URBs for a particular endpoint should complete sequentially. That is,
we shouldn't call the completion handler for one URB until the handler
for the previous URB has returned.
When the OHCI watchdog routine is added, there will be two paths for
completing URBs: interrupt handler and watchdog routine. Their
activities have to be synchronized so that completions don't occur in
multiple threads concurrently.
For that purpose, this patch creates an ohci_work() routine which will
be responsible for calling process_done_list() and finish_unlinks(),
the two routines that detect when an URB is complete. Everything will
funnel through ohci_work(), and it will be careful not to run in more
than one thread at a time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the way ohci-hcd handles the TD done list. In
addition to relying on the TD pointers stored by the controller
hardware, we need to handle TDs that the hardware has forgotten about.
This means the list has to exist even while the dl_done_list() routine
isn't running. That function essentially gets split in two:
update_done_list() reads the TD pointers stored by the hardware and
adds the TDs to the done list, and process_done_list() scans through
the list to handle URB completions. When we detect a TD that the
hardware forgot about, we will be able to add it to the done list
manually and then process it normally.
Since the list is really a queue, and because there can be a lot of
TDs, keep the existing singly linked implementation. To insure that
URBs are given back in order of submission, whenever a TD is added to
the done list, all the preceding TDs for the same endpoint must be
added as well (going back to the first one that isn't already on the
done list).
The done list manipulations must all be protected by the private
lock. The scope of the lock is expanded in preparation for the
watchdog routine to be added in a later patch.
We have to be more careful about giving back unlinked URBs. Since TDs
may be added to the done list by the watchdog routine and not in
response to a controller interrupt, we have to check explicitly to
make sure all the URB's TDs that were added to the done list have been
processed before giving back the URB.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an URB is unlinked from a dead controller, ohci-hcd gives back
the URB with no regard for cleaning up the internal data structures.
This won't play nicely with the upcoming changes to the TD done
list.
Therefore make ohci_urb_dequeue() call finish_unlinks(), which uses
td_done() to do a proper cleanup, rather than calling finish_urb()
directly. Also, remove the checks that urb_priv is non-NULL; the
driver guarantees that urb_priv will never be NULL for a valid URB.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts the important parts of commit 89a0fd18a9 (USB:
OHCI handles more ZFMicro quirks), namely, the parts related to
handling orphan TDs for interrupt endpoints. A later patch in this
series will introduce a more general mechanism that applies to all
endpoint types and all controllers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Problem Summary: Problem has been observed generally with PM states
where VBUS goes off during suspend. There are some SS USB devices which
take longer time for link training compared to many others. Such
devices fail to reconnect with same old address which was associated
with it before suspend.
When system resumes, at some point of time (dpm_run_callback->
usb_dev_resume->usb_resume->usb_resume_both->usb_resume_device->
usb_port_resume) SW reads hub status. If device is present,
then it finishes port resume and re-enumerates device with same
address. If device is not present then, SW thinks that device was
removed during suspend and therefore does logical disconnection
and removes all the resource allocated for this device.
Now, if I put sufficient delay just before root hub status read in
usb_resume_device then, SW sees always that device is present. In normal
course(without any delay) SW sees that no device is present and then SW
removes all resource associated with the device at this port. In the
latter case, after sometime, device says that hey I am here, now host
enumerates it, but with new address.
Problem had been reproduced when I connect verbatim USB3.0 hard disc
with my STiH407 XHCI host running with 3.10 kernel.
I see that similar problem has been reported here.
https://bugzilla.kernel.org/show_bug.cgi?id=53211
Reading above it seems that bug was not in 3.6.6 and was present in 3.8
and again it was not present for some in 3.12.6, while it was present
for few others. I tested with 3.13-FC19 running at i686 desktop, problem
was still there. However, I was failed to reproduce it with 3.16-RC4
running at same i686 machine. I would say it is just a random
observation. Problem for few devices is always there, as I am unable to
find a proper fix for the issue.
So, now question is what should be the amount of delay so that host is
always able to recognize suspended device after resume.
