The clock control unit on the A23 is similar to the one found on the A31.
The AHB1, APB1, APB2 gates on the A23 are almost identical to the ones
on the A31, but some outputs are missing.
The main CPU PLL (PLL1) however is like that on older Allwinner SoCs,
such as the A10 or A20, but the N factor starts from 1 instead of 0.
This patch adds support for PLL1 and all the basic clock muxes and gates.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A few of the clock modules have odd dividers, such as
the 2 lowest dividers being the same (2), or have the
same divider when the highest bit is set.
This patch adds support for optional divider tables,
so the clock framework will know about the odd values.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PLLs on newer Allwinner SoC's, such as the A31 and A23, have a
N multiplier factor that starts from 1, not 0.
This patch adds an option to the factor clk driver's config data
structures to specify the base value of N.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With sunxi_gates clocks registered with clkdev, we can use the
protected clocks list to enable the "ahb_sdram" clock, instead
of looking for it and adding CLK_IGNORE_UNUSED inline in the
clock setup code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have support for sun8i specific clocks in the driver,
add the corresponding clock nodes to the DTSI. Also update the
existing peripherals with the correct clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Instead of looking through the entire list of entries we can more
efficiently use the new hci_pend_le_action_lookup() function to look up
entries specifically in the pend_le_reports list. Since the search is
now limited to the right list we can also remove an unnecessary check
for list_empty() before the lookup.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances we need to look up entries in pend_le_conns and in
other in pend_le_reports. This patch converts the existing lookup
function for pend_le_conns to something that can be used for both lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since there are no more users of this function we can simply go ahead
and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is the last place using hci_pend_le_conn_add() and we can more
just as simply manipulate the list directly here.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When powering off (hci_dev_do_close) we should clear both the
pend_le_reports and pend_le_conns types of entries. When powering on
respectively we should populate both lists. This patch converts the
hci_pend_le_conns_clear() function into hci_pend_le_actions_clear()
(which can now be static) and converts the restart_le_auto_conns()
function into restart_le_actions().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there are no-longer any users of the hci_pend_le_conn_del()
function we can simply go ahead and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since params->action is used for both the pend_le_conns and
pend_le_reports lists we can simplify the adding and deleting of the
lists considerably. For example, when deleting entries in most
situations we no-longer need to check the auto_connect value but can
directly proceed with calling list_del_init on param->action (which is
safe even if the entry is not part of any list).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hci_conn_params_set() is called if the new auto_connect value is
the same as the old one we don't need to take any action. Simply return
success from the function in this case.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that pend_le_connections is a list of hci_conn_params entries we can
simply remove items from that list as we iterate through the global list
of le_conn_params. This also moves the responsibility of calling
hci_update_background_scan() to the functions that were previously
calling hci_pend_le_conns_clear(). The only user that's left for
hci_pend_le_conns_clear() is hci_dev_do_close() which anyway does not
need to call hci_update_background_scan().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To simplify manipulation and lookup of hci_conn_params entries of the
type HCI_AUTO_CONN_REPORT it makes sense to store them in their own
list. The new action list_head in hci_conn_params is used for this
purpose.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation to store also HCI_AUTO_CONN_REPORT entries in a list it
makes sense to convert the existing pend_le_conn list head of
hci_conn_params into a more generically named "action". This makes sense
because a parameter entry will never participate in more than one action
list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we're doing passive scanning we shouldn't proceed with any of the
code that deals with active scanning (pending reports, etc.). This patch
fixes a missing return statement for the passive scanning section in the
process_adv_report() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
suppress compiler warnings:
drivers/iommu/intel-iommu.c: In function ‘device_to_iommu’:
drivers/iommu/intel-iommu.c:673: warning: ‘segment’ may be used uninitialized in this function
drivers/iommu/intel-iommu.c: In function ‘get_domain_for_dev.clone.3’:
drivers/iommu/intel-iommu.c:2217: warning: ‘bridge_bus’ may be used uninitialized in this function
drivers/iommu/intel-iommu.c:2217: warning: ‘bridge_devfn’ may be used uninitialized in this function
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use inline function dma_pte_superpage() instead of macro for
better readability.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Alloc_domain() will initialize domain->nid to -1. So the
initialization for domain->nid in md_domain_init() is redundant,
clear it.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
__dmar_enable_qi() will initialize free_head,free_tail and
free_cnt for q_inval. Remove the redundant initialization
in dmar_enable_qi().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use list_for_each_entry_safe() instead of list_entry()
to simplify code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Make the omapdrm driver use the new HDMI ops when possible.
