmisc bindings
  soc/tegra: Add efuse driver for Tegra
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 12:51:26 -07:00
Olof Johansson 58cd070a84 Merge tag 'tegra-for-3.17-xusb-padctl' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Add XUSB pad controller support" from Thierry Reding:

Adds device tree bindings and a driver for the XUSB pad controller found
on Tegra114 and later. This is a prerequisites for PCIe, SATA and XUSB
drivers which are all currently being reviewed or pending for merge.

This is a separate branch in case it needs to be pulled into the pinctrl
tree to resolve conflicts.

* tag 'tegra-for-3.17-xusb-padctl' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  pinctrl: Add NVIDIA Tegra XUSB pad controller support
  of: Add NVIDIA Tegra XUSB pad controller binding

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 12:49:24 -07:00
Mohammad Merajul Islam Molla 4f8eea9b9f cpuidle: fix permission for driver name sysfs node
cpuidle driver name sysfs node is read-only, so permissions should be 0444.

Signed-off-by: Mohammad Merajul Islam Molla <meraj.enigma@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-07-19 21:43:28 +02:00
Andrey Utkin 788606cb88 PM / tools: cpupower: drop negativity check on unsigned value
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80621
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-07-19 21:41:17 +02:00
Olof Johansson b776eec135 Merge tag 'tegra-for-3.17-pcie-regulators' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "ARM: tegra: rework PCIe regulators" from Thierry Reding:

This branch reworks the set of regulators that the Tegra PCIe driver
uses, so that the driver and DT bindings more correctly model what's
really going on in HW. For backwards-compatibility the driver will
fallback to using the old set of regulators if the new ones can't be
found.

I've made this a separate branch in case it needs to be pulled into the
PCIe tree to resolve any conflicts.

* tag 'tegra-for-3.17-pcie-regulators' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: Remove legacy PCIe power supply properties
  PCI: tegra: Remove deprecated power supply properties
  PCI: tegra: Implement accurate power supply scheme
  ARM: tegra: Add new PCIe regulator properties
  PCI: tegra: Overhaul regulator usage

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 12:35:45 -07:00
Olof Johansson c6b659c005 Merge tag 'tegra-for-3.17-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
Merge "ARM: tegra: core code changes for 3.17" from Thierry Reding:

Some of the code that's currently called from the Tegra machine setup
code is moved to regular initcalls. To catch dependency violations, the
various code paths now WARN if they're called to early. Not all of the
potential candidates are converted yet, but those that were have been
verified to work across all supported Tegra generations.

A new function, soc_is_tegra(), is also provided to make sure that the
initcalls can abort early if they aren't run on Tegra, which can happen
for multi-platform builds.

Finally this also moves out the PMC driver to drivers/soc/tegra so that
it can be shared with 64-bit ARM.

This is based on the for-3.17/fuse-move branch. The split is somewhat
arbitrary but allows the dependents of the for-3.17/fuse-move to pull
in as little code as necessary.

* tag 'tegra-for-3.17-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: Convert PMC to a driver
  soc/tegra: fuse: Set up in early initcall
  ARM: tegra: Always lock the CPU reset vector
  ARM: tegra: Setup CPU hotplug in a pure initcall
  soc/tegra: Implement runtime check for Tegra SoCs

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 12:31:22 -07:00
Olof Johansson 23e892929e Merge tag 'tegra-for-3.17-fuse-move' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
Merge "ARM: tegra: move fuse code out of arch/arm" from Thierry Reding:

This branch moves code related to the Tegra fuses out of arch/arm and
into a centralized location which could be shared with ARM64. It also
adds support for reading the fuse data through sysfs.

Included is also some preparatory work that moves Tegra-related header
files from include/linux to include/soc/tegra as suggested by Arnd.

Furthermore the Tegra chip ID is now retrieved using a function rather
than a variable so that sanity checks can be done. This is convenient
in subsequent patches that will move some of the code that's currently
called from Tegra machine setup into regular initcalls so that it can
be reused on 64-bit ARM. The sanity checks help with verifying that no
code tries to obtain the Tegra chip ID before the underlying driver is
properly initialized.

