Instance of this IP on Qualcomm's SOCs has bit different layout for datactrl
register. Bit position datactrl[16:4] hold the true block size instead of power
of 2.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Qcom SD Card controller POWER, CLKCTRL, DATACTRL and COMMAND registers
should be updated in MCLK domain, and writes to these registers must be
separated by three MCLK cycles. This resitriction is not applicable for
other registers. Any subsequent writes to these register will be ignored
until 3 MCLK have passed.
One usec delay between two CMD register writes is not sufficient in the
card identification phase where the CCLK is very low. This patch replaces
a static 1 usec delay to use mmci_reg_delay function which can provide
correct delay depending on the cclk frequency.
Without this patch the card is not detected.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a Qualcomm SD Card controller specific register variations
to header file. Qualcomm SDCC controller is pl180, with slight changes in
the register layout from standard pl180 register set.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mach-omap2 directory contains full register defines for OMAP4
control module but only around 27 of those are used. There are is
a total of 1795 register defines in four files with only 27 in use.
That is pretty low usefulness ratio...
I guess alot more was used when we had omap4 board files and
mach-omap2 contained more drivers but this has now changed.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch is based on feedback from Viresh Kumar.
Since cpufreq-cpu0 driver has already check opp table, there is no
need to same check in mach-shmobile.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car Gen 2 PCIe driver provides PCIe host support for
Renesas R-Car Gen2 platforms. To increase hardware support enable
the driver in the shmobile_defconfig multiplatform configuration.
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the sound subsystem driver for Odroid-X2 and
Odroid-U3 boards. The codec works in I2S master mode; there
are two separate audio routing paths defined, as there are
differences in the signal routing between the X2 and U3 boards,
i.e. U3 uses single jack for headphones and microphone.
Signed-off-by: Chen Zhen <zhen1.chen@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As early printk is not supported when devices are initialised
using DT, so remove it from the command line.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As early printk is not supported when devices are initialised
using DT, so remove it from the command line.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
By just using GCC's array initialization extension, we
can easily drop order dependency between tps65218_regulattors
enumeration and tps65218_pmic_regs array.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
volt table is always NULL for all regulators,
might as well drop the argument.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The second range of this particular regulator,
starts at 1.60V, not as 1.55V as it was originally
implied by code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The Authenticated Payload Timeout Expired event is valid for
controllers with BR/EDR Secure Connections support, but also for
LE only controllers supporting LE Ping feature. When either of them
is available enable this event. Previous it was not enabled when
the controller was only supporting LE operation.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Using the sgtl5000 codec driver as a module and trying to remove it causes the
followig kernel oops:
root@freescale /$ rmmod snd-soc-imx-sgtl5000
[ 117.122920] ------------[ cut here ]------------
[ 117.127609] WARNING: CPU: 0 PID: 631 at drivers/regulator/core.c:3604 regula)
[ 117.137046] Modules linked in: snd_soc_imx_sgtl5000(-) snd_soc_sgtl5000 evbug
[ 117.144315] CPU: 0 PID: 631 Comm: rmmod Not tainted 3.16.0-rc3-next-201407043
