The new Renesas R-Car Gen2 DMA Controller driver (rcar-dmac) requires
explicit configuration of the DMA slave bus width.
Hardcode the DMA transfer size to 1 byte for both directions, as that's
the only supported configuration (16-bit DMA support was removed in
commit 9c5de2c175 ("spi: rspi: Remove
unused 16-bit DMA support")).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the devm_kasprintf() helper function instead of open coding
error-prone buffer handling and string formatting.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
If dmaengine_prep_slave_sg() or dmaengine_submit() fail, we may leak
unused DMA descriptors.
As per Documentation/dmaengine.txt, once a DMA descriptor has been
obtained, it must be submitted. Hence:
- First prepare and submit all DMA descriptors,
- Prepare the SPI controller for DMA,
- Start DMA by calling dma_async_issue_pending(),
- Make sure to call dmaengine_terminate_all() on all descriptors that
haven't completed.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
If dmaengine_prep_slave_sg() or dmaengine_submit() fail, we may leak
unused DMA descriptors.
As per Documentation/dmaengine.txt, once a DMA descriptor has been
obtained, it must be submitted. Hence:
- First prepare and submit all DMA descriptors,
- Prepare the SPI controller for DMA,
- Start DMA by calling dma_async_issue_pending(),
- Make sure to call dmaengine_terminate_all() on all descriptors that
haven't completed.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unused definition which cause the following warnings
drivers/spi/spi-omap-100k.c:73:0: warning: "WRITE" redefined [enabled by default]
include/linux/fs.h:193:0: note: this is the location of the previous definition
drivers/spi/spi-omap-100k.c:74:0: warning: "READ" redefined [enabled by default]
include/linux/fs.h:192:0: note: this is the location of the previous definition
Signed-off-by: Nick Krause <xerofoiffy@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code only allows direct routing of the WM8994 microphone
detection signal to a GPIO this change adds support to demux the
interrupt from the main interrupt line of the codec.
Signed-off-by: Nikesh Oswal <nikesh@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add DAPM calls to enable/disable the Class D amp.
Also add a DAPM call to turn off the PLL upon
the stream completing.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
sst_ops need to use the sst driver context. So pass sst device as argument,
which can be used to retrieve sst context.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The previous patch (ASoC: fsl_sai: Add asynchronous mode support) added
new Device Tree bindings for Asynchronous and Synchronous modes support.
However, these two shall not be present at the same time.
So this patch just simply makes them exclusive so as to avoid incorrect
Device Tree binding usage.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SAI supports these operation modes:
1) asynchronous mode
Both Tx and Rx are set to be asynchronous.
2) synchronous mode (Rx sync with Tx)
Tx is set to be asynchronous, Rx is set to be synchronous.
3) synchronous mode (Tx sync with Rx)
Rx is set to be asynchronous, Tx is set to be synchronous.
4) synchronous mode (Tx/Rx sync with another SAI's Tx)
5) synchronous mode (Tx/Rx sync with another SAI's Rx)
* 4) and 5) are beyond this patch because they are related with another SAI.
As the initial version of this SAI driver, it supported 2) as default while
the others were totally missing.
So this patch just adds supports for 1) and 3).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is one design rule according to SAI's reference manual:
If the transmitter bit clock and frame sync are to be used by both transmitter
and receiver, the transmitter must be configured for asynchronous operation
and the receiver for synchronous operation.
And SYNC of TCR2 is a 2-width control bit:
00 Asynchronous mode.
01 Synchronous with receiver.
10 Synchronous with another SAI transmitter.
11 Synchronous with another SAI receiver.
So the driver should have set SYNC bit of TCR2 to 0x0, and meanwhile set SYNC
bit of RCR2 to 0x1 (Synchronous with transmitter).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds software reset code in dai_probe() so as to make a true init
by clearing SAI's internal logic, including the bit clock generation, status
flags, and FIFO pointers.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Original driver didn't store the number of slots, just fix the slot number
to 2, use this default number to calculate bclk and pins for TX/RX.
In this patch, add one parameter for slots, and update the calculation of
bclk and pins of TX/RX. Then driver will be compatible with slots > 2 in
TDM mode.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Freescale Generic ASoC Sound Card is a general ASoC DAI Link driver that
can be used, ideally, for all Freescale CPU DAI drivers and external CODECs.
The idea of this generic sound card is a bit like ASoC Simple Card. However,
for Freescale SoCs (especially those released in recent years), most of them
have ASRC (Documentation/devicetree/bindings/sound/fsl,asrc.txt) inside. And
this is a specific feature that might be painstakingly controlled and merged
into the Simple Card driver.