XHCI specs 4.19.4 says that when Link training is successful, port sets
CSC bit to 1. So if SW reads port status before successful link
training, then it will not find device to be present. USB Analyzer log
with such buggy devices show that in some cases device switch on the
RX termination after long delay of host enabling the VBUS. In few other
cases it has been seen that device fails to negotiate link training in
first attempt. It has been reported till now that few devices take as
long as 2000 ms to train the link after host enabling its VBUS and
RX termination. This patch implements a 2000 ms timeout for CSC bit to set
ie for link training. If in a case link trains before timeout, loop will
exit earlier.
This patch implements above delay, but only for SS device and when
persist is enabled.
So, for the good device overhead is almost none. While for the bad
devices penalty could be the time which it take for link training.
But, If a device was connected before suspend, and was removed
while system was asleep, then the penalty would be the timeout ie
2000 ms.
Results:
Verbatim USB SS hard disk connected with STiH407 USB host running 3.10
Kernel resumes in 461 msecs without this patch, but hard disk is
assigned a new device address. Same system resumes in 790 msecs with
this patch, but with old device address.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I am removing two fix mes in this file as after dicussing then it seems
there is no reason to check against Null for usb_device as it can never
be NULL and this is check is therefore not needed.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some laptops have an internal port for a BT device which picks
up noise when the kill switch is used, but not enough to trigger
printk_rlimit(). So we shouldn't log consecutive faults of this kind.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When radio is off bit GPIO3_INTMD should be on and off when radio is on.
Add these to the tail of vnt_radio_power_off and vnt_radio_power_on
and remove variable bHWRadioOff.
In device_init_registers just check GPIO3_DATA are in correct state and
always power on.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the checkpatch.pl --strict issues:
CHECK: Please use a blank line after function/struct/union/enum declarations
CHECK: Alignment should match open parenthesis
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the checkpatch.pl --strict issues:
CHECK: braces {} should be used on all arms of this statement
CHECK: Alignment should match open parenthesis
CHECK: Prefer kzalloc(sizeof(*dev)...) over kzalloc(sizeof(struct comedi_device)...)
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the checkpatch.pl --strict issues:
CHECK: Please use a blank line after function/struct/union/enum declarations
For aesthetics, convert the inline functions into simple macros.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the checkpatch.pl --strict issues:
CHECK: DEFINE_MUTEX definition without comment
CHECK: braces {} should be used on all arms of this statement
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The (*attach) of driver calls this function to probe the 'id' of the
hardware to verify that a valid boardinfo has been selected by the
user.
The dev_dbg() messages when the boardinfo is valid is just added
noise. The printk messages when the id does not match the boardinfo
does have some value.
Refactor the function to remove the noise and use a common message
for the "(probed, not recommended)" message.
Convert the printk() messages to dev_err().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All cases of the switch call ni_mseries_get_pll_parameters() with the same
parameters. Move the call out of the switch.
Also, move the printk from ni_mseries_get_pll_parameters() so that it can
be converted into a dev_err().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need to wake up regular worker when nr_running==1,
so need_more_worker() is sufficient here.
And need_more_worker() gives us better readability due to the name of
"keep_working()" implies the rescuer should keep working now but
the rescuer is actually leaving.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support of the Promise FastTrak TX8660 SATA HBA in ahci mode by
registering the board in the ahci_pci_tbl[].
Note: this HBA also provide a hardware RAID mode when activated in
BIOS but specific drivers from the manufacturer are required in this
case.
Signed-off-by: Romain Degez <romain.degez@gmail.com>
Tested-by: Romain Degez <romain.degez@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This adds support for the integrated AHCI-compliant Serial ATA
controller present on the NVIDIA Tegra124 system-on-chip.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Tegra124 SATA controller requires 4 clocks. Increase this constant
to be able to use them all.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds device tree binding documentation for the SATA
controller found on NVIDIA Tegra SoCs.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
arch/arm/mach-kirkwood has been removed, since kirkwood is now
supported by arch/arm/mach-mvebu. Remove it from the MAINTAINERS file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>