* tag 'tegra-for-3.17-fuse-move' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  soc/tegra: fuse: fix dummy functions
  soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
  soc/tegra: Add efuse and apbmisc bindings
  soc/tegra: Add efuse driver for Tegra
  ARM: tegra: move fuse exports to soc/tegra/fuse.h
  ARM: tegra: export apb dma readl/writel
  ARM: tegra: Use a function to get the chip ID
  ARM: tegra: Sort includes alphabetically
  ARM: tegra: Move includes to include/soc/tegra

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 12:29:11 -07:00
Olof Johansson 7b2a428a33 Merge tag 'sunxi-core-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/soc
Merge "Allwinner core additions for 3.17" from Maxime Ripard:

Nothing very fancy here, only the introduction from the new Allwinner A23 SoC.

* tag 'sunxi-core-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: sunxi: select MFD_SUN6I_PRCM when sun8i arch support is enabled
  ARM: sunxi: Add earlyprintk support using R_UART (sun6i/sun8i)
  ARM: sunxi: Introduce Allwinner A23 support

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 12:22:47 -07:00
Olof Johansson 15bebad68e Merge tag 'sunxi-dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT additions for 3.17" from Maxime Ripard:

Among the few patches that we have so far, there's a few noticeable changes:
 - Introduction of the Allwinner A23 SoC
 - Support for the GMAC on the A31. This is only available so far on the
   boards which bootloader enable the PHY regulator.
 - Addition of the infrared receiver

* tag 'sunxi-dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (22 commits)
  ARM: dts: sun6i: Add Merrii A31 Hummingbird support
  ARM: dts: sun6i: Add ethernet alias for GMAC
  ARM: dts: sun6i: Add A31 GMAC gigabit ethernet controller node
  ARM: dts: sun6i: Add GMAC clock node to the A31 dtsi
  ARM: dts: sun6i: Add pin muxing options for GMAC
  ARM: sun8i: Add PRCM clock and reset controller nodes to the DTSI
  ARM: sun8i: Add reset controller nodes to the DTSI
  ARM: sun8i: Add basic clock nodes to the DTSI
  ARM: dts: sun4i: Add ir node to various boards
  ARM: dts: sun4i: Add ir controller nodes and pinmux
  ARM: dts: sun4i: Add new ba10-tvbox board
  ARM: dts: sun7i: Add board support for LinkSprite pcDuino V3
  ARM: dts: sun7i: Add ir receiver support to a20-i12-tvbox
  ARM: dts: sun7i: Rename sun7i-a20-ir to sun4i-a10-ir
  ARM: dts: sun7i: Add AXP209 support to various boards
  ARM: dts: sun4i: Add AXP209 support to various boards
  ARM: dts: sunxi: Add #interrupt-cells to pinctrl nodes
  ARM: sun8i: dt: Add Ippo-q8h v5 support
  ARM: sunxi: Add Allwinner A23 dtsi
  ARM: sunxi: Add IR controllers on A20 to dtsi
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 12:19:28 -07:00
Olof Johansson 730346236a Merge tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx into next/dt
Merge "Xilinx Zynq changes for v3.17" from Michal Simek:

arm: Xilinx Zynq dt patches for v3.17

- Document and use new cadence serial binding

* tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx:
  ARM: zynq: DT: Migrate UART to Cadence binding
  tty: cadence: Document DT binding
  + Linux 3.16-rc5

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 12:16:34 -07:00
Olof Johansson 1409f3fd5b Merge tag 'imx-dt-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Merge "ARM: imx: device tree updates for 3.17" from Shawn Guo:

The i.MX device tree updates for 3.17:
 - Add device tree sources and pin function header for i.MX6SX SoC
 - Initial imx6sx-sdb board support with FEC, MMC, USB, PMIC, Audio
   and GPIO key enabled
 - New board support: mbimxsd25 and mbimxsd27 from Eukrea, aristainetos
   imx6dl boards, Rex Pro and Basic, Ka-Ro TX6
 - Restructure imx6qdl-wandboard.dtsi for new rev C1 board
 - Split M28EVK and M53EVK into SoM and EVK parts
 - A few correction around SDMA, SSI and SATA device nodes
 - Add eSATA support for Cubox-i board
 - Updates on edmqmx6 to enable PCIe, I2C and CAN
 - Use DT macro for clock ID for imx27 and imx6qdl
 - Add FlexCAN support for VF610 SoC

