The CurrentEL system register reports the Current Exception Level
of the CPU. It doesn't say anything about the stack handling, and
yet we compare it to PSR_MODE_EL2t and PSR_MODE_EL2h.
It works by chance because PSR_MODE_EL2t happens to match the right
bits, but that's otherwise a very bad idea. Just check for the EL
value instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[catalin.marinas@arm.com: fixed arch/arm64/kernel/efi-entry.S]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reading the controller configuration information is a valid management
command when the controller is unconfigured. Allow this command, but
return invalid index on all other commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Broadcom USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Intel USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a Bluetooth controller does not have a valid public Bluetooth
address, then allow the driver to indicate this. If the quirk is
set, the Bluetooth core will switch to unconfigured state first
and will allow userspace to configure the address before starting
the full initialization of the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current existing device quirks are not documented. So instead of
spreading bits and pieces somewhere in the code, add proper comments
on where these quirks can be used and what behavior they change.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since cd9151e26d (xen/balloon: set a
mapping for ballooned out pages), a ballooned out page had its entry
in the p2m set to the MFN of one of the scratch pages. This means
that the p2m will contain many entries pointing to the same MFN.
During a domain save, these many-to-one entries are not identified as
such and the scratch page is saved multiple times. On restore the
ballooned pages are populated with new frames and the domain may use
up its allocation before all pages can be restored.
Since the original fix only needed to keep a mapping for the ballooned
page it is safe to set ballooned out pages as INVALID_P2M_ENTRY in the
p2m (as they were before). Thus preventing them from being saved and
re-populated on restore.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Marek Marczykowski <marmarek@invisiblethingslab.com>
Tested-by: Marek Marczykowski <marmarek@invisiblethingslab.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: <stable@vger.kernel.org>
This patch removes the build-time test that ensures at least one RNG
is set. Instead we will simply not build drbg if no options are set
through Kconfig.
This also fixes a typo in the name of the Kconfig option CRYTPO_DRBG
(should be CRYPTO_DRBG).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Control module related PM initializations are now moved within control
module driver. Done in preparation to isolate the code to its own driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
It's wasteful to use list_del_init (which re-initializes the list_head)
if we're just about to free the element and never use it again.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a found device is marked as blocked while doing passive LE scanning,
neither report it nor try to connect to it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The __sync_icache_dcache routine will only flush the dcache for the
first page of a compound page, potentially leading to stale icache
data residing further on in a hugetlb page.
This patch addresses this issue by taking into consideration the
order of the page when flushing the dcache.
Reported-by: Mark Brown <broonie@linaro.org>
Tested-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org> # v3.11+
The define ARM64_64K_PAGES is tested for rather than
CONFIG_ARM64_64K_PAGES. Correct that typo here.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The SM_SCLK_SM_SCLK is define is cut and pasted twice. I have removed
the second define.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
The DRBG-style linked list to manage input data that is fed into the
cipher invocations is replaced with the kernel linked list
implementation.
The change is transparent to users of the interfaces offered by the
DRBG. Therefore, no changes to the testmgr code is needed.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit c2e28dc9 (kbuild: Print the name of the build directory) prints
the name of the build directory for O= builds, but we should not be
doing this in make -s mode, so that commands like
make -s O=<dir> kernelrelease
can be used by scripts. This matches the behavior of make itself, where
the -s option implies --no-print-directory.
Signed-off-by: Michal Marek <mmarek@suse.cz>
This is already done automatically for many other ARM platforms by the
ARM core code, but since pxa is using the .map_io callback, it needs to
call it explicitely for earlyprintk support.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
If somebody attempts to check the capability of an IOMMU domain prior to
device attach, then we'll try to dereference a NULL SMMU pointer through
the SMMU domain (since we can't determine the actual SMMU instance until
we have a device attached).
This patch fixes the capability check so that non-global features are
reported as being absent when no device is attached to the domain.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The public address configuration option is value 0x02 since the generic
external configuration is value 0x01. So adjust this accordingly and
also add the value 0x01 to the list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
AMD-Vi support for IOMMU sysfs. This allows us to associate devices
with a specific IOMMU device and examine the capabilities and features
of that IOMMU. The AMD IOMMU is hosted on and actual PCI device, so
we make that device the parent for the IOMMU class device. This
initial implementaiton exposes only the capability header and extended
features register for the IOMMU.
# find /sys | grep ivhd
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/devices
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/devices/0000:00:00.0
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/devices/0000:00:02.0
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/devices/0000:00:04.0
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/devices/0000:00:09.0
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/devices/0000:00:11.0
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/devices/0000:00:12.0
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/devices/0000:00:12.2
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/devices/0000:00:13.0
...
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/power
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/power/control
...
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/device
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/subsystem
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/amd-iommu
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/amd-iommu/cap
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/amd-iommu/features
/sys/devices/pci0000:00/0000:00:00.2/iommu/ivhd0/uevent
/sys/class/iommu/ivhd0
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Register our DRHD IOMMUs, cross link devices, and provide a base set
of attributes for the IOMMU. Note that IRQ remapping support parses
the DMAR table very early in boot, well before the iommu_class can
reasonably be setup, so our registration is split between
intel_iommu_init(), which occurs later, and alloc_iommu(), which
typically occurs much earlier, but may happen at any time later
with IOMMU hot-add support.