So having this driver will allow all Freescale SoC users to benefit from the
simplification to support a new card and the capability of wide sample rates
support through ASRC.
The driver is initially designed for sound card using I2S or PCM DAI formats.
However, it's also possible to merge those non-I2S/PCM type sound cards, such
as S/PDIF audio and HDMI audio, into this card as long as the merge will not
break the original function and as long as there is something redundant that
can be abstracted along with I2S type sound cards.
As an initial version, it only supports three cards that I can test:
imx-audio-cs42888, a new card that links ESAI with CS42888 CODEC
imx-audio-sgtl5000, just like the old imx-sgtl5000.c driver
imx-audio-wm8962, just like the old imx-wm8962.c driver
The driver is also compatible with the old Device Tree bindings of WM8962 and
SGTL5000. So we may consider to remove those two drivers after this driver is
totally enabled. (It needs to be added into defconfig)
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Forgot to add a return for err_disable goto statement.
Causes compile warning of control reaching end of non-void
Signed-off-by: Brian Austin <briann.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch adds device tree bindings file for the Cirrus Logic CS35L32
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic CS35L32 Boosted Amplifier
I2S output provides monitor data to the SOC/CODEC/DSP for speaker protection/enhancement algorithms
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Dropping the const qualifiers prevents "passing argument 1 of ‘of_node_put’
discards ‘const’ qualifier from pointer target type" type warnings when
compiling the code dropping reference to cpu_of_node, codec_of_node or
platform_of_node with with an of_node_put() function call.
This lets us to avoid casting to struct device_node * or caching variables
internally in drivers just to be able to properly drop a reference to the
OF node on clean up paths.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add driver support for HiSilicon Hi6421 voltage regulators.
Two rules for regulator enabling are defined in hi6421 spec:
1) Between disable and enable of each regulator (LDOs or BUCKs), there must
be a protection gap. Use @off_on_delay of regulator core to implement this.
2) No two regulators can be enabled at the same time. Use mutex in
hi6421_regulator_pdata to ensure this. A protection gap of 100us is added
into each LDO/BUCK's .enable_time.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
As with commit 981c3a4ff8 (MAINTAINERS: Restore "L:
linux-kernel@vger.kernel.org" entries) restore the mailing list entry
for the regmap framework in order to assist users in finding the list
if they read the file instead of using get_maintainers.pl.
Signed-off-by: Mark Brown <broonie@linaro.org>
Device-Tree binding for device endianness
Index Device Endianness properties
---------------------------------------------------
1 BE 'big-endian'
2 LE 'little-endian'
For one device driver, which will run in different scenarios above
on different SoCs using the devicetree, we need one way to simplify
this.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For many drivers which will support rich endianness of Devices
need define DT properties by itself with the binding support.
The endianness using regmap:
Index Device Properties if needs bytes-swap,
or just ignore it
-------------------------------------------------------------
1 BE 'big-endian'
2 LE 'little-endian'
The properties include all the register values and the buffers.
And these properties are very usful for the MMIO devices:
Such as: a memory-mapped device, on one SoC is in BE mode, while
in another SoC will be in LE mode, and the CPU will always in LE
mode.
For the first case, we must use cpu_to_be32/be32_to_cpu for
32-bit registers accessing, so the 'big-endian' property is needed.
For the second case, we can just ignore the bytes-swap
functions like cpu_to_le32/le32_to_cpu, so the 'little-endian'
property could be abscent.
And vice versa...
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some regulator require a minimum delay between its disable and next enable.
This is to avoid damages when out-of-range frequent disable/enable of a
single regulator can bring to the regulator chip.
Add @off_on_delay to struct regulator_desc. Device drivers' can use this field
to set this guard time.
Add @last_off_jiffy to struct regulator_dev. When @off_on_delay is set by
driver, regulator core can store its last off (disable) time into this field.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
A common delay function can be helpful when implementing new features. Factor
it out to maximize code reusability.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
struct regulator_ops *ops is a member in struct regulator_desc, which gets
its value from individual regulator driver upon regulator_register() and
is used by regulator core APIs. It's not allowed for regulator core to
modify any of these callbacks in *ops. Add 'const' qualifier to enforce that.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The regulator core supports this to allow the configuration to be inspected
at runtime even if no software management is enabled.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch makes the regulator description macro take minimum and
steps voltage as parameter. In this way many repeated macros can be
removed. Now these macros are repeated only if the the LDO/BUCK ctrl
registers have non-linear positions. The good thing is these ctrl registers
are mostly linear so they are not passed as parameters.