* tag 'imx-dt-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (125 commits)
  ARM: dts: vf610: add FlexCAN node
  ARM: dts: add initial Rex Basic board support
  ARM: dts: add initial Rex Pro board support
  ARM: dts: mx5: Split M53EVK into SoM and EVK parts
  ARM: dts: imx6: RIoTboard explicitly define pad settings
  ARM: dts: vf610: fix length of eshdc1 register property
  ARM: dts: Restructure imx6qdl-wandboard.dtsi for new rev C1 board.
  ARM: dts: imx53: correct clock-names of SATA node
  ARM: imx6: Align ssi nodes between mx6 variants
  ARM: i.MX27 clk: dts: Use clock defines in DTS files
  ARM: dts: imx: correct sdma compatbile for imx6sl and imx6sx
  ARM: dts: imx6sx-sdb: Add audio support
  ARM: dts: imx6sx: Pass the fsl,fifo-depth property
  ARM: dts: imx6sx: Fix sdma node
  ARM: dts: imx6: edmqmx6: Add can bus
  ARM: dts: imx6: edmqmx6: Add two other i2c buses
  ARM: dts: imx6: edmqmx6: Add PCIe support
  ARM: dts: imx25-pdk: Add USB OTG support
  ARM: dts: i.MX53: add aipstz nodes
  ARM: dts: mxs: Split M28EVK into SoM and EVK parts
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 12:12:57 -07:00
Olof Johansson b40abaf07f Merge tag 'imx-soc-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
Merge "ARM: imx: SoC changes for 3.17" from Shawn Guo:

The i.MX SoC changes for 3.17:
 - Add devicetree support for i.MX1 and i.MX21 clock driver
 - Use CLOCKSOURCE_OF_DECLARE() to initialize timer for DT targets
 - Use of_clk_init() to initialize i.MX25 and i.MX27 clock driver in
   device tree boot
 - Remove i.MX1 camera support
 - Remove i.MX27 IP Camera and Lite-Kit board support
 - Add suspend and cpuidle support for i.mx6sx
 - Clean up unused clk_register_clkdev() lookups
 - Update imx-weim bus driver to support populating devices on a simple
   bus
 - Switch i.MX27 and i.MX6QDL clock driver to use macro for clock IDs
 - Make i.MX51 a DT only platform and clean up the non-DT support code
 - Support disabling supervisor protect via DT
 - Random defconfig updates

* tag 'imx-soc-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (69 commits)
  ARM: imx: clk-vf610: fix FlexCAN clock gating
  ARM: i.MX: Use CLOCKSOURCE_OF_DECLARE() for DT targets
  ARM: i.MX53: globally disable supervisor protect
  ARM: i.MX: allow disabling supervisor protect via DT
  ARM: i.MX27 clk: Add 26 MHz oscillator circuit clock gate
  ARM: i.MX27 clk: Remove unused definitions
  ARM: i.MX27 clk: Introduce DT include for clock provider
  ARM: i.MX: Remove Freescale Logic Product Development i.MX27 Lite-Kit board support
  ARM: i.MX: Remove excess symbols ARCH_MX1, ARCH_MX25 and MACH_MX27
  ARM: i.MX: Remove i.MX1 camera support
  ARM: imx: use PTR_ERR_OR_ZERO
  bus: imx-weim: populate devices on a simple bus
  ARM: imx: build cpu_is_imx6sl function conditionally
  ARM: imx: imx6sx uses imx6q cpuidle code
  ARM: imx: drop PL310 errata 588369 and 727915
  ARM: imx_v6_v7_defconfig: add FSL_EDMA and PRINTK_TIME
  ARM: imx: clk-imx6sx: register SSI/SSI_IPG as shared gate clocks
  ARM: imx_v6_v7_defconfig: Enable flexcan driver for can support
  ARM: imx_v6_v7_defconfig: Enable STMPE gpio support
  ARM: imx: mark .dt_compat as const
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 11:56:39 -07:00
Olof Johansson 0d29db01b3 Merge tag 'renesas-defconfig4-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Merge "Fourth Round of Renesas ARM Based SoC Defconfig Updates for v3.17" from
Simon Horman:

The genmai board code is going away so remove:
 - The genmai defconfig
 - MACH_GENMAI from shmobile defconfig

* tag 'renesas-defconfig4-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: defconfig: Remove MACH_GENMAI
  ARM: shmobile: genmai: remove defconfig

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 11:51:20 -07:00
Eric Sandeen 0bfaa9c5cb btrfs: test for valid bdev before kobj removal in btrfs_rm_device
commit 99994cd btrfs: dev delete should remove sysfs entry
added a btrfs_kobj_rm_device, which dereferences device->bdev...
right after we check whether device->bdev might be NULL.