On a typical desktop system, this provides the following (pruned):
$ find /sys | grep dmar
/sys/devices/virtual/iommu/dmar0
/sys/devices/virtual/iommu/dmar0/devices
/sys/devices/virtual/iommu/dmar0/devices/0000:00:02.0
/sys/devices/virtual/iommu/dmar0/intel-iommu
/sys/devices/virtual/iommu/dmar0/intel-iommu/cap
/sys/devices/virtual/iommu/dmar0/intel-iommu/ecap
/sys/devices/virtual/iommu/dmar0/intel-iommu/address
/sys/devices/virtual/iommu/dmar0/intel-iommu/version
/sys/devices/virtual/iommu/dmar1
/sys/devices/virtual/iommu/dmar1/devices
/sys/devices/virtual/iommu/dmar1/devices/0000:00:00.0
/sys/devices/virtual/iommu/dmar1/devices/0000:00:01.0
/sys/devices/virtual/iommu/dmar1/devices/0000:00:16.0
/sys/devices/virtual/iommu/dmar1/devices/0000:00:1a.0
/sys/devices/virtual/iommu/dmar1/devices/0000:00:1b.0
/sys/devices/virtual/iommu/dmar1/devices/0000:00:1c.0
...
/sys/devices/virtual/iommu/dmar1/intel-iommu
/sys/devices/virtual/iommu/dmar1/intel-iommu/cap
/sys/devices/virtual/iommu/dmar1/intel-iommu/ecap
/sys/devices/virtual/iommu/dmar1/intel-iommu/address
/sys/devices/virtual/iommu/dmar1/intel-iommu/version
/sys/class/iommu/dmar0
/sys/class/iommu/dmar1
(devices also link back to the dmar units)
This makes address, version, capabilities, and extended capabilities
available, just like printed on boot. I've tried not to duplicate
data that can be found in the DMAR table, with the exception of the
address, which provides an easy way to associate the sysfs device with
a DRHD entry in the DMAR. It's tempting to add scopes and RMRR data
here, but the full DMAR table is already exposed under /sys/firmware/
and therefore already provides a way for userspace to learn such
details.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
IOMMUs currently have no common representation to userspace, most
seem to have no representation at all aside from a few printks
on bootup. There are however features of IOMMUs that are useful
to know about. For instance the IOMMU might support superpages,
making use of processor large/huge pages more important in a device
assignment scenario. It's also useful to create cross links between
devices and IOMMU hardware units, so that users might be able to
load balance their devices to avoid thrashing a single hardware unit.
This patch adds a device create and destroy interface as well as
device linking, making it very lightweight for an IOMMU driver to add
basic support. IOMMU drivers can provide additional attributes
automatically by using an attribute_group.
The attributes exposed are expected to be relatively device specific,
the means to retrieve them certainly are, so there are currently no
common attributes for the new class created here.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
VT-d code currently makes use of pci_find_upstream_pcie_bridge() in
order to find the topology based alias of a device. This function has
a few problems. First, it doesn't check the entire alias path of the
device to the root bus, therefore if a PCIe device is masked upstream,
the wrong result is produced. Also, it's known to get confused and
give up when it crosses a bridge from a conventional PCI bus to a PCIe
bus that lacks a PCIe capability. The PCI-core provided DMA alias
support solves both of these problems and additionally adds support
for DMA function quirks allowing VT-d to work with devices like
Marvell and Ricoh with known broken requester IDs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The IOMMU code now provides a common interface for finding or
creating an IOMMU group for a device on PCI buses. Make use of it
and remove piles of code.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The common iommu_group_get_for_dev() allows us to greatly simplify
our group lookup for a new device. Also, since we insert IVRS
aliases into the PCI DMA alias quirks, we should alway come up with
the same results as the existing code.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
AMD-Vi already has a concept of an alias provided via the IVRS table.
Now that PCI-core also understands aliases, we need to incorporate
both aspects when programming the IOMMU. IVRS is generally quite
reliable, so we continue to prefer it when an alias is present. For
cases where we have an IVRS alias that does not match the PCI alias
or where PCI does not report an alias, report the mismatch to allow
us to collect more quirks and dynamically incorporate the alias into
the device alias quirks where possible.
This should allow AMD-Vi to work with devices like Marvell and Ricoh
with DMA function alias quirks unknown to the BIOS.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Currently each IOMMU driver that supports IOMMU groups has its own
code for discovering the base device used in grouping. This code
is generally not specific to the IOMMU hardware, but to the bus of
the devices managed by the IOMMU. We can therefore create a common
interface for supporting devices on different buses.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Contrary to the host-backed shader interface that has a per-context
name-space for shaders, the compat shader namespace was per client
(or rather, per file). Fix this so that the compat shader namespace is per
context, and at the same time, make command buffer managed context resource
management generic.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>