[ 117.153366] Backtrace:
[ 117.155865] [<80011e5c>] (dump_backtrace) from [<80011ff8>] (show_stack+0x18)
[ 117.163484] r6:802fcc48 r5:00000000 r4:00000000 r3:00000000
[ 117.169228] [<80011fe0>] (show_stack) from [<80668cc0>] (dump_stack+0x88/0xa)
[ 117.176508] [<80668c38>] (dump_stack) from [<80029a38>] (warn_slowpath_commo)
[ 117.184696] r5:00000009 r4:00000000
[ 117.188322] [<800299c8>] (warn_slowpath_common) from [<80029a80>] (warn_slow)
[ 117.197150] r8:dd60d600 r7:ddfa6d00 r6:dd5d9064 r5:dd5e0f90 r4:dd5d9400
[ 117.203983] [<80029a5c>] (warn_slowpath_null) from [<802fcc48>] (regulator_u)
[ 117.212828] [<802fcb74>] (regulator_unregister) from [<7f0047c4>] (ldo_regul)
[ 117.223475] r4:dd59e300 r3:dd5e0f90
[ 117.227100] [<7f00479c>] (ldo_regulator_remove [snd_soc_sgtl5000]) from [<7f)
[ 117.238959] r4:dd5d8000 r3:ddd51420
[ 117.242623] [<7f0047dc>] (sgtl5000_remove [snd_soc_sgtl5000]) from [<804e5b1)
[ 117.252489] r5:00000000 r4:dd5d8000
[ 117.256111] [<804e5af8>] (soc_remove_codec) from [<804e5ed4>] (soc_remove_da)
[ 117.264933] r4:ddfb640c r3:00000000
[ 117.268555] [<804e5c10>] (soc_remove_dai_links) from [<804e5fbc>] (snd_soc_u)
[ 117.277810] r10:80359e48 r9:dd684000 r8:dd5ca800 r7:dd685e60 r6:00000001 r5c
[ 117.285761] r4:dd5d9064
[ 117.288329] [<804e5f28>] (snd_soc_unregister_card) from [<804f29f0>] (devm_c)
[ 117.297324] r6:00000004 r5:ddd0fc10 r4:dd5a7980 r3:804f29dc
[ 117.303095] [<804f29dc>] (devm_card_release) from [<8035a418>] (release_node)
[ 117.311369] [<8035a2a8>] (release_nodes) from [<8035aab4>] (devres_release_a)
[ 117.319583] r10:00000000 r9:dd684000 r8:8000ed64 r7:00000081 r6:ddd0fc44 r54
[ 117.327543] r4:ddd0fc10
[ 117.330108] [<8035aa7c>] (devres_release_all) from [<803571c8>] (__device_re)
[ 117.339214] r4:ddd0fc10 r3:dd5d9010
[ 117.342989] [<80357148>] (__device_release_driver) from [<80357a48>] (driver)
[ 117.351607] r5:7f00c9e4 r4:ddd0fc10
[ 117.355285] [<8035798c>] (driver_detach) from [<80357030>] (bus_remove_drive)
[ 117.363454] r6:00000880 r5:00000000 r4:7f00c9e4 r3:dd6c3a80
[ 117.369195] [<80356fdc>] (bus_remove_driver) from [<803580b8>] (driver_unreg)
[ 117.377683] r4:7f00c9e4 r3:dd60d480
[ 117.381305] [<80358088>] (driver_unregister) from [<80358bb4>] (platform_dri)
[ 117.390642] r4:7f00ca28 r3:7f00c35c
[ 117.394309] [<80358ba0>] (platform_driver_unregister) from [<7f00c370>] (imx)
[ 117.406188] [<7f00c35c>] (imx_sgtl5000_driver_exit [snd_soc_imx_sgtl5000]) f)
[ 117.417452] [<8008c2b8>] (SyS_delete_module) from [<8000eba0>] (ret_fast_sys)
[ 117.425753] r6:5f636f73 r5:5f646e73 r4:00016f40
[ 117.430428] ---[ end trace 8fd8a5cb39e46d0e ]---
This problem is well explained by Russell King:
"The sgtl5000 uses a two-stage initialisation process. The first stage
is when the platform driver is probed, where some resources are found
and initialised. The second stage is via the codec driver's probe
function, where regulators are found and initialised using the managed
resource support.
The problem here is that this works fine until the codec driver is
unbound. When this occurs, sgtl5000_remove() is called which is a no-op
as far as the managed resource code is concerned. The regulators remain
allocated, and their pointers in sgtl5000_priv remain valid.
If the codec is now re-probed, it will again try and find the regulators,
which will now be busy. This will fail.
That's not the only problem - if using the LDO regulator, the regulator
is unregistered from the regulator core code, but it still has a user.
When the user is cleaned up (eg, by removing the module) it hits the
free'd regulator, and this can oops the kernel.
This bug was originally introduced by 63e54cd9ca ("ASoC: sgtl5000:
Use devm_regulator_bulk_get()")."
This reverts commit 63e54cd9ca.
Tested on a imx53-qsb board.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_of_parse_card_name() may be called before card->dev has been
set, which results in a kernel panic.