I don't honestly know if it's possible to have a NULL device->bdev
here, but assuming that it is (given the test), we need to move
the kobject removal to be under that test.

(Coverity spotted this)

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Chris Mason <clm@fb.com>
2014-07-19 11:49:44 -07:00
Liu Bo 98ce2deda2 Btrfs: fix abnormal long waiting in fsync
xfstests generic/127 detected this problem.

With commit 7fc34a62ca, now fsync will only flush
data within the passed range.  This is the cause of the above problem,
-- btrfs's fsync has a stage called 'sync log' which will wait for all the
ordered extents it've recorded to finish.

In xfstests/generic/127, with mixed operations such as truncate, fallocate,
punch hole, and mapwrite, we get some pre-allocated extents, and mapwrite will
mmap, and then msync.  And I find that msync will wait for quite a long time
(about 20s in my case), thanks to ftrace, it turns out that the previous
fallocate calls 'btrfs_wait_ordered_range()' to flush dirty pages, but as the
range of dirty pages may be larger than 'btrfs_wait_ordered_range()' wants,
there can be some ordered extents created but not getting corresponding pages
flushed, then they're left in memory until we fsync which runs into the
stage 'sync log', and fsync will just wait for the system writeback thread
to flush those pages and get ordered extents finished, so the latency is
inevitable.

This adds a flush similar to btrfs_start_ordered_extent() in
btrfs_wait_logged_extents() to fix that.

Reviewed-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
2014-07-19 11:49:44 -07:00
Olof Johansson f097748f39 Merge tag 'keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Merge "Keystone DTS update for 3.17" from Santosh Shilimkar:

Keystone DTS update for 3.17
 - Ethernet clock tree fix.
 - MDIO device tree node. Respective driver update is already queued.
 - Ethernet phy node. Respective driver update is already queued.

* tag 'keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: dts: keystone-evm: add 1g ethernet phys nodes
  ARM: dts: keystone: add mdio devices entries
  ARM: dts: keystone: fix netcp's clocks definitions

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-19 11:49:16 -07:00
Linus Torvalds d057190925 Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
 "The locking department delivers:

   - A rather large and intrusive bundle of fixes to address serious
     performance regressions introduced by the new rwsem / mcs
     technology.  Simpler solutions have been discussed, but they would
     have been ugly bandaids with more risk than doing the right thing.

   - Make the rwsem spin on owner technology opt-in for architectures
     and enable it only on the known to work ones.

   - A few fixes to the lockdep userspace library"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/rwsem: Add CONFIG_RWSEM_SPIN_ON_OWNER
  locking/mutex: Disable optimistic spinning on some architectures
  locking/rwsem: Reduce the size of struct rw_semaphore
  locking/rwsem: Rename 'activity' to 'count'
  locking/spinlocks/mcs: Micro-optimize osq_unlock()
  locking/spinlocks/mcs: Introduce and use init macro and function for osq locks
  locking/spinlocks/mcs: Convert osq lock to atomic_t to reduce overhead
  locking/spinlocks/mcs: Rename optimistic_spin_queue() to optimistic_spin_node()
  locking/rwsem: Allow conservative optimistic spinning when readers have lock
  tools/liblockdep: Account for bitfield changes in lockdeps lock_acquire
  tools/liblockdep: Remove debug print left over from development
  tools/liblockdep: Fix comparison of a boolean value with a value of 2
2014-07-19 06:27:55 -10:00
Linus Torvalds d1743b810d Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
 "Prevent a possible divide by zero in the debugging code"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix possible divide by zero in avg_atom() calculation
2014-07-19 06:26:43 -10:00