This patch reduces the code size and also allow easy addition of more
s2mpxxx PMIC drivers which differs a lot in minimum/step voltages.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch makes the regulator description macro take minimum and
steps voltage as parameter. In this way many repeated macros can be
removed. Now these macros are repeated only if the the LDO/BUCK ctrl
registers have non-linear positions. The good thing is these ctrl registers
are mostly linear so they are not passed as parameters.
This patch reduces the code size and also allow easy addition of more
s2mpxxx PMIC drivers which differs a lot in minimum/step voltages.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a cleanup patch and moves min/step voltages in a common samsung
header file so that they can be used by other s2mpxxx PMIC drivers. Only
few required macros are added currently and others can be added if needed.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
As with commit 981c3a4ff8 (MAINTAINERS: Restore "L:
linux-kernel@vger.kernel.org" entries) restore the mailing list entry
for the regulator framework in order to assist users in finding the list
if they read the file instead of using get_maintainers.pl.
Signed-off-by: Mark Brown <broonie@linaro.org>
The PMIC interrupt pinctrl line was added to the rk3288-evb-act8846,
but it's the same line on both the ACT8846 version and the RK808
version. This makes a lot of sense since they share the same SoC
daugherboard. Move the pinctrl definition to the common file so we
can use it for the RK808 version.
NOTE: The PMIC interrupt doesn't _actually_ go to the PMIC on the
ACT8846 version of the board (it does on the RK808), but our
convention is to label things as they're labelled on the schematics.
In the very least you can argue that this is the interrupt from the
PMIC daughtercard even if it doesn't actually go to the PMIC chip.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables basic SD and eMMC support. Things are not yet running at
the fastest speed and we don't have the regulators specified, but we
can at least use the eMMC and SD cards now.
A note:
* Though MMC DDR50 mode is partially supported in the dw_mmc
rk3288-specific code in Addy's patch, Addy's patch doesn't add
tuning support. That means DDR50 mode is not reliable. From the
3288 TRM: "Tuning is required for other speed modes-such as
DDR50-even though the output delay from the card is less than one
cycle." Thus, we don't enable MMC DDR50 mode in this patch.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds support for the sdmmc and emmc ports on the rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes the coding style error :
"WARNING: else is not generally useful after a break or return"
reported by checkpatch.pl
Signed-off-by: Vibi Sreenivasan <vibisreenivasan@linuxmail.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a couple comedi drivers that duplicate some of the register
defines used by the 8255 module. Move these defines into the header
so the duplication can be removed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers that use this module with memory mapped io all have the
ioremap'ed base address stored in the comedi_device 'mmio' member.
Introduce a default (*io) function that does 8-bit memory mapped io.
Modify subdev_8255_init() so that it takes a flag parameter indicating
if the io is port or memory mapped. Make the function static and rename
it to __subdev_8255_init().
Introduce two exported wrappers for __subdev_8255_init():
subdev_8255_init() - for drivers that do 8-bit port io
subdev_8255_mm_init() - for drivers that do 8-bit memory mapped io
Use subdev_8255_mm_init() in the drivers that do 8-bit memory mapped io
and remove the private (*io) functions.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, all users of is module that use the default (*io) function
pass an 'iobase' to subdev_8255_init() of the form:
dev->iobase + OFFSET_TO_8255_BASE_REG
Now that the (*io) callback includes the comedi_device 'dev' pointer
the 'dev->iobase' does not need to be included.
Modify the default (*io) function, subdev_8255_io(), to automatically
add the dev->iobase to the address when reading/writing the port.
For aesthetics, rename the subdevice private data member to 'regbase'.
Also, rename the local variables in this module that are used to
access this member.
Add a comment in dev_8255_attach() about the 'iobase' that is passed
to subdev_8255_init(). For manually attached 8255 devices the io
region is requested with __comedi_request_region() which does not
set dev->iobase. For these devices the 'regbase' is actually the
'iobase'.
Remove the, now unnecessary, dev->iobase from all the callers of
subdev_8255_init(). There are a couple drivers that only passed the
dev->iobase. For those drivers pass a 'regbase' of 0x00.
Note that the das16m1 driver is a bit goofy. The devpriv->extra_iobase
is requested using __comedi_request_region() which does not set the
dev->iobase. But the starting address passed is dev->iobase + DAS16M1_82C55
so a 'regbase' of DAS16M1_82C55 is passed to subdev_8255_init().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>