Unable to handle kernel NULL pointer dereference at virtual address 00000210
PC is at snd_soc_of_parse_card_name+0x18/0x54
LR is at snow_probe+0x5c/0xd4
Add an error check in snd_soc_of_parse_card_name() to take care of this
case and print out a message in case of error.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The panel power sequencer on vlv doesn't appear to accept changes to its
T12 power down duration during warm reboots. This change forces a delay
for warm reboots to the T12 panel timing as defined in the VBT table for
the connected panel.
Ver2: removed redundant pr_crit(), commented magic value for pp_div_reg
Ver3: moved SYS_RESTART check earlier, new name for pp_div.
Ver4: Minor issue changes
Ver5: Move registration of reboot notifier to edp_connector_init,
Added warning comment to handler about lack of PM notification.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The console subsystem only provides a function to switch to a given
console, but we want to actually only switach away from vgacon.
Unconditionally switching to the dummy console resulted in switching
away from fbcon in multi-gpu setups when other gpu drivers are loaded
before i915.
Then either the reinitialization of fbcon when i915 registers its
fbdev emulation or the teardown of the fbcon driver killed the
machine. So only switch to the dummy console when it's required.
Kudos to Chris for the original idea, I've only refined it a bit to
still unregister vgacon even when it's currently unused.
This regression has been introduced in
commit a4de05268e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jun 5 16:20:46 2014 +0200
drm/i915: Kick out vga console
Reported-and-tested-by: Ed Tomlinson <edt@aei.ca>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should keep DEVICE_READY bit set in the ULPS enter sequence. In
exit sequence also we should set DEVICE_READY, but thats causing
blankout for me. Also exit sequence is simplified as per hw team
recommendation.
This should fix -
[drm:intel_dsi_clear_device_ready] *ERROR* DSI LP not going Low
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80818
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
While sending DPI SHUTDOWN command, we cannot wait for FIFO empty as
pipes are not disabled at that time. In case of MIPI we disable port
first and send SHUTDOWN command while pipe is still running and FIFOs
will not be empty, causing spurious error log
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add driver for i2s controller found on rk3066, rk3168 and rk3288
processors from rockchip.
Tested on the RK3288 SDK board.
Signed-off-by: Jianqun Xu <xjq@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add devicetree bindings for i2s controller found on
rk3066, rk3188 and rk3288 processors from rockchip.
Signed-off-by: Jianqun Xu <xjq@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
phy_suspend and phy_resume are two commonly used helper functions that
need to be exported for Ethernet drivers to be built as modules
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
Freescale ethernet driver updates (part 3)
Here's the third batch of patches for the Freescale FEC ethernet driver,
based upon the previous set of patches. This concludes the changes I
currently have prepared and have been reviewed for the next merge window
at this time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both transmit and receive use the same infrastructure for calculating
the packet timestamp. Rather than duplicating the code, provide a
function to do this common work. Model this function in the Intel
e1000e version which avoids calling ns_to_ktime() within the spinlock;
the spinlock is critical for timecounter_cyc2time() but not
ns_to_ktime().
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a useless status check in the transmit reap path - we have
already checked that the BD_ENET_TX_READY bit is clear, and as the
hardware only ever clears this bit, there is no way this test can ever
be true.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we timeout on transmit, it would be useful to dump the transmit
ring, so we can see the ring state. This can be helpful to diagnose
the cause of transmit timeouts.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear any pending receive interrupt before we process a pending packet.
This helps to avoid any spurious interrupts being raised after we have
fully cleaned the receive ring, while still allowing an interrupt to be
raised if we receive another packet.
The position of this is critical: we must do this prior to reading the
next packet status to avoid potentially dropping an interrupt when a
packet is still pending.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of "better implementation of iMX6 ERR006358 quirk", we no longer have
a requirement for a delayed work. Moreover, the work is now only used
for timeout purposes, so the timeout flag is also pointless - we set it
each time we queue the work, and the work clears it.
