Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-08-15
This series contains fixes to i40e only.
Anjali provides two fixes for i40e, first adds a check for non-active
VF before sending admin queue messages to the VFS. This resolves a
potential kernel panic which would happen whenever we got a Tx hang and
there were VFS that were not up or enabled. The second fix adds
additional checks so that we do try to access a VF that is not up or
enabled which would dereference a null pointer.
Jesse fixes a i40e PTP bug where the hang detection routine was never
being run when PTP was enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1d023284c3 ("list: fix order of arguments for
hlist_add_after(_rcu)") was incorrectly rebased on top of
d9124268d8 ("batman-adv: Fix out-of-order
fragmentation support"). The parameter order change of the rebased patch was
not re-applied as expected. This causes a memory leak and can cause crashes
when out-of-order packets are received. hlist_add_behind will try to access the
uninitalized list pointers of frag_entry_new to find the previous/next entry
and may modify/read random memory locations.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: phy: bcm7xxx internal PHY fixes
Here are 3 small fixes for the Broadcom BCM7xxx internal PHY targeting
suspend/resume issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7xxx internal Gigabit PHY on 28nm process do not need anything
special to be done during suspend, remove the suspend callback since it
might be harmful rather than useful. While at it, update the comment
above bcm7xxx_suspend() to reflect that it applies only to 40nm and 65nm
process PHY devices.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
The BCM7xxx internal Gigabit PHYs on 28nm process platforms come out
reset without any half-duplex or "hub" compatible advertised modes,
which was causing auto-negotiation issues coming out of S3
suspend/resume, we just could not establish a link with a half-duplex
only link partner.
Make sure that the resume function properly re-configures the PHY device
to advertise all supported modes.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
A wildcard entry with the 32-bits OUI 0x600d8400 was added as part of
the BCM7xxx internal PHY driver, but that entry might match other PHYs
that are not covered by this driver, so let's just remove it.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
There's no legacy board anymore, genmai now boots with multiplatform
support only. Remove the leftovers.
Makefile.boot portion pointed out by Paul Bolle.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa@sang-engineering.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
[horms+renesas@verge.net.au: squashed in patch containing
Makefile.boot change]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the Lager board specific device node part for VIN1 (composite video in);
add the device node for Analog Devices ADV7180 video decoder to IIC2 bus.
Add the necessary subnodes to interconnect VIN1 and ADV7180 devices.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[Sergei: rebased, edited changelog and summary]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Koelsch board dependent part of the VIN1 device node. Add the device
node for Analog Devices ADV7180 video decoder to I2C2 bus. Add the necessary
subnodes to interconnect VIN1 and ADV7180 devices.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Henninger board dependent part of the VIN0 device node. Add the
device node for Analog Devices ADV7180 video decoder to I2C2 bus. Add the
necessary subnodes to interconnect VIN0 and ADV7180 devices.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The genmai defconfig file has been removed by
3ed27bd90d ("ARM: shmobile: genmai: remove defconfig")
so remove its entry in the MAINTAINERS accordingly.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on the DTS
Notes:
- MTD_SPI_NOR is a dependency for MTD_M25P80 since commit
03e296f613 ("mtd: m25p80: use the SPI
nor framework") and commit e43b20619b
("mtd: spi-nor: shorten Kconfig naming").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on the DTS
Notes:
- MTD_SPI_NOR is a dependency for MTD_M25P80 since commit
03e296f613 ("mtd: m25p80: use the SPI
nor framework") and commit e43b20619b
("mtd: spi-nor: shorten Kconfig naming").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on the DTS
Notes:
- MTD_SPI_NOR is a dependency for MTD_M25P80 since commit
03e296f613 ("mtd: m25p80: use the SPI
nor framework") and commit e43b20619b
("mtd: spi-nor: shorten Kconfig naming").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on the DTSes
Notes:
- MTD_SPI_NOR is a dependency for MTD_M25P80 since commit
03e296f613 ("mtd: m25p80: use the SPI
nor framework") and commit e43b20619b
("mtd: spi-nor: shorten Kconfig naming"),
- I2C_RIIC was enabled in the old genmai_defconfig.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the missing call to shmobile_init_late() to r8a7778_init_late().
This should make sure Suspend-to-RAM and CPUIdle are setup as expected
on bockw.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No more device needs to be added from platform code when booting the
reference platform, move MTU2 registration from setup-r7s72100.c to
board-genmai.c and remove the now empty r7s72100_add_dt_devices()
function.
As the genmai_add_standard_devices() function is now identical to the
default init_machine implementation, remove it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There is one design rule according to SAI's reference manual:
If the transmitter bit clock and frame sync are to be used by both transmitter
and receiver, the transmitter must be configured for asynchronous operation
and the receiver for synchronous operation.
And SYNC of TCR2 is a 2-width control bit:
00 Asynchronous mode.
01 Synchronous with receiver.
10 Synchronous with another SAI transmitter.
11 Synchronous with another SAI receiver.
So the driver should have set SYNC bit of TCR2 to 0x0, and meanwhile set SYNC
bit of RCR2 to 0x1 (Synchronous with transmitter).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI PXA2XX core layer has dependency on common clock framework
to obtain information on host supported clock rate. Thus, we
setup the clock device in the PCI glue layer to enable PCI mode
host pass in the clock rate information.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This adds an initial machine driver for the ES8328 audio codec on Freescale
boards. The driver supports headphones and an audio regulator for an onboard
speaker amp.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a codec driver for the Everest ES8328. It supports two separate audio
outputs and two separate audio inputs.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The new Renesas R-Car Gen2 DMA Controller driver (rcar-dmac) requires
explicit configuration of the DMA slave bus width.
Hardcode the DMA transfer size to 4 bytes, as MSIOF DMA is limited to
32-bit words.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>