omapdrm will call set_hdmi_mode (when available) to tell the encoder
driver whether the monitor is a DVI or HDMI monitor, and if it's an HDMI
monitor, omapdrm will call set_hdmi_infoframe to to set the AVI
infoframe.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
We no longer need the horrible driver internal videmode tables, which
were used to decide if a given videomode is a HDMI or DVI mode. So
remove all related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using hardcoded AVI infoframe, and a custom HDMI/DVI mode
selection based in internal videomode tables, add support to set the
infoframe and HDMI/DVI mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using hardcoded AVI infoframe, and a custom HDMI/DVI mode
selection based in internal videomode tables, add support to set the
infoframe and HDMI/DVI mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add infoframe and hdmi_dvi_mode fields to 'struct hdmi_config' which
will be used in the following patches for OMAP4 and OMAP5 HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add pass-through functions for set_infoframe and set_hdmi_mode to
hdmi-connector and tpd12s015 drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add two new ops for HDMI: set_infoframe() and set_hdmi_mode(). The first
one can be used to specify the infoframe that should be sent to the HDMI
monitor, and the second one is used to enable HDMI mode (versus DVI
mode).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We now use the common AVI infoframe support, so the OMAP specific AVI
infoframe code can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using OMAP specific AVI infoframe structs, use the common one
from include/linux/hdmi.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using OMAP specific AVI infoframe structs, use the common one
from include/linux/hdmi.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP HDMI driver has an 'enum hdmi_audio_sample_size', which conflicts
with the common include/linux/hdmi.h.
Change the name of the OMAP specific enum with '_omap" postfix.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_timings_ok() is a bit confusing how it handles the return
value.
Change the function to just return immediately when a timing is deemed
not valid, making the code much easier to follow.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP2/3 does not support interlace for LCD out. OMAP4+ does, but is not
supported by the driver at the moment.
The driver still accepts interlaced mode for LCD out, causing broken
display output.
This patch makes dispc reject interlace for LCD out.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch fixes building CLPS711X FB driver if the framebuffer
core is used as a module.
LD init/built-in.o
drivers/built-in.o: In function `clps711x_fb_remove':
:(.text+0x44a8): undefined reference to `unregister_framebuffer'
drivers/built-in.o: In function `clps711x_fb_probe':
:(.text+0x44cc): undefined reference to `fb_get_options'
:(.text+0x45d8): undefined reference to `fb_alloc_cmap'
:(.text+0x45e4): undefined reference to `register_framebuffer'
make: *** [vmlinux] Error 1
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This small patch completes #defines for Control/Status Register,
adds comments for the missing ones there and on the Interrupt Mask
Register and additionally corrects "#define ICE1712_SERR_LEVEL 0x04 -> 0x08",
according to documentation.
Signed-off-by: Konstantinos Tsimpoukas <kostaslinuxxx@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Read Controller Configuration Information command allows retrieving
details about possible configurations option. The supported options are
returned and also the missing options (if any).
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For HSW/BDW display HD-A controller, hda_set_bclk() is defined to set BCLK
by programming the M/N values as per the core display clock (CDCLK) queried from
i915 display driver.
And the audio driver will also set BCLK in azx_first_init() since the display
driver can turn off the shared power in boot phase if only eDP is connected
and M/N values will be lost and must be reprogrammed.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Haswell and Broadwell, if the display power well has been disabled,
the display audio controller divider values EM4 M VALUE and EM5 N VALUE
will have been lost. The CDCLK frequency is required for reprogramming them
to generate 24MHz HD-A link BCLK. So provide a private interface for the
audio driver to query CDCLK.
This is a stopgap solution until a more generic interface between audio
and display drivers has been implemented.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For the CTR DRBG, the drbg_state->scratchpad temp buffer (i.e. the
memory location immediately before the drbg_state->tfm variable
is the buffer that the BCC function operates on. BCC operates
blockwise. Making the temp buffer drbg_statelen(drbg) in size is
sufficient when the DRBG state length is a multiple of the block
size. For AES192 this is not the case and the length for temp is
insufficient (yes, that also means for such ciphers, the final
output of all BCC rounds are truncated before used to update the
state of the DRBG!!).
The patch enlarges the temp buffer from drbg_statelen to
drbg_statelen + drbg_blocklen to have sufficient space.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull USB bugfixes from Greg KH:
"Here's a round of USB bugfixes, quirk additions, and new device ids
for 3.16-rc4. Nothing major in here at all, just a bunch of tiny
changes. All have been in linux-next with no reported issues"
* tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: delete td from req's td list at ep_dequeue
usb: Kconfig: make EHCI_MSM selectable for QCOM SOCs
usb-storage/SCSI: Add broken_fua blacklist flag
usb: musb: dsps: fix the base address for accessing the mode register
tools: ffs-test: fix header values endianess
usb: phy: msm: Do not do runtime pm if the phy is not idle
usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq
usb: gadget: gr_udc: Fix check for invalid number of microframes
usb: musb: Fix panic upon musb_am335x module removal
usb: gadget: f_fs: resurect usb_functionfs_descs_head structure
Revert "tools: ffs-test: convert to new descriptor format fixing compilation error"
xhci: Fix runtime suspended xhci from blocking system suspend.
xhci: clear root port wake on bits if controller isn't wake-up capable
xhci: correct burst count field for isoc transfers on 1.0 xhci hosts
xhci: Use correct SLOT ID when handling a reset device command
MAINTAINERS: update e-mail address
usb: option: add/modify Olivetti Olicard modems
USB: ftdi_sio: fix null deref at port probe
MAINTAINERS: drop two usb-serial subdriver entries
USB: option: add device ID for SpeedUp SU9800 usb 3g modem
...