Replace the fec_enet_delayed_work struct with a standard work_struct,
resulting in simplified timeout handling code.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a (delayed) workqueue for ERR006358 is not correct - a work queue
is a single-trigger device. Once the work queue has been scheduled, it
can't be re-scheduled until it has been run. This can cause problems -
with an appropriate packet timing, we can end up with packets queued,
but not sent by the hardware, resulting in the transmit timeout firing.
Re-implement this as per the workaround detailed in the ERR006358
documentation - if there are packets waiting to be sent when we service
the transmit ring, and we see that the transmitter is not running,
kick the transmitter to run the pending entries in the ring.
Testing here with a 10Mbit half duplex link sees the resulting iperf
TCP bandwidth increase from between 1 to 2Mbps to between 8 to 9Mbps.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes the command value generated for CSUM calculation
when running in big endian mode. The Ethernet protocol ID for IP was
being unconditionally byte-swapped in the layer 3 protocol check (with
swab16), which caused the mvneta driver to not function correctly in
big endian mode. This patch byte-swaps the ID conditionally with
htons.
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a bonding master reclaims the netpoll info struct, slaves could
still hold a pointer to the reclaimed data. This patch fixes it: as
soon as netpoll_async_cleanup is called for a slave (eg. when
un-enslaved), we make sure that this slave doesn't point to the data.
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds debugfs capabilities to netback. There used to be a similar
patch floating around for classic kernel, but it used procfs. It is based on a
very similar blkback patch.
It creates xen-netback/[vifname]/io_ring_q[queueno] files, reading them output
various ring variables etc. Writing "kick" into it imitates an interrupt
happened, it can be useful to check whether the ring is just stalled due to a
missed interrupt.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cb1ce2ef38 ("ipv6: Implement automatic flow label generation
on transmit") introduced ip6_make_flowlabel, while commit b73c3d0e4f
("net: Save TX flow hash in sock and set in skbuf on xmit") introduced
ip6_set_txhash.
ip6_set_tx_hash() uses sk_v6_daddr which references
__sk_common.skc_v6_daddr from struct sock_common, which is gated with
IS_ENABLED(CONFIG_IPV6).
ip6_make_flowlabel() uses the ipv6 member from struct net which is
also gated with IS_ENABLED(CONFIG_IPV6).
When CONFIG_IPV6 is disabled, we will hit a build failure that looks
like this when the compiler attempts inlining these functions:
CC [M] drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.o
In file included from include/net/inet_sock.h:27:0,
from include/net/ip.h:30,
from drivers/net/ethernet/broadcom/cnic.c:37:
include/net/ipv6.h: In function 'ip6_set_txhash':
include/net/sock.h:327:33: error: 'struct sock_common' has no member named 'skc_v6_daddr'
#define sk_v6_daddr __sk_common.skc_v6_daddr
^
include/net/ipv6.h:696:49: note: in expansion of macro 'sk_v6_daddr'
keys.dst = (__force __be32)ipv6_addr_hash(&sk->sk_v6_daddr);
^
In file included from include/net/inetpeer.h:15:0,
from include/net/route.h:28,
from include/net/ip.h:31,
from drivers/net/ethernet/broadcom/cnic.c:37:
include/net/ipv6.h: In function 'ip6_make_flowlabel':
include/net/ipv6.h:706:37: error: 'struct net' has no member named 'ipv6'
if (!flowlabel && (autolabel || net->ipv6.sysctl.auto_flowlabels)) {
^
Fixes: cb1ce2ef38 ("ipv6: Implement automatic flow label generation on transmit")
Fixes: b73c3d0e4f ("net: Save TX flow hash in sock and set in skbuf on xmit")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
Freescale ethernet driver updates (part 2)
Here's the second batch of patches for the Freescale FEC ethernet driver,
based upon the previous set of patches. One further set of 7 patches
remains.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Many places call fec_restart() with the second parameter being some kind
of previously saved duplex value, but only two places call it with some
other setting. This is at odds with how the other link settings are
handled, and used to be racy before the rtnl locks were added to
fec_restart()'s various call paths.
Clean this up so all link capabilities are handled in the same way -
saved into the fec_enet_private structure, and then fec_restart() acts
on